Just to let you all know, there was a silver lining in my 2 year search and part replacefor my 2005 GMC savana v8. Replaced all coils ,plugs and wires but heard on UA-cam, to check and have the mechanic perform ,for code P0300, a crankshaft calibration/relearn procedure. It's essential and a low cost fix for high mileage vand and trucks. GMC is plagued with it . Check it before performing all the expensive services first.
Scion TC is doing this. Flashing engine light for sure and I just changed spark plugs. Should it be ok to at least drive back and forth to work for a few days?
The misfire on my van scared the shit out of me. I'm not sure whether to junk the van or fix it. On one hand, it's a really reliable, fun van, but on the other hand, I have three cars to work on and it's starting to rust out underneath.
Mine started flashing and so i connected a code reader to the OBD-II port and it showed up with no codes. It flashed for a about a minute yesterday and hasnt flashed since
My 2003 Ranger started doing this. For me, the light came on a week ago, but started running rough at a stop...then it started flashing. Runs fine, except at idle (stopped).
Would you recommend towing the vehicle or is driving it to the local shop alright? The engine light was flashing. It no longer is flashing and it’s off but it was flashing before. Also my vehicle jerks on braking and acceleration.
For me it was something like "intake manifold gasket" where the coolant was getting into the cylinder and misfiring real bad. It'd also smoke on cold start and sputter at idle
Thank man I was driving my dodge van 3500 and the engine light was flashing I pulled over then I turn the van off & 2 minutes later I turn it on and it was driving fine so it could be missed fire because the only thing pop up was emission p0455 that it so it have to be miss fire ????
I’m experiencing the same problem. Mines actually happened yesterday. Once I turned my car on it started peeping and after I shut it off 20min later it stopped. I drove it a little today but it’s driving funny, it’s also shaking alot! What should I do? How much is it usually to fix this type of problem? I also have a bad Axel ..
It's usually a relatively inexpensive repair. You would have to first start by getting the codes read from your computer. A lot of places like AutoZone will read the codes for you for free. Once you find out what cylinder is misfiring then I can suggest course of action
I think my catylic converter was stolen 😩 the engine shakes and clicks and I just got a flashing light today it lost power quickly and I had to get off the road
my check engine light only flashes when the car is on “ON” but it doesn’t flash when the car is actually running? how should i approach this? thank you
My 2006 Honda Pilot started doing this, struggles to accelerate, and shakes/ sputters . Shop told me I probably need a new engine. Could that be true ?
Isn't a cat problem related to a o2 sensor not switching from 1v to .5v flashing means imminent damage due to running lean and getting no closed loop reading I though
Normally that is what you would do and my wife's 2007 Nissan Altima I've already changed the coil packs and spark plugs and I did not want to have to take that car apart again I just changed them a couple months ago so it's got to be something else it's definitely misfiring no doubt but I don't think it's from bad spark plugs or coil pack, I did have it running and I pulled the airbox off and it seemed like it got a little pep in it step so I think it might have something to do with not getting enough air but if I plug in OBD sensor up it's not going to tell me that all it's going to say is I got lean air and gas mixture. Do they make OBD sensors that tell you exactly what the hell the problem is because that would be great I would buy one of those in a heartbeat
I been having the same problem my light been flashing for a week now changed the spark plugs wires and coil still shaking … haven’t checked the fuel injectors yet but my code is 3006 which is the 6th cylinder I need help
*Please anyone to reply would be a great help to me* My Check Engine Light began flashing. I pulled over and immediately had it towed to a mechanic they replaced all the plugs and ignition coils. So I picked it up today and even though the check engine light is not on it feels a little shakey during travel? 2013 Ford F150 v6
@@alexis_dc2 Bad mechanic is exactly what it was. When they installed new plugs they cracked one and sent me home in it. Ugh. Ended up costing me more to get it diagnosed because I told then the plugs and coils shouldn't be the issue since they were supposivly replaced 🙃 Got the bad plug replaced...truck feels much better now. Thank you for the feed back!
I had a flashing check engine light yesterday when I went to start my car. I freaked out and turned it off and I turned it back on haha it was gone once I restarted the car. It drives perfectly fine. I didn't feel the car running sluggish or anything out of the ordinary. I went to O Reilly and the reader didn't get anything. my dad replaced the spark plugs a couple of months ago when he changed the serpentine belt so it can't be that. Should I have a mechanic give the car a look over just to be safe? The car is a 99 dodge intrepid. It's only got 63k original miles and I had the oil changed a few weeks ago too. Idk how soon a mechanic could look at it tho and I'm a little sketched out about taking my car right now cause I feel like mechanics are gonna take advantage of customers cause it's tax return season and we just received our stimulus checks 😐
I have a 2009 Toyota Camry and my check engine light doesn’t flash it just sits there and then it goes off for a few days then it comes back but it doesn’t flash what does that mean
I have a 2017 Kia Soul and on my way home tonight, I noticed it flashed for 3 seconds then stopped. I noticed my gas cap was loose and fixed it, hopefully it's nothing serious
What about a car that’s sat for 30 days? All I did was replace a factory battery and now it has an intermittent miss and a flashing check engine light that flashed about 10 times then stopped. Bad gas?
On a car that has been sitting, I would still suspect an ignition coil or spark plug wires. Depending on the type of ignition system it has. Moisture likes to build up in the spark plug tubes on and engine that has not been run for some time and the moisture can cause a misfire. Water and electricity do not mix. I would scan it for codes and spray the plug wire or coil of the effected cylinder with WD40 and see if the misfire goes away.
I have a 14 year old 2005 chevy 2500 6.0 With 4500 miles on it. Yes 4500 miles. I just bought it 300 mile age. Truck runs great but I just started getting a PO307 code. Misfire on 7. So I changed #5 coil with #7 and It still gets the same code PO307. I'm thinking clogged injector on 7 from sitting for a long time or bad gas.. Sometimes check engine light blinks and say on. I put some Seafoam in the tanks and now check engine light blinks but doesn't stay on and just stops blinking. It started when I filled the tank with gas, so maybe bad gas. Some time when it flashes I can here a back fire. I'm going to try some more Injector cleaner in the tank. What do you think. Thanks
i have the same problem with my 2014 Hyundai Veloster turbo i change the plugs but that wasn't the case and i am still getting p0300 codes so i order 4 packs of brand new ignition coils and wiring harness off amazon I'm a hundred percent sure that its time to changed them thank you for video two thumbs up
My vehicle was checked for spark plug codes. and the computer did not find a code for spark plugs. But it was misfiring last night and the check engine light was flashing. What does that mean?
Sounds like it was misfiring, unfortunately if it didn't set a code it would be hard to track down unless it is misfiring at the time of diagnostic. What kinda of car is it.
2006 Highlander, 3.3 V6 maintenance light now stays on. Engine runs perfectly fine and no codes. What is the problem? Two mechanics say it’s the computer.
Maintenance light or check engine light? It is possible for the clusters go bad because of age I know Toyota’s you have to turn off the vehicle, hold down the bottom on the cluster and turn it back on the on position for the maintenance light to go away I’ve seen many oil change places that don’t even do that right haha it’s really easy it takes less than 2 mins to do it.
Mine was flashing a couple of days ago when I turned the engine on. It flashed for about a minute before it stopped. Should I still get this checked?, it hasn't happened since.
Damnnnn I had one more day to go to work then I could get this fixed now that my light is flashing I can't drive 😫 ....I guess it's uber for me tomorrow 😒
My light was on one day.. the next day it was blinking..then the next it was off... and hasn't been back on since.. maybe 3 days now.. should I be worried?
badnewzsteve same thing happened to me. I was driving it, it began to flash so I pulled over and shut my car off for two minutes. Then I turned my car back on and it wasn’t flashing anymore
My A/T LIGHT FLASHES 16 TIMES cranks but wont start an my alarm system isnt working anymore do to a mechanic after he put his expensive scanner on smh plus he did a probe test an some other things I'm not sure of
My cel is flashing from start up and it says stabilitrak off and service traction control also it feels lkke the truck vibrites/shakes..dont know whats wrong.
chakorta 25 That’s GM for you, but then again, my 2008 Dodge 1500 has a check engine light with no codes, so I guess I’ll just reset it. Doesn’t even feel like there’s anything wrong. Checked all plugs, connections, cleaned mass airflow sensor, checked all fluids, and still drives and runs fine. Hopefully just a false reading somewhere in the system...
@@CanadianLag one thing. Why the hell are you flooring it? That's bad for you engine right there. If it misfires it a back fire. That means left over exhaust fumes are rushing out of the tale pipe.
My civic started to flashing the engine light an stalled out on me would not turn on anymore so I cant even do any test all I did was swap the plugs an checked fuses I did compression test I'm getting low reads any advice on my next move for here .? My only read for 120 was the last plug slot all the others were not reading or bearly
renault clio mk3 1.4 16v petrol 2006-flashing emmissions light only when car idling--------scan reads all the time misfire cyclinder-3-----4 mechanics at 4 differant garages cant find what is causing it carried out same test as you with new plugs and coil---put numerous gaskets on as differant ones thought it was vacum problem-changed fuel rail-throttle body 4 pencil coils new ngk plugs and ran scan on big garage diagnostic machine-misfire cyclinder 3-no other info-costing me a lot of cash for parts that appear not to have been needed-i mentioned cat as car seems little smokey( car driving 100% but wont pass mot test in uk with this problem)-they all dismissed this any help welcome thanks in advance
I was just driving home and and my Light started Flashing and 5 mins later the car died when I was on the freeway when I hit the 3RPM the car was Jerking do you think it’s a Transmission problem or An Air sensor I also restarted the car and drove it to my Stall ?
Random Videos If there aren’t any major issues, just keep driving it! Trucks will last a long time! I have a 2008 Dodge Ram 1500 with 325,000 miles, and just had the check engine light come on for the first time! Still all original drivetrain, and running great! Hopefully just a bad sensor!
I had this with my old honda civic. The car would start violently shaking and almost stall. I kept driving it and eventuallly it started running fine again lol. Check engine light was still on but the car just stopped giving me problems with stalling. Didn't change the plugs nothing.
@@erictech201 Well this was a civic. But it started doing it at about 140,000 miles...mand just randomly stopped. I literally did no maintenance on it lol
Check out The Flat Rate Mechanics Tool Store on Amazon goo.gl/M8MpdC
i my check engine light is flashing & the car is kind of shaking how can i figure out what that is by having the car scanned ?
How much does it cost to fix it?
@@Janice835 The qqqqq
Hello I’m 1 hour from my mechanic … do you think it is ok … can I make it or should I get a tow?
It would've been helpful to show how u used the tool to diagnose the problem and find which cylinder is misfirinf
Mines start flashing when I drive over 60mph any thoughts on what it can be?
Can extreme cold weather cause this bad of a misfire?
Not sure but my tahoe misfires so bad in the winter today it literally flashed for over 10 minutes
Just to let you all know, there was a silver lining in my 2 year search and part replacefor my 2005 GMC savana v8. Replaced all coils ,plugs and wires but heard on UA-cam, to check and have the mechanic perform ,for code P0300, a crankshaft calibration/relearn procedure. It's essential and a low cost fix for high mileage vand and trucks. GMC is plagued with it . Check it before performing all the expensive services first.
Its not always that, i redid all spark plus and wires and ingition coil so its something fuel like a fuel pump or fuel injector. Shouldve said that
Scion TC is doing this. Flashing engine light for sure and I just changed spark plugs. Should it be ok to at least drive back and forth to work for a few days?
Not ok what was the outcome?
Thank you for your help. My 2005 Buick Lasabre just started to run rough and smelled like rubber coming off. I will have it checked=☺
The misfire on my van scared the shit out of me. I'm not sure whether to junk the van or fix it. On one hand, it's a really reliable, fun van, but on the other hand, I have three cars to work on and it's starting to rust out underneath.
Mine started flashing and so i connected a code reader to the OBD-II port and it showed up with no codes. It flashed for a about a minute yesterday and hasnt flashed since
So basically is it ok or not
It’s gon come bk, that was your warning
Crazy bro ever came back on?
I changed all my coil packs and spark plug on my 07 Chevy suburban 5.3 flex
My 2003 Ranger started doing this. For me, the light came on a week ago, but started running rough at a stop...then it started flashing. Runs fine, except at idle (stopped).
Did you know what it was?
@@josueahumada1888 I'm pretty sure it was a bad sensor and something related to that.
@@anthonyc1304 that's a misfire caused by valve problems man. Pretty common on ford rangers because they used cheap valves on the 3.0L motor.
Ive got PO700&711, trany temp sensor & module, will it be ok to drive camaro to dealer? About 5 miles
Would you recommend towing the vehicle or is driving it to the local shop alright? The engine light was flashing. It no longer is flashing and it’s off but it was flashing before. Also my vehicle jerks on braking and acceleration.
Hi. Will bad gas cause a flashing el?
I only have the flashing check engine light when i accelerate... Anybody knows why? The vehicle is shaking/stutering when it happens too. Thank you.
DashcamVideos you ever find out what it was
My car is same problem all plug changing and ignition coil changing.complaint is not solve
Yes it will do it much more under load. That is normal for a cylinder misfire.
Akhil Vijayan fuel pump 100%
For me it was something like "intake manifold gasket" where the coolant was getting into the cylinder and misfiring real bad. It'd also smoke on cold start and sputter at idle
Thank man I was driving my dodge van 3500 and the engine light was flashing I pulled over then I turn the van off & 2 minutes later I turn it on and it was driving fine so it could be missed fire because the only thing pop up was emission p0455 that it so it have to be miss fire ????
I’m experiencing the same problem. Mines actually happened yesterday. Once I turned my car on it started peeping and after I shut it off 20min later it stopped. I drove it a little today but it’s driving funny, it’s also shaking alot! What should I do? How much is it usually to fix this type of problem? I also have a bad Axel ..
It's usually a relatively inexpensive repair. You would have to first start by getting the codes read from your computer. A lot of places like AutoZone will read the codes for you for free. Once you find out what cylinder is misfiring then I can suggest course of action
The Flat Rate Mechanic Thanks!
@@FlatRateMechaniccould you suggest something for a cylinder 5 misfire?
I think my catylic converter was stolen 😩 the engine shakes and clicks and I just got a flashing light today it lost power quickly and I had to get off the road
Thanks bro
my check engine light only flashes when the car is on “ON” but it doesn’t flash when the car is actually running? how should i approach this? thank you
With a Defective coil , I change all plugs and coils as a set .
My 2006 Honda Pilot started doing this, struggles to accelerate, and shakes/ sputters .
Shop told me I probably need a new engine. Could that be true ?
@Green Drop Talk whats a dead hole?
Bro did u fix it, please
Isn't a cat problem related to a o2 sensor not switching from 1v to .5v flashing means imminent damage due to running lean and getting no closed loop reading I though
What if you replace the misfiring ignition coil and spark plug and it doesn’t solve the problem? The flashing engine light still persists. Sigh
Im having this same problem how did you end up fixing it?
Same for me
Once fixed does a check engine light turn off right away or it takes time.
It can be cleared or you will have to drive it with no problem for a little bit and it will clear itself as long as the problem was fixed.
Normally that is what you would do and my wife's 2007 Nissan Altima I've already changed the coil packs and spark plugs and I did not want to have to take that car apart again I just changed them a couple months ago so it's got to be something else it's definitely misfiring no doubt but I don't think it's from bad spark plugs or coil pack, I did have it running and I pulled the airbox off and it seemed like it got a little pep in it step so I think it might have something to do with not getting enough air but if I plug in OBD sensor up it's not going to tell me that all it's going to say is I got lean air and gas mixture. Do they make OBD sensors that tell you exactly what the hell the problem is because that would be great I would buy one of those in a heartbeat
You don't have coil packs and spark plugs
I been having the same problem my light been flashing for a week now changed the spark plugs wires and coil still shaking … haven’t checked the fuel injectors yet but my code is 3006 which is the 6th cylinder I need help
Check for vacuum leaks or check the fuel injectors for the #6 cylinder
*Please anyone to reply would be a great help to me*
My Check Engine Light began flashing. I pulled over and immediately had it towed to a mechanic they replaced all the plugs and ignition coils. So I picked it up today and even though the check engine light is not on it feels a little shakey during travel? 2013 Ford F150 v6
Mallery Smith maybe they did a bad job in replacing the parts. Could also be something to do with air intake to the car
@@alexis_dc2 Bad mechanic is exactly what it was. When they installed new plugs they cracked one and sent me home in it. Ugh. Ended up costing me more to get it diagnosed because I told then the plugs and coils shouldn't be the issue since they were supposivly replaced 🙃 Got the bad plug replaced...truck feels much better now. Thank you for the feed back!
Mallery Smith no problem!
They say that the stupidest question could be the best: would chopping the catalytic converter off resolve this problem??
If it's the cat then yes. That would work
Ok are is toya to won't pull up hill and check engine light came on and belt is squealing relley bad hot or cold car won't move or go up hill ?
Had first cylinder changed and a week later it happened again? Do I need a new car?
2014 Corolla
New engine
My 2011 Corolla is having the same problems as well after a pair of coils and fuel injectors. Did you ever have your problem resolved?
I had a flashing check engine light yesterday when I went to start my car. I freaked out and turned it off and I turned it back on haha it was gone once I restarted the car. It drives perfectly fine. I didn't feel the car running sluggish or anything out of the ordinary. I went to O Reilly and the reader didn't get anything. my dad replaced the spark plugs a couple of months ago when he changed the serpentine belt so it can't be that. Should I have a mechanic give the car a look over just to be safe? The car is a 99 dodge intrepid. It's only got 63k original miles and I had the oil changed a few weeks ago too. Idk how soon a mechanic could look at it tho and I'm a little sketched out about taking my car right now cause I feel like mechanics are gonna take advantage of customers cause it's tax return season and we just received our stimulus checks 😐
The check engine light flashes on my truck only when its turned off before turning it on, is that normal should I be worried? Please help
Same....did it ever give you any issues in the future
If ur catalitic convertor gets damaged can u just remove it?
I changed all my cyclinders and im still having problem and also thr ingnition coil
I have a 2009 Toyota Camry and my check engine light doesn’t flash it just sits there and then it goes off for a few days then it comes back but it doesn’t flash what does that mean
It means you should take it to autozone and ask them
I have code po301 n po304 changed plugs, coils, wires and coil harness. What could it be?
Ever find out what it was ? Maybe catalytic converter
I have a 2017 Kia Soul and on my way home tonight, I noticed it flashed for 3 seconds then stopped.
I noticed my gas cap was loose and fixed it, hopefully it's nothing serious
Here's big questions, what if there's no catalitic converter on the vehicle, would that cause the check engine to flash? Anyone know?
Very slightly educated opinion, yes.
What about a car that’s sat for 30 days? All I did was replace a factory battery and now it has an intermittent miss and a flashing check engine light that flashed about 10 times then stopped. Bad gas?
On a car that has been sitting, I would still suspect an ignition coil or spark plug wires. Depending on the type of ignition system it has. Moisture likes to build up in the spark plug tubes on and engine that has not been run for some time and the moisture can cause a misfire. Water and electricity do not mix. I would scan it for codes and spray the plug wire or coil of the effected cylinder with WD40 and see if the misfire goes away.
I have a 14 year old 2005 chevy 2500 6.0 With 4500 miles on it. Yes 4500 miles. I just bought it 300 mile age. Truck runs great but I just started getting a PO307 code. Misfire on 7. So I changed #5 coil with #7 and It still gets the same code PO307. I'm thinking clogged injector on 7 from sitting for a long time or bad gas.. Sometimes check engine light blinks and say on. I put some Seafoam in the tanks and now check engine light blinks but doesn't stay on and just stops blinking. It started when I filled the tank with gas, so maybe bad gas. Some time when it flashes I can here a back fire. I'm going to try some more Injector cleaner in the tank. What do you think. Thanks
I fixed it. Took out the injectors and cleaned them.
MrAlittle5150
I’m having the same issue, I’ll try cleaning the injectors
If I have no cat, will it cause any damage?
Yes you can burn your valves if you do not have any catalytic converters. I cut my muffler and my third cat off but have the two main cats on still
Its showing it in my 2010 Dodge Grand Caravan we hear the piston knocking we bought the head gasket and the piston was gone
i have the same problem with my 2014 Hyundai Veloster turbo i change the plugs but that wasn't the case and i am still getting p0300 codes so i order 4 packs of brand new ignition coils and wiring harness off amazon I'm a hundred percent sure that its time to changed them thank you for video two thumbs up
Did that work?
How to count cylinders, from left to right? Left one being first?
The firing order is diferrent for most cars. A quick google seach will tell the the firing order of yours.
Depends on the engine.
My vehicle was checked for spark plug codes. and the computer did not find a code for spark plugs. But it was misfiring last night and the check engine light was flashing. What does that mean?
Sounds like it was misfiring, unfortunately if it didn't set a code it would be hard to track down unless it is misfiring at the time of diagnostic. What kinda of car is it.
What if you have a catless
2006 Highlander, 3.3 V6 maintenance light now stays on. Engine runs perfectly fine and no codes. What is the problem? Two mechanics say it’s the computer.
Maintenance light or check engine light? It is possible for the clusters go bad because of age I know Toyota’s you have to turn off the vehicle, hold down the bottom on the cluster and turn it back on the on position for the maintenance light to go away I’ve seen many oil change places that don’t even do that right haha it’s really easy it takes less than 2 mins to do it.
Mine was flashing a couple of days ago when I turned the engine on. It flashed for about a minute before it stopped. Should I still get this checked?, it hasn't happened since.
Damnnnn I had one more day to go to work then I could get this fixed now that my light is flashing I can't drive 😫 ....I guess it's uber for me tomorrow 😒
Bummer. LMK how it gos
Same for me
I’ve a flashing CEL with my truck, I replaced all sparks plug and wires but still happening as soon as I start the engine. What should I do now?
I’m in the same boat :/
Cris Kampos
Have you done anything to your vehicle?
Ammar khalid egr valve and coil back fixed my problem!
My light was on one day.. the next day it was blinking..then the next it was off... and hasn't been back on since.. maybe 3 days now.. should I be worried?
badnewzsteve same thing happened to me. I was driving it, it began to flash so I pulled over and shut my car off for two minutes. Then I turned my car back on and it wasn’t flashing anymore
I wouldn't worry about it but the computer will have a stored code even if the light when out. Probably got a coil going bad.
@@FlatRateMechanic thanks
The Sports Warehouse same thing happened to me also. So did the light ever come back again or got any issue?
My A/T LIGHT FLASHES 16 TIMES cranks but wont start an my alarm system isnt working anymore do to a mechanic after he put his expensive scanner on smh plus he did a probe test an some other things I'm not sure of
Cute
My cel is flashing from start up and it says stabilitrak off and service traction control also it feels lkke the truck vibrites/shakes..dont know whats wrong.
chakorta 25
That’s GM for you, but then again, my 2008 Dodge 1500 has a check engine light with no codes, so I guess I’ll just reset it. Doesn’t even feel like there’s anything wrong. Checked all plugs, connections, cleaned mass airflow sensor, checked all fluids, and still drives and runs fine. Hopefully just a false reading somewhere in the system...
Mine started doing that also yesterday in my 2011 Silverado. My codes read cylinder 7 and multiple misfires.
My Malibu doesn't flash it just flickering and dim and I get Po650. Fun times
I have a Chrysler 300 07 and I fix the p0522 problem and oil light still comes on when I break but then it comes off.. Can any one help me...
Why does it only happen to me when I floor it any answers?🙋🏼♂️
Over reving the engine...
@@zkgarage1939 How tho i could be going like 60km/h floor it reach 80km/h and it mis fires
@@CanadianLag one thing. Why the hell are you flooring it? That's bad for you engine right there. If it misfires it a back fire. That means left over exhaust fumes are rushing out of the tale pipe.
Following
Plague Doctor • 5 years ago how do I fix that
My civic started to flashing the engine light an stalled out on me would not turn on anymore so I cant even do any test all I did was swap the plugs an checked fuses I did compression test I'm getting low reads any advice on my next move for here .? My only read for 120 was the last plug slot all the others were not reading or bearly
I did have a detonation in spark plug 1 the plug looked damaged on the tip looked smashed
Sounds like you had a timing chain or belt fail. I’d pull the heads and take a look...
Mine flashed 4 times and turned off
renault clio mk3 1.4 16v petrol 2006-flashing emmissions light only when car idling--------scan reads all the time misfire cyclinder-3-----4 mechanics at 4 differant garages cant find what is causing it carried out same test as you with new plugs and coil---put numerous gaskets on as differant ones thought it was vacum problem-changed fuel rail-throttle body 4 pencil coils new ngk plugs and ran scan on big garage diagnostic machine-misfire cyclinder 3-no other info-costing me a lot of cash for parts that appear not to have been needed-i mentioned cat as car seems little smokey( car driving 100% but wont pass mot test in uk with this problem)-they all dismissed this any help welcome thanks in advance
If it's only at idle I would suspect a vacuum leak or a burt valve in the cylinder head.
check the wires for the coil plug to the computer
Well my check engine light is on but, it’s NOT flashing.
I was just driving home and and my Light started Flashing and 5 mins later the car died when I was on the freeway when I hit the 3RPM the car was Jerking do you think it’s a Transmission problem or An Air sensor I also restarted the car and drove it to my Stall ?
Jay's Portraits yeah Crankshift sensor and spark plugs
Jay's Portraits $70 in parts me and my dad worked on it
Can this cause my car fire 🔥?
I mean anything can happy. But I would say most likely not.
Mines done that twice in a year aka last one today then went off on 5.3 sierra should i be worried or trade it in for a ford😂🤷🏻♂️
Random Videos
If there aren’t any major issues, just keep driving it! Trucks will last a long time! I have a 2008 Dodge Ram 1500 with 325,000 miles, and just had the check engine light come on for the first time! Still all original drivetrain, and running great! Hopefully just a bad sensor!
Random Videos why trade trash for trash
Can’t get over the sound of chewing and heavy breathing
I don’t have a cat but it runs like it has a horrid vacuum leak but there’s no leak anywhere
Check your coil pack same thing happened to me not even an hour ago.
I had this with my old honda civic. The car would start violently shaking and almost stall. I kept driving it and eventuallly it started running fine again lol. Check engine light was still on but the car just stopped giving me problems with stalling. Didn't change the plugs nothing.
Mathias Kanuck vtec?
@@erictech201 Nah. Just a 4 cylinder 1.8
Mathias Kanuck those accords are notoriously for stalling when age hits I have many cb7’s
@@erictech201 Well this was a civic. But it started doing it at about 140,000 miles...mand just randomly stopped. I literally did no maintenance on it lol
Mathias Kanuck it’s could of been valves being too tight but who knows
It means to put a seat belt on and drive
Anyone have a 2007 Lexus is250 that this is happening to ?
Maaan! Never buy a car from mechanics, they r so lazy to use a rag to keep dirty parts, instead of using the fabric seats.
Ali Hasan that’s just him bout caring
P0017? Anyone ?
Cam sensor
I was the 1k like :p
Vali verga. Im worth dick