Hello, friend. Thank you for watching the good video Let me ask you a question Instead of the encoder, there are 20 magnets in the pulley and 170 mm diameter of the encoder pulley There's a 185mm driver pulley on the motor side Can't we use counter up-down to accurately calculate the travel distance like the encoder?? Please tell me how to do it!!
Maybe this a little bit stupid question, but i'm not completely understand, how you convert discrete impulse I0.0 to analog value. One impulse you transfer to MD1000 but where you summarize impulses which gives analog value 1250 or 2500 etc?
first you should know what is encoder. encoder as a device when it rotates it produces pulses. basically. in that example you should connect that in digital signal instead of analog signal.but q.s? why? because pulses are digital values right? but also you should store that values in a big data as id1000 you can think like that you have a counter for counter up inout you should you a digital input but counter value must be md format. I hope that is clear for you
@@sinanartemis6176 Thanks for the information. I understand why he connected the encoder to a discrete input. I do not understand where the summary of impulses occurs. MD1000 is this a counter?
@@lockheadmaverick489 when it start to count that pulse store in that value for instance in 1 revolution it takes 360pulse and when it contunue that value also also increases you can think like counter
@lockheadmaverick489 yes MD1000 has been setup as a counter. In the beginning of the video when he is explaining the hardware configuration of the counter setup he mentioned the io address of the counter to start at memory address 1000. Kinda confusing but I found it.
You was the best in the youtube who expleain encoder with the short and bestway also with exempel. Thank you very much.
what software you used for the conveyor simulation? thank you
Hello, friend. Thank you for watching the good video
Let me ask you a question
Instead of the encoder, there are 20 magnets in the pulley and 170 mm diameter of the encoder pulley
There's a 185mm driver pulley on the motor side
Can't we use counter up-down to accurately calculate the travel distance like the encoder??
Please tell me how to do it!!
Very nice explained and for example thank you so much, make a different videos for encoder applications
Like
You are the best, can you tell me the simulator name ?
🎉
top d+++ valeu...
Sir here I Request that please make video in Hindi language also for better understanding
Which instruction to use to reset ID1000? many thanks
Please could you tell me the name of the simulator
Excellent tutorial!!
What conveyor simulation do you using ?
Maybe this a little bit stupid question, but i'm not completely understand, how you convert discrete impulse I0.0 to analog value. One impulse you transfer to MD1000 but where you summarize impulses which gives analog value 1250 or 2500 etc?
first you should know what is encoder. encoder as a device when it rotates it produces pulses. basically. in that example you should connect that in digital signal instead of analog signal.but q.s? why? because pulses are digital values right? but also you should store that values in a big data as id1000 you can think like that you have a counter for counter up inout you should you a digital input but counter value must be md format. I hope that is clear for you
@@sinanartemis6176 Thanks for the information. I understand why he connected the encoder to a discrete input. I do not understand where the summary of impulses occurs. MD1000 is this a counter?
@@lockheadmaverick489 when it start to count that pulse store in that value for instance in 1 revolution it takes 360pulse and when it contunue that value also also increases you can think like counter
@lockheadmaverick489 yes MD1000 has been setup as a counter. In the beginning of the video when he is explaining the hardware configuration of the counter setup he mentioned the io address of the counter to start at memory address 1000.
Kinda confusing but I found it.
What is the simulation software in the video? please
What software that you make Simulation?
F
@@ahmediibrahim.m3327 the name of simulation software is "F" ?!?!
TIA portal V17
Hi,can you program,I have one Conyer based machine,if support please send reply,then I explain
Thank you
How did you get differents speed between the setpoints ?
How you find out that encoder can move 15mm in a revolution, kindly clear it
How do I get these files blender? Can you help me ❤
Thanks for the video, l got a question, anyone can help, to convert distance in mm covered per pulse, you divided 15mm/360ppr, where did 15 come from
He found it from conveyor real speed ,it can be changed your project , I think
good
Please help me with the name of the stimulator.
Thanks
thankyou sir.
1:50 Why is the Network 1 needed at all?
Why rewrite %ID1000 to %MD1000?
Why convert Dint to Real?
Bc we need them as real to calculate mm per pulse
Hi. Thanks for sharing. What is the full name of the simulation software?
TIA Portal is good also
Why I can't open your Google drive
how the motor receive signal ? in real, ask you 1v a 5V
Hello eng. what software that used for simulation
tia portal
i need name of Simulation app? pls
What sofware simulation?
F
Plc