I really appreciate this video. I have all my gear setup right but im a novice and I could not figure out why I could not get any level from my mics without having the gain almost maxed. That of course was very noisy. I was almost about to buy a pre amp thinking the mixer pre's just weren't strong enough. After your video and explaining how to work the aux knobs I see where I went wrong. Thanks a lot!!! saved me a good bit of money.
Finally a instructional video most of the videos that are up are videos of the person pointing out how many pretty nobs he has on his console there is even one in two parts where the guy is basically saying look at all my. Pretty buttons doesn’t explain shit.
Try using the mixer tape output (Rca top of the mixer). You will have to connect the red/white rca cable in the output and the other end to a recorder or back into you system input and record via that way.
Hello, First of all nice explanation and video. Can you please explain how to use the TAP button (in effects) ? I didn't find in any manual an explanation on how to use it ? Thanks in advance
I really didnt know you could use it for the effects, I thought it was only for the Pitch? I really can't remember, I am sorry and I can't check because I don't own the mixer for a good 2 years now.
You could potentially damage your mic or mixer if the voltage are to high or overloaded. If the phantom power comes from the same unit, there's no voltage difference, and no damage can occur. However if your going to use separate units of power, it can be complicated with different power, hence causing damage to one unit. Buy something like a isolated splitter to control or block ground the power.
Would this mixer be useful for an internet radio station? How would you use this with a dj mixer,turntables etc? What if you have a guest on the show and is using the mic, but on occasion there voice gets louder and louder,is there a cut off switch, where by if they shout it will not damage the speakers? (so the level of the mic will never go higher than the level set no matter if they shout or not)
Controlling the feedback or raising the effect amount is down by the main FX knob on the channel. Like say my mic is on channel one, than the fx on the channel level will provide overall amount. the feedback control will come from where the main board is, the 2 orange close together to the right. They will balance the fx level.
I have a question.....I just purchased a 2222fx, which I want to go out to dslr camera that has mic input. the rca jacks on mixer.....how do I get them to work? I must not be pushing a button down to make them work. any idea?
Hi Elias, I have a couple questions: with many vocals do you do this for each channel? Like once you have it set for one channel, you can't change it really for the other channels right? Except on their own strip. Is that correct? Also, do you or are you suppose to keep the solo FX button down on the "sends"? And do you need to engage the other FX button that's on the "return" side? Like turning the knob is all you need to do? Lastly, do the "Aux sends" and "stereo Aux returns" work the same for your monitors? Do you need to (or should I be using them) to control the sound level? Look forward to your advice and thanks for the all the questions you have answered me on your other tutorial. Very much appreciated! Tracey C
most of the questions are answered in the following vid here .. ua-cam.com/video/ou_RUrzUkFg/v-deo.html .. so check it and for the first question, yes you will need to do it for each channel on their own strip.
Elias Gadgets Thanks again! Your vid was very helpful! As all your vids are! Are you then not answering any more questions on the behringer? Since you have a different board? But, If you are able to answer one more for me, I was wondering about the button on each strip right by the "Aux" knobs that says "pre". I assume that is the pre-fade button, but not sure exactly what or when that should be used? Again, I can't express how much I appreciate your advice and how it has helped me! Thanks sooo much!
Tracey C Oh no am still going to be always answering questions or guiding to other vids that may hold some answers to mixer. Yes Aux is the pre-fade and also the knobs are your auxiliary sends, they just allow you to control sound sent to other speakers from your main speakers or anything that you have hooked up to the mixer. Best to use these or I have only used these when I have my own external effects united that I hooked up to the mixer and I would channel the sound effects into the mixer controlling them and directing them to whichever channel strip I desired, you can control the amount applied to the channel strip via the fader or knob.
hi, i need yr help,i hve got behringer x1832usb but it can't seem to be doing anything like recording. whenever i try to record their are no vocal waves coming through,the vocal sounds are too low with noisy backgroung ,and there is a hissss coming through,,its really disturbing i hve installed the required drivers nothing is working,,what am i missing?,what should i do anyhelp plizz,,,thankx
Hello. I was searching the internet but cannot find if the the FX processor means using one effect at a time for ALL the channels (not one effect per channel). Am I right? Thank you!
Hello Elias do i have to buy a software or something extra to use these effects? Or if i only buy the mixer i can have accece to the effects you just show?
I need help setting up headphones! I have 6 headphone and a xenyx 2222 USB mixer. Do I need a separate headphone amp or does that mixer work?? Also The only ants I see for headphones are four channels and I have more than four headphones
I have recently bought the same mixer but it did not come with software instead it says on the box "free downloadable cd from behringer.The question is I don't know which one to download for my mixer and how.I tried to one of those but I could not.Help pls.Thanks!
hi thanx 4 the tutorial,i just have one question,can i use the external phantom power of the mic and the inbuilt one of the behringer x1832usb at the same time? will it damage the mic or? pliz help thnkx
Hey Elias I have the Behringer Xyenx USB1204 and I am trying to get someone to do a video on how to set it up for youtube videos using a mic such this video you made. Are you able to do a video on that. Step by Step starting from taking the item out the box.
ohh am about to give the mixer away as I have now replaced it with a digital mixer the Presonus 16.0.2, i guess I will have to see what I can do, maybe I will do a last video to cover a lot of questions and request I've had and include your question in that video, I will not be able to cover everything step by step but will see what I can do.
problem, when I using microfon with Effects, microfon signal with effects going ONLY to MAIN OUTPUTS. I want used 3outputs same time.. Main outputs -I have mic,with effects Sub outputs and Room control outputs I have only Microphone signal No Effects! whay? please help
How do i get this Mixer to work with my Dj Controller...i got the Numark NS7 Dj Controller System i got sound coming out the mixer only problem is i can not record my mix cd together with the mixer cause i got Serato Itch software for my Controler....can you help me to get it to record my normal mix cd..
hey mate, sorry for delay please click on the link under the video description, this will take you to the correct download section for your mixers driver.
I connect my desktop speakers to the phone jack but dont get the effects out loud but when recorded on my computer the effects work just fine. any idea how to send the effects to my speakers?
have you tried switching the source button and see what if it makes a difference? sorry I can't help much because its been good few years now since I had the mixer.
+EliasGadgets I don't know if you're still answering these, but is it possible to edit a clip after you record it with the filters and effects? Behringer qx1002usb
+Jeffrey Oden - Yes you can do that, it just depends what daw you use, I would recommend you use the software the comes with the mixer for all your eidting, you have the qx versions so you should have gotten a lot of bundled software made specifically to edit. If you didnt than go onto the website and download them for free.
Jeffrey Oden - wow really?? there should have been? here, go below the link and you should see access to the link here you can get all the software - click on downloads and than scroll down origin.behringer.com/EN/Products/QX1002USB.aspx
Please take this as constructive criticism, but maybe you should study up on the effects control a bit before posting. It was obvious that you didn't really know what was going on with the effects/parameter knob. But then again, NEITHER DO I. You fumble around with it as much as I do (with questionable results) but I didn't think I was knowledgeable enough to record a tutorial. I have a 1622 and was hoping to find out how the knob and the TAP button (which you don't even mention) are used to set the effects. Since there's even less information about this in the manual, I'll still keep looking...
I do know, I just wasn't covering them like many things about the mixer I don't go into. I use the effects a lot and also route my own via aux from my inserts with my own fx unit system into the mixer. Thank you and good luck.
I really appreciate this video. I have all my gear setup right but im a novice and I could not figure out why I could not get any level from my mics without having the gain almost maxed. That of course was very noisy. I was almost about to buy a pre amp thinking the mixer pre's just weren't strong enough. After your video and explaining how to work the aux knobs I see where I went wrong. Thanks a lot!!! saved me a good bit of money.
Thanks so much. I got a UB2442FX from an estate sale and had no idea how to use it.
Thank you for the FX mate- I watched so many videos that skipped that function. Cheers!
Finally a instructional video most of the videos that are up are videos of the person pointing out how many pretty nobs he has on his console there is even one in two parts where the guy is basically saying look at all my. Pretty buttons doesn’t explain shit.
THANKS! The only video I found that is this complete.
Try using the mixer tape output (Rca top of the mixer). You will have to connect the red/white rca cable in the output and the other end to a recorder or back into you system input and record via that way.
Hello, First of all nice explanation and video. Can you please explain how to use the TAP button (in effects) ? I didn't find in any manual an explanation on how to use it ? Thanks in advance
I really didnt know you could use it for the effects, I thought it was only for the Pitch? I really can't remember, I am sorry and I can't check because I don't own the mixer for a good 2 years now.
I discovered that when you use fx#9(echo), tap the TAP button a few times and it will echo in that rythm.
@@Offsettttt Thanks a lot man!
I am very happy with the excellent explanation you have given me. Thank you very much!
Bro thanks for this cause I was really struggling to set my Beringer mixer ... question tho setting it to the ROOM level is best for 🥁 drums don't it?
Very well explained. Thx for sharing it.
Hello, can you advise how to set the microphone not to go to the monitors but only to the headphones? Thank you
WELL ATICULATED, THANKS BUDDY
You could potentially damage your mic or mixer if the voltage are to high or overloaded. If the phantom power comes from the same unit, there's no voltage difference, and no damage can occur. However if your going to use separate units of power, it can be complicated with different power, hence causing damage to one unit. Buy something like a isolated splitter to control or block ground the power.
Qa
@@rojangurung0044 but Ryan used that mixer as reverb!
This was so helpful! Thank you!
How can I control the echo feedback and delay in the background using channel 08 ?
Would this mixer be useful for an internet radio station?
How would you use this with a dj mixer,turntables etc?
What if you have a guest on the show and is using the mic, but on occasion there voice gets louder and louder,is there a cut off switch, where by if they shout it will not damage the speakers? (so the level of the mic will never go higher than the level set no matter if they shout or not)
Well explained. Thank you.
Thank you!!
Hi Elias, thanks great vid! Can you explain how to control the feedback / repeat the amount of echo`s on effect number 15? thanks.....
Controlling the feedback or raising the effect amount is down by the main FX knob on the channel. Like say my mic is on channel one, than the fx on the channel level will provide overall amount. the feedback control will come from where the main board is, the 2 orange close together to the right. They will balance the fx level.
ok thank you Elias!
how do you reset the effects to normal speech?
I have a question.....I just purchased a 2222fx, which I want to go out to dslr camera that has mic input. the rca jacks on mixer.....how do I get them to work? I must not be pushing a button down to make them work. any idea?
Can I apply diferent efect on each channel?
Thanks bro! Very helpful!
Hi Elias,
I have a couple questions: with many vocals do you do this for each channel? Like once you have it set for one channel, you can't change it really for the other channels right? Except on their own strip. Is that correct?
Also, do you or are you suppose to keep the solo FX button down on the "sends"? And do you need to engage the other FX button that's on the "return" side? Like turning the knob is all you need to do?
Lastly, do the "Aux sends" and "stereo Aux returns" work the same for your monitors? Do you need to (or should I be using them) to control the sound level?
Look forward to your advice and thanks for the all the questions you have answered me on your other tutorial. Very much appreciated!
Tracey C
most of the questions are answered in the following vid here .. ua-cam.com/video/ou_RUrzUkFg/v-deo.html .. so check it and for the first question, yes you will need to do it for each channel on their own strip.
Elias Gadgets Thanks again! Your vid was very helpful! As all your vids are! Are you then not answering any more questions on the behringer? Since you have a different board? But, If you are able to answer one more for me, I was wondering about the button on each strip right by the "Aux" knobs that says "pre". I assume that is the pre-fade button, but not sure exactly what or when that should be used? Again, I can't express how much I appreciate your advice and how it has helped me!
Thanks sooo much!
Tracey C Oh no am still going to be always answering questions or guiding to other vids that may hold some answers to mixer. Yes Aux is the pre-fade and also the knobs are your auxiliary sends, they just allow you to control sound sent to other speakers from your main speakers or anything that you have hooked up to the mixer. Best to use these or I have only used these when I have my own external effects united that I hooked up to the mixer and I would channel the sound effects into the mixer controlling them and directing them to whichever channel strip I desired, you can control the amount applied to the channel strip via the fader or knob.
hi, i need yr help,i hve got behringer x1832usb but it can't seem to be doing anything like recording. whenever i try to record their are no vocal waves coming through,the vocal sounds are too low with noisy backgroung ,and there is a hissss coming through,,its really disturbing i hve installed the required drivers nothing is working,,what am i missing?,what should i do anyhelp plizz,,,thankx
What does "TAP" do.
Hello. I was searching the internet but cannot find if the the FX processor means using one effect at a time for ALL the channels (not one effect per channel). Am I right? Thank you!
how can I set the effects on 01 again? Is there a reset button?
Hello Elias do i have to buy a software or something extra to use these effects? Or if i only buy the mixer i can have accece to the effects you just show?
No software required. It works from mixer automatically.
@@guruzinbox okayy then tnx.
I need help setting up headphones! I have 6 headphone and a xenyx 2222 USB mixer.
Do I need a separate headphone amp or does that mixer work?? Also The only ants I see for headphones are four channels and I have more than four headphones
I have recently bought the same mixer but it did not come with software instead it says on the box "free downloadable cd from behringer.The question is I don't know which one to download for my mixer and how.I tried to one of those but I could not.Help pls.Thanks!
hi thanx 4 the tutorial,i just have one question,can i use the external phantom power of the mic and the inbuilt one of the behringer x1832usb at the same time? will it damage the mic or? pliz help thnkx
I cannot hear the FX through the headphones. Am I doing something wrong?
Good tutorial!
there's a way to turn up the headphone on the mixer????
Great tuto thanks a lot
Hey Elias
I have the Behringer Xyenx USB1204 and I am trying to get someone to do a video on how to set it up for youtube videos using a mic such this video you made. Are you able to do a video on that. Step by Step starting from taking the item out the box.
ohh am about to give the mixer away as I have now replaced it with a digital mixer the Presonus 16.0.2, i guess I will have to see what I can do, maybe I will do a last video to cover a lot of questions and request I've had and include your question in that video, I will not be able to cover everything step by step but will see what I can do.
Thank you Elias your time is well appreciated. I am thankful brother.
problem, when I using microfon with Effects, microfon signal with effects going ONLY to MAIN OUTPUTS.
I want used 3outputs same time..
Main outputs -I have mic,with effects
Sub outputs and Room control outputs I have only Microphone signal No Effects! whay?
please help
are the subs 1 & 2 balanced outputs or unbal mono jacks or both. thank you
How do i get this Mixer to work with my Dj Controller...i got the Numark NS7 Dj Controller System i got sound coming out the mixer only problem is i can not record my mix cd together with the mixer cause i got Serato Itch software for my Controler....can you help me to get it to record my normal mix cd..
am not hearing any effects coming through the headphones
I cant get these effects to work I am hearing my plain voice but no effects.
hey mate, sorry for delay please click on the link under the video description, this will take you to the correct download section for your mixers driver.
gat it ,,thankx
I connect my desktop speakers to the phone jack but dont get the effects out loud but when recorded on my computer the effects work just fine. any idea how to send the effects to my speakers?
have you tried switching the source button and see what if it makes a difference? sorry I can't help much because its been good few years now since I had the mixer.
Hate The Mojo plug phones into the main, not phones input.
thanks bro
Is it multitrack?
yesssss
how about compressor..how tu used
+EliasGadgets I don't know if you're still answering these, but is it possible to edit a clip after you record it with the filters and effects? Behringer qx1002usb
+Jeffrey Oden - Yes you can do that, it just depends what daw you use, I would recommend you use the software the comes with the mixer for all your eidting, you have the qx versions so you should have gotten a lot of bundled software made specifically to edit. If you didnt than go onto the website and download them for free.
There wasn't any that came with my mixer. Do you know of some that will allow that? There also wasn't any on the website either
Jeffrey Oden - wow really?? there should have been? here, go below the link and you should see access to the link here you can get all the software - click on downloads and than scroll down origin.behringer.com/EN/Products/QX1002USB.aspx
The only program there was audacity, traktion and podcasting stuff, unless the hosts are programs that's all it came with. Elias Gadgets
what no effect the best for karaoke?
15 or 16
I use 15 , inside 15, I select 3 or 4.
That Camera-moving makes me crazy...maybe post-processing ??? It´s unsupportable...
Please take this as constructive criticism, but maybe you should study up on the effects control a bit before posting. It was obvious that you didn't really know what was going on with the effects/parameter knob. But then again, NEITHER DO I. You fumble around with it as much as I do (with questionable results) but I didn't think I was knowledgeable enough to record a tutorial. I have a 1622 and was hoping to find out how the knob and the TAP button (which you don't even mention) are used to set the effects. Since there's even less information about this in the manual, I'll still keep looking...
I do know, I just wasn't covering them like many things about the mixer I don't go into. I use the effects a lot and also route my own via aux from my inserts with my own fx unit system into the mixer. Thank you and good luck.
Elias Gadgets You should check out how to achieve a proper gain structure anyways. What you are doing in this video is indeed quite questionable.
Would be better if you tune through all the effects one by one instead of talking endlessly about some of your favourite effects.
9:11
Lepo objašnjeno Đoković srbija))))))))))
Drink a tea
Fill video
the sound is not good I am quite disappointed
vietsub vietnam
“Feedback instance” when reading the LEDs? This guy is clueless.
onboard fx sucks tbh.. just run guitar pedals thru fx send
Hello ! Can l mix eho & reverb?