Ubiquiti Radios are certainly the best I have worked with...The problem arises with different changes that create changes Fresnel Effect... I have had three cameras streaming flawlessly and when the weather changes to rain it would drop frequently Currently these radios are as high as we can possible get them mounted...
To maximize gain and throughput, its always better to use directional antennas with very tight focal point vs. unidirectional. Especially when the network will be streaming high def content like 1080p or 4K audio/video (security cams). You also failed to mention signal degradation, which is caused by distance, RF noise, weather, etc.. So, simple saying these radios will work flawlessly over 6 miles when using them for RTP (real time protocol) is a far reach. For moving basic data packets, where latency is not an issue, they would be fine. Moral of the story: Always best to hard-wire cameras.
What do you mean by "directional antenna" vs. "unidirectional"? I thought these Nanostation loco M5 wireless bridges were directional in the sense that their signal is narrowly focused in a 15° angle forward direction? Are you advocating for antennas with a tighter spread?
@@xlrsecurity Basically, you want to keep in mind that the radio listens in all the directions that it also sends a signal. If it's an omnidirectional antenna, it's sending 360* and also listening to everything in a 360* swath. Expect LOTS of noise, especially in the 2.4ghz band. The farther you want to push your signal, the better off you are narrowing your beam, and that can only be done with a dish (or cone or yagi), as opposed to an omnidirectional pole. The midway between these 2 is a panel, which is what the Nanostation is. Panels, dishes, yagis and cones are considered directional antennas. And as far as that goes, 15* is considered fairly wide, not narrow. The Ubiquiti Nano Loco has a ~15* beam spread, so it's not omnidirectional. But it's not as tight as a dish. If you really want to push a signal far, check out Ubiquiti's M2 dish ..if you can find any. They don't make them any more, so you'll have to check eBay. I think the beamwidth on those is 5* or maybe even 3*. That doesn't sound like much, but you can still eye-ball it if you're standing behind the dish. SWith 2 dishes aimed at each other and clear line-of-sight, you can push a useable signal upwards of 8 miles. (and definitely use the "Align antenna" feature to help you maximize the link's aim. Do so on both ends.) But for that kind of distance/performance and unobstructed line-of-sight, you're going to need one end to be up on a ~100' tower or building. You won't get much more than several hundred feet if you're just on top of roofs (unless the 2 houses in question are on mountain peaks).
By default these do not come with an external antenna connection and one would use a rocket M5 however you can add a port since the PCB has 2 IPX connectors on it. Just get a short length IPX to R-SMA bulkhead cable and install it. You will have to drill a hole for the connector between the LAN port and reset button and cut a second notch in the cover for the antenna cable. This would void the warranty but I think these are EOL anyways.
Real-world, I'd be surprised if you get a mile out of those NS Locos, and that's with clear, unobstructed line-of-sight, with one unit up on a ~100' tall pole/building. With NanoStation M2s (with their 16dB antenna instead of the Loco's 9dB), you could get about 1.5 miles. But again, you'd need clear line-of-sight, and nothing in your Fresnel zone (the signal "breathes" as it moves, so your unobstructed line-of-sight is not just laser-straight. You can't have any obstructions in a zone around the beam either). To achieve this kind of unobstructed line-of-sight, at least one end would need to be ~100 feet up above the ground. Weather won't affect it much, but 2.4ghz is really noisy these days, so expect a lot of RF noise, especially if you're in a highly populated area. With a 25dB dish (also from Ubiquiti), you could push that signal out to 10 miles and see much less interference (because of the dish's tighter beam). Been there, done that. (Hundreds of times, actually.)
@@NellysSecurity Thanks for the video - thats really helpful!! By connecting 2 cameras Im assuming you would have both cameras in a range that allows connection to one recorder right? I"m trying to work out a set up for a farm system with 4 cameras in outdoor locations - one in each corner of the farm property looking in. If I understand the set up you have described then I figure I would need a recorder for each camera - does that sound right? Is there another way? Could I use the ubiquity system to return a signal to record footage on a central recorder?
I have a Reolink system using a Reolink NVR. The problem that I am having is that I have IP Cameras on my house and I am wanting to add a camera to my detached garage that is right across the road, (kind of like a side street). There is a clear line of sight from the house to the garage. I know that I could add a router to the garage and connect the camera into the router that is in the garage but then my camera would only be accessible via the web interface, or the Reolink app. I am trying to find a solution to get the garage camera on my Reolink NVR. Would this Ubiquiti product allow the camera to be seen from the NVR? Any informaion that you provide would be grestly appreciated.
What if I don't have a clear line of sight? Like, 1 is near my Internet gateway(My Xfinity Gateway) and the other is down in the garage to where I will mount the security camera?
Can nano station m5 receiver be safe when placed out side the building, i live in remote area, i was advised i can only receive wifi signal when the device is mounted outside the building, is it going to work in wether it rains or after it rains.
Great video! But can you do another on actually connecting the cameras to the receiver step by step? I can't get my Reolink Argus 3 Pro camera to connect to the point-to-point receiver. I know the internet works as I have other things connected already (iPhone, internet gateway, etc.) Does adding a camera require router reconfiguration? Do I need to adjust 2.4ghz vs 5ghz ?? The camera I have is compatible with both frequencies but still not connecting.
I want to use these on property I will be getting in Arizona. What I want to know are they going to be able to withstand the heat of the day as where temps will reach up wards to 120deg F? should I put them in a shroud box with the front opened? the distance is the issue for me I want to put about 9 cameras on my property on the far corners one facing in a North to East and North to West and so on and one camera at the main entrance to the property the run would only be about 1 to 1.25 miles and just running repeaters seems like it would be a PITA and really don't want to deal with running repeaters and all the amps that I would prob need. I would run from a remote location and run them to the House. I plan on having a total of 32 cams in all couple in the barn and other places but those runs would be like no more than 100 feet away. The reason I want so much security is because I will be over 20 miles from anywhere and would like a warning if someone comes on to my property and when someone is driving onto my property. I don't like surprise people just showing up and also since I am so far remote I don't want to be robbed or caught off guard. Since I will have a full off grid home and just the power banks alone will be in the 10's of thousands of dollars, and really nice target for even the batteries alone. I am looking forward to finding the right solution for my security needs Thank you.
Good video. How does it look for multiple cameras at the station end and how does that transfer to the NVR. I have seen countless videos showing the set up at the station end but none showing the set up at the NVR end....would be nice :)
Good Question! You'll assign each camera a unique IP address, which you'll program to each channel on the NVR. That way the NVR knows which camera to talk to on each channel.
Good question! If there is a clear line of sight, and the camera bandwidth stays within 150 Mbps of throughput, then you could use a pair of these radios! Supply is very limited right now, but if you have any further questions, please feel free to reach out to us -> customerservice@nellyssecurity.com / 855-340-9999
Hello... great tutorial.. I have a question please: What if you need to connect 2 transmitters to your receiver? Is it possible or do i need an extra receiver? Thanks
Has anyone had issues with CCTV cameras seem to be causing network to slow , live stream freezes then it s ok then freezes i am running a M5AC rocket and then loco M5 on separate shed each which has a M5 loco (12 sheds ) in each shed i have a 4K camera , Seems like not enough Tx rate but could i be doing soothing wrong ?
For some reason my NVR does not detect the cameras from the other side (cameras are connected to a switch). I checked the ip and it's the same with my router so it's in the same network. The P2P AP and NVR is connected to the router. The P2P is working because I can get internet in the other side. What could be the possible issue?
Thanks Ben! The # of cameras can depend on staying within the 150mbps throughput that these radio can handle! As long as you're within the bandwidth, ive seen installers put 10+ cameras on a single radio. Just be aware of that throughput!
I don't really know the word I'm looking for, but will a single nanostation also work as a reverse access point? Looking for something I can hook to a switch and it will catch a wifi signal and give internet to the wired switch. The nano stations keep showing up in my search for this but don't see anyone using it for this specific reason.
Theoretically that should be possible, but we actually have a few better options for that that are also cheaper. Specifically this guy: www.nellyssecurity.com/tp-link-300mbps-wi-fi-range-extender-re105.html
Hey bud. I am looking to do this kind of setup for my Barn. However I require multiple cameras. Can I simply connect all the cameras to a Switch then pick up each one on the NVR located at the house.
I bought 3 cameras in china and one is a POE style by Samsung….can I use it with your ubiquiti radios? It’s a iPOLIS model SNO-0084RP I do not have camera instructions and do not read Chinese ….help…?
You can use these radios for any data transmission wirelessly over the bridge. Theyre not specifically made for cameras. So as long as your chinese cameras have an RJ45 connection, they should technically be able to talk over these radios. Unfortuantely we cannot help with the chinese cameras you purchased unless you got them from us. You may try ipcamtalk.com for some assistance however!
@@NellysSecurity that’s the best chunk of optimism….I”ll take it…! Yes one has that rj45….the others are coaxial with plus or minus manual zoom leads. Thanks
Great video. I have successfully set one up for a number of cameras. The site has a problem now because they have had a flood and have no internet for the foreseeable future. Since the internet has gone down both Ubiquiti Nanostation M5's have stopped working. Can they not work as a wireless bridge without an internet connection?
the nanostations should still work if they both have power and are pointing at eachother. Id advise ensuring that the units have power and try logging into them via local PC. If you got the nanostations from us, feel free to contact our tech support - customerservice@nellyssecurity.com / 855-340-9999
Hey James, what kind of cameras do you have connected? Wifi 2.4ghz or 5ghz? I can't get my Reolink camera to connect to the point-to-point . Other things do connect ( etc.)soknow the internet is but does a camera addition require router reconfiguration?
Amazing content, If i have a Pair, on the endpoint, I'm I limited to using only 1 cctv on a 4ch POE, or is it possible to add 3 or 4 depending how big my POE swtich is? Do I need more that one pair on the same pole, or is 1 transmitter enough
You can have multiple cams on a single ubiquiti radio! As long as you're within the bandwidth limits, you wont get bottlenecked. Ive seen someone put 20+ cams over a ubiquiti radio network.
@@NellysSecurity what’s the smallest POE switch in your catalog for two cctv cameras (at the end of a drive way) and of course a pair of preconfigured radios….?
Hey Isa! Football Fields are pretty common here in the USA. The rectangular field of play used for American football games measures 100 yards (91.44 m) long between the goal lines, and 160 feet (48.8 m) (531⁄3 yards) wide.
My dilemma is I have three buildings (A,B,C) where A&B are line of sight and B&C are line of sight. A building has trees blocking a clear view of building C. A building is where internet service comes in. How do I transition in B building to C building so I can bridge the entire system? Each building has power and I can run 120 volt outlets for POE.
@@TheKaffeeKlatsch no need to get crazy, see if they link up first. Try the set you have or get first and see if you get signal, then go from there. You can set up the A to B in a temp B to C to see if you get a link and go from there. Good luck. They are simple to work with and YT has plenty of set-up vids.
Hey there! It would depend on how much bandwidth each camera is using. These ubiquiti's can handle 150+ Mbps of throughput. I've seen some installers put 7-9 cams across a single ubiquiti bridge.
@@NellysSecurity 7-9 cams?? What's the frame loss with more than 5 running simultaneously? At lets say a range from 2-4 miles with 7 feeds within the 150 limitation.??
Is it a one to one configuration? Or, can you program a receiver to accept multiple cameras? Say 4 transmitters to one receiver. Looking forward to your response.
Yes, if you purchase the ubiquiti radios from Nelly's, we'll offer support on getting the radios to talk. Please note, we only will provide support on how to bridge the radios together! Any complex or configurations outside of what we advertise these radios for, may not be 100% doable by our tech support.
Hey there, If you check out the spec sheet from Ubiquiti, you can find that the field of width does change with the more distance -> dl.ubnt.com/datasheets/nanostationm/nsm_ds_web.pdf
if you need to cover a wider degrees of coverage than available via one access point, what else can be used to get a larger degree pattern, less directional signal? for example if access point is only visible to stations within a 30 degree field of view, what if want 120 degree coverage?
It depends how far away you get, you cant change the field of view but within a couple of meters you can connect with it no matter which direction you are using them in
@@MikePowlas Yes, you can get a 120* antenna, but considering we're talking about Ubiquiti Loco radios, it's cheaper to set up 2 radios. Better RF performance that way anyway.
Well the PoE injector is not really proprietary as it is 24v standard PoE wiring. The neat thing about the M2 and M5 radios is they will link up to an existing wifi network so you could use these as client stations mounted on a tripod with a laptop to get on wifi networks that were normally too weak for the laptops wifi to use.. If you have a problem with trees in the way the NSM9 is the 900 MHz version and they penetrate better in those types of areas. The NS L 5AC is the drop in replacement for the AP side of a network using these but only in legacy mode
Does someone know if i can see on my phone wifi solar camera at distance 200-300 m with pointed Ubiquiti NanoStation M2, directly connected to my home router?
Hey there, Im not too familiar with a Scout Fisheye. You may try reaching out to the manufacturer or the distributor you purchased it from to see if they can point you in the right direction.
Unfortunately it’s clearly not true. I’m using exactly this model in Hungary as bridge, and the distance is more than 2 km. Link speed is 300/300 solid. There is some drop only if a very heavy rain coming
I own and run a WISP (Wireless Internet service Provider) company, This is some of the equipment that we use to provide internet to homes and businesses.
Joker!!!!! This way it will not work at all giving you headaches. First of all, you have to change the ethernet in order to reach the interface. Dont get it that you guys do believe that everybody has the base knowledge as you. Don't assume that most people do this for the first time This is useless. please make a video starting from the beginning. Also, this equipment has faulty´s that never include in Videos as it is supposed to work because you get paid for it. If you view all these Videos that have been streamed now one shows Failiurs why are so many looking for solutions at Google if this is so easy and has no faults?
Our video is simply a guide for beginners to reference. If you are experiencing possibly faulty issues or need advanced troubleshooting, please reach out to the distributor you purchased the units from for support or RMA.
@@NellysSecurity That is exact what I mean it is not for beginners otherwise you would show how to get realy to the interfaces that is what a beginner needs for a start. The stupid answer go to you supplier is what you get everywehere and they dont reply. So do it right or just forget about it. Im not an avances i go just true this shit
Ubiquiti Radios are certainly the best I have worked with...The problem arises with different changes that create changes Fresnel Effect... I have had three cameras streaming flawlessly and when the weather changes to rain it would drop frequently Currently these radios are as high as we can possible get them mounted...
Hey, Thanks for the video
I’d want to know which ubiquiti product can handle up to 16 cameras within a kilometer
Thank you
oh yes ive used these products they are awesome for camera or internet espeacially the pre configured units
Very interesting, please can this be applied on a DVR or does it work only on NVR
To maximize gain and throughput, its always better to use directional antennas with very tight focal point vs. unidirectional. Especially when the network will be streaming high def content like 1080p or 4K audio/video (security cams). You also failed to mention signal degradation, which is caused by distance, RF noise, weather, etc.. So, simple saying these radios will work flawlessly over 6 miles when using them for RTP (real time protocol) is a far reach. For moving basic data packets, where latency is not an issue, they would be fine. Moral of the story: Always best to hard-wire cameras.
What do you mean by "directional antenna" vs. "unidirectional"? I thought these Nanostation loco M5 wireless bridges were directional in the sense that their signal is narrowly focused in a 15° angle forward direction? Are you advocating for antennas with a tighter spread?
@@xlrsecurity Basically, you want to keep in mind that the radio listens in all the directions that it also sends a signal. If it's an omnidirectional antenna, it's sending 360* and also listening to everything in a 360* swath. Expect LOTS of noise, especially in the 2.4ghz band.
The farther you want to push your signal, the better off you are narrowing your beam, and that can only be done with a dish (or cone or yagi), as opposed to an omnidirectional pole. The midway between these 2 is a panel, which is what the Nanostation is. Panels, dishes, yagis and cones are considered directional antennas. And as far as that goes, 15* is considered fairly wide, not narrow.
The Ubiquiti Nano Loco has a ~15* beam spread, so it's not omnidirectional. But it's not as tight as a dish. If you really want to push a signal far, check out Ubiquiti's M2 dish ..if you can find any. They don't make them any more, so you'll have to check eBay. I think the beamwidth on those is 5* or maybe even 3*. That doesn't sound like much, but you can still eye-ball it if you're standing behind the dish. SWith 2 dishes aimed at each other and clear line-of-sight, you can push a useable signal upwards of 8 miles. (and definitely use the "Align antenna" feature to help you maximize the link's aim. Do so on both ends.)
But for that kind of distance/performance and unobstructed line-of-sight, you're going to need one end to be up on a ~100' tower or building. You won't get much more than several hundred feet if you're just on top of roofs (unless the 2 houses in question are on mountain peaks).
By default these do not come with an external antenna connection and one would use a rocket M5 however you can add a port since the PCB has 2 IPX connectors on it. Just get a short length IPX to R-SMA bulkhead cable and install it. You will have to drill a hole for the connector between the LAN port and reset button and cut a second notch in the cover for the antenna cable. This would void the warranty but I think these are EOL anyways.
how this solution looks with analog camera ?
Real-world, I'd be surprised if you get a mile out of those NS Locos, and that's with clear, unobstructed line-of-sight, with one unit up on a ~100' tall pole/building. With NanoStation M2s (with their 16dB antenna instead of the Loco's 9dB), you could get about 1.5 miles. But again, you'd need clear line-of-sight, and nothing in your Fresnel zone (the signal "breathes" as it moves, so your unobstructed line-of-sight is not just laser-straight. You can't have any obstructions in a zone around the beam either). To achieve this kind of unobstructed line-of-sight, at least one end would need to be ~100 feet up above the ground. Weather won't affect it much, but 2.4ghz is really noisy these days, so expect a lot of RF noise, especially if you're in a highly populated area.
With a 25dB dish (also from Ubiquiti), you could push that signal out to 10 miles and see much less interference (because of the dish's tighter beam).
Been there, done that. (Hundreds of times, actually.)
Hi, I wanna know if I can connect two cameras with just one router and what kind of switch you recommend, thanks
By the way, this video is so great!!
You sure can! Id recommend any over our IPcamPower POE switches -> www.nellyssecurity.com/video-surveillance/installation/poe-switches.html
@@NellysSecurity Thanks for the video - thats really helpful!!
By connecting 2 cameras Im assuming you would have both cameras in a range that allows connection to one recorder right? I"m trying to work out a set up for a farm system with 4 cameras in outdoor locations - one in each corner of the farm property looking in. If I understand the set up you have described then I figure I would need a recorder for each camera - does that sound right? Is there another way? Could I use the ubiquity system to return a signal to record footage on a central recorder?
@@tnt-thisnthat-securityalar8656 this is an issue
Can I connect the second one to router so that I can use WiFi at the remote location?
I have a Reolink system using a Reolink NVR.
The problem that I am having is that I have IP Cameras on my house and I am wanting to add a camera to my detached garage that is right across the road, (kind of like a side street). There is a clear line of sight from the house to the garage. I know that I could add a router to the garage and connect the camera into the router that is in the garage but then my camera would only be accessible via the web interface, or the Reolink app. I am trying to find a solution to get the garage camera on my Reolink NVR. Would this Ubiquiti product allow the camera to be seen from the NVR? Any informaion that you provide would be grestly appreciated.
Absolutely the best video !
What if I don't have a clear line of sight? Like, 1 is near my Internet gateway(My Xfinity Gateway) and the other is down in the garage to where I will mount the security camera?
Would you recommend nano station loco m2 for 5 4mp cameras?
Hi, this video was really helpful. please can I do point to point using ubiquity nano station and tplink radio?
Sir I am work with u ...on site..I like ur work... thanku
Can nano station m5 receiver be safe when placed out side the building, i live in remote area, i was advised i can only receive wifi signal when the device is mounted outside the building, is it going to work in wether it rains or after it rains.
Great video! But can you do another on actually connecting the cameras to the receiver step by step?
I can't get my Reolink Argus 3 Pro camera to connect to the point-to-point receiver. I know the internet works as I have other things connected already (iPhone, internet gateway, etc.)
Does adding a camera require router reconfiguration? Do I need to adjust 2.4ghz vs 5ghz ?? The camera I have is compatible with both frequencies but still not connecting.
if i already have a point to point system for internet can i do the same thing or do i have to use this particular system?
Will the receiver also be able to have a wifi signal ?
I want to use these on property I will be getting in Arizona. What I want to know are they going to be able to withstand the heat of the day as where temps will reach up wards to 120deg F? should I put them in a shroud box with the front opened? the distance is the issue for me I want to put about 9 cameras on my property on the far corners one facing in a North to East and North to West and so on and one camera at the main entrance to the property the run would only be about 1 to 1.25 miles and just running repeaters seems like it would be a PITA and really don't want to deal with running repeaters and all the amps that I would prob need. I would run from a remote location and run them to the House. I plan on having a total of 32 cams in all couple in the barn and other places but those runs would be like no more than 100 feet away. The reason I want so much security is because I will be over 20 miles from anywhere and would like a warning if someone comes on to my property and when someone is driving onto my property. I don't like surprise people just showing up and also since I am so far remote I don't want to be robbed or caught off guard. Since I will have a full off grid home and just the power banks alone will be in the 10's of thousands of dollars, and really nice target for even the batteries alone.
I am looking forward to finding the right solution for my security needs
Thank you.
To 8 camera can I just use to antenna or one will work
Good video. How does it look for multiple cameras at the station end and how does that transfer to the NVR. I have seen countless videos showing the set up at the station end but none showing the set up at the NVR end....would be nice :)
Good Question! You'll assign each camera a unique IP address, which you'll program to each channel on the NVR. That way the NVR knows which camera to talk to on each channel.
@@NellysSecurity Many thanks...my NVR assigns IP addresses for plug and play cameras, presumably I can just use these
Nice. How can 30 cameras on a 4km road be set up?
Good question! If there is a clear line of sight, and the camera bandwidth stays within 150 Mbps of throughput, then you could use a pair of these radios!
Supply is very limited right now, but if you have any further questions, please feel free to reach out to us -> customerservice@nellyssecurity.com / 855-340-9999
If my point to point distance is about 800meters, still need line of sight?
Yes you will. These radios require line of sight no matter the distance between them.
Good day sir, do you have videos regarding tenda radio configuration?
we do not unfortunately
I want a cam in an area where a battery and solar panel must be used, how is a propriety power supply going to be adapted to 12 v?
With an inverter.
Hello, is Ubiquiti Nanostation Loco M5 radios water-resistant? Just in case you want to mount them outdoor?
Yes, They are outdoor rated.
Hello... great tutorial.. I have a question please: What if you need to connect 2 transmitters to your receiver? Is it possible or do i need an extra receiver? Thanks
Thanks Enrique!
You can set the single AP with multiple Stations pointing at the AP! Just be sure you have a clear line of sight between the radios.
@@NellysSecurity Thank you! I appreciate it!
Why the camera connected to a reciever? What if i will install a camera to a remote location?
Has anyone had issues with CCTV cameras seem to be causing network to slow , live stream freezes then it s ok then freezes i am running a M5AC rocket and then loco M5 on separate shed each which has a M5 loco (12 sheds ) in each shed i have a 4K camera , Seems like not enough Tx rate but could i be doing soothing wrong ?
Love u brother. Your video is very useful and important and knowledgefull.
How can I view my IP camera system on two different screens, security office and Manager's office
For some reason my NVR does not detect the cameras from the other side (cameras are connected to a switch). I checked the ip and it's the same with my router so it's in the same network. The P2P AP and NVR is connected to the router. The P2P is working because I can get internet in the other side. What could be the possible issue?
Hey Peter, I'd make sure the radio on the camera side is set to station and is locked to the AP's MAC address. These also need a clear line of sight.
have you used one station for multiple cameras on continuous recording powered by poe switch?
Yes we have! As long as you stay within the Stations bandwidth parameters, you are good!
Can you use at the receiving point instead of a poe switch another wifi router in order to spread your network signal wirelessly?
If you connect the "Station" end to a router, then the router can spread the internet signal that is coming from the "Access Point".
Great video!! how many cameras can I install in the receiver side (on the POE Switch)?
Thanks Ben!
The # of cameras can depend on staying within the 150mbps throughput that these radio can handle! As long as you're within the bandwidth, ive seen installers put 10+ cameras on a single radio. Just be aware of that throughput!
I don't really know the word I'm looking for, but will a single nanostation also work as a reverse access point? Looking for something I can hook to a switch and it will catch a wifi signal and give internet to the wired switch. The nano stations keep showing up in my search for this but don't see anyone using it for this specific reason.
Theoretically that should be possible, but we actually have a few better options for that that are also cheaper. Specifically this guy: www.nellyssecurity.com/tp-link-300mbps-wi-fi-range-extender-re105.html
Hey bud.
I am looking to do this kind of setup for my Barn. However I require multiple cameras.
Can I simply connect all the cameras to a Switch then pick up each one on the NVR located at the house.
yes you can
I bought 3 cameras in china and one is a POE style by Samsung….can I use it with your ubiquiti radios?
It’s a iPOLIS model SNO-0084RP
I do not have camera instructions and do not read Chinese ….help…?
You can use these radios for any data transmission wirelessly over the bridge. Theyre not specifically made for cameras. So as long as your chinese cameras have an RJ45 connection, they should technically be able to talk over these radios.
Unfortuantely we cannot help with the chinese cameras you purchased unless you got them from us.
You may try ipcamtalk.com for some assistance however!
@@NellysSecurity that’s the best chunk of optimism….I”ll take it…!
Yes one has that rj45….the others are coaxial with plus or minus manual zoom leads.
Thanks
Does it come with 1 or two radios as you need to have a transmitter and receiver
We sell them individually on our site. So if you are needing a pair, you will have to get 2 single radios.
This Antenna supports me 12 cameras in the network to transmit it at a distance of 500 meters?
If you stay within the bandwidth parameters of the radios and have a clear line of sight between them, you should be good!
Great video. I have successfully set one up for a number of cameras. The site has a problem now because they have had a flood and have no internet for the foreseeable future. Since the internet has gone down both Ubiquiti Nanostation M5's have stopped working. Can they not work as a wireless bridge without an internet connection?
the nanostations should still work if they both have power and are pointing at eachother.
Id advise ensuring that the units have power and try logging into them via local PC.
If you got the nanostations from us, feel free to contact our tech support - customerservice@nellyssecurity.com / 855-340-9999
Hey James, what kind of cameras do you have connected? Wifi 2.4ghz or 5ghz? I can't get my Reolink camera to connect to the point-to-point . Other things do connect ( etc.)soknow the internet is but does a camera addition require router reconfiguration?
Amazing content, If i have a Pair, on the endpoint, I'm I limited to using only 1 cctv on a 4ch POE, or is it possible to add 3 or 4 depending how big my POE swtich is? Do I need more that one pair on the same pole, or is 1 transmitter enough
You can have multiple cams on a single ubiquiti radio! As long as you're within the bandwidth limits, you wont get bottlenecked. Ive seen someone put 20+ cams over a ubiquiti radio network.
@@NellysSecurity what’s the smallest POE switch in your catalog for two cctv cameras (at the end of a drive way) and of course a pair of preconfigured radios….?
Need to install a camera in my barn ,will this work on minus 40 weather?thanks
The operating temperature of the ubiquiti radio is -22F to 167F
Imagine using a football field as a measurement guideline
Hey Isa!
Football Fields are pretty common here in the USA. The rectangular field of play used for American football games measures 100 yards (91.44 m) long between the goal lines, and 160 feet (48.8 m) (531⁄3 yards) wide.
Hello, do trees get in the way of the connection?
If for example, I have a lot of trees in the line of sight, would it still work?
The signal can degrade quite fast if there is not a clear line of sight. Trees in the way can prohibit the radios from working effectively.
Do you install a nvr or a dvr at the statoin receiver side or at the access point side?
Access point at the NVR side, station at the camera side.
Good video! You know that they both send and receive data. A transmitter and a receiver doesn't define what they really are.
My dilemma is I have three buildings (A,B,C) where A&B are line of sight and B&C are line of sight. A building has trees blocking a clear view of building C. A building is where internet service comes in. How do I transition in B building to C building so I can bridge the entire system? Each building has power and I can run 120 volt outlets for POE.
You would need to create 2 bridges using 4 units. A to B then B to C.
@@unoefxz That's what I thought. I guess I'll find out once I get to the site if A to C connects well. Chainsaw might come into play.
@@TheKaffeeKlatsch no need to get crazy, see if they link up first. Try the set you have or get first and see if you get signal, then go from there. You can set up the A to B in a temp B to C to see if you get a link and go from there. Good luck. They are simple to work with and YT has plenty of set-up vids.
@@TheKaffeeKlatsch ps:just take note of ip addresses etc. I write em inside the covers in case I forget.
@@unoefxz Fortunately I have four units because I have a secondary location to connect as well. It'll get figured out, thanks for your response.
i have 4 port poe switch on my ubiquiti but my camers are on the same ip
How many camera feeds can we send using this system?
Hey there!
It would depend on how much bandwidth each camera is using.
These ubiquiti's can handle 150+ Mbps of throughput.
I've seen some installers put 7-9 cams across a single ubiquiti bridge.
@@NellysSecurity 7-9 cams?? What's the frame loss with more than 5 running simultaneously? At lets say a range from 2-4 miles with 7 feeds within the 150 limitation.??
Is it a one to one configuration?
Or, can you program a receiver to accept multiple cameras?
Say 4 transmitters to one receiver.
Looking forward to your response.
Yes you can have 1 Access Point and multiple stations in a configuration!
@@NellysSecurity I need your help
Well done!
Do you also have a tech support team that will help you configure the network protocols for beginners?
Yes, if you purchase the ubiquiti radios from Nelly's, we'll offer support on getting the radios to talk. Please note, we only will provide support on how to bridge the radios together! Any complex or configurations outside of what we advertise these radios for, may not be 100% doable by our tech support.
Is there a way to connect these to a Verizon Jetpack, my source of internet access?
Please contact our support for assistance.
as you increase distance from access point what is the field of width that station radios can occupy and still communicate with the access point?
Hey there,
If you check out the spec sheet from Ubiquiti, you can find that the field of width does change with the more distance -> dl.ubnt.com/datasheets/nanostationm/nsm_ds_web.pdf
Can 4 cameras goes into a switch and be transmitted to an NVR at a distance like 300m apart, which should be AP and which should be Station PtP ?
yes that works. AP can be located where you have your main network, Station will be where you have the cameras.
Can I use that to transfer my fiber optic ISP from another island across the sea 25km away?
You will have to use different radios from unifi but yes it is possible if you have clear line of sight.
Powerbeams will get that job done. I own a WISP company and have many long shoots.
if you need to cover a wider degrees of coverage than available via one access point, what else can be used to get a larger degree pattern, less directional signal?
for example if access point is only visible to stations within a 30 degree field of view,
what if want 120 degree coverage?
It depends how far away you get, you cant change the field of view but within a couple of meters you can connect with it no matter which direction you are using them in
You can get a 120 AP radio.
@@MikePowlas Yes, you can get a 120* antenna, but considering we're talking about Ubiquiti Loco radios, it's cheaper to set up 2 radios. Better RF performance that way anyway.
@@MikePowlas Yup the 120 works great, have used it many times for camera on different buildings
Rocket M5 with wider lobe antennas
Can I use 2 antena to send to one because I have to install 8 but I don’t not if one antena can take the load of 8
as long as you don't exceed the bandwidth limitation you can send stream from multiple antennas to 1 receiver.
Yes it is called PTMP We do it all the time to provide internet to homes and businesses.
Well the PoE injector is not really proprietary as it is 24v standard PoE wiring.
The neat thing about the M2 and M5 radios is they will link up to an existing wifi network so you could use these as client stations mounted on a tripod with a laptop to get on wifi networks that were normally too weak for the laptops wifi to use..
If you have a problem with trees in the way the NSM9 is the 900 MHz version and they penetrate better in those types of areas.
The NS L 5AC is the drop in replacement for the AP side of a network using these but only in legacy mode
Can you connect it to an NVR
You sure can!
I did not see your preconfigured loco 5s…?
We have since dropped that SKU unfortunately. Our tech support can still program them for you if you buy them from us!
@@NellysSecurity I want a pair
Please provide a SKU
And any support added costs
Thank you
Ray
can I connect 24 IP camera wit it
If you stay within the 150Mbps of throughput, then technically yes!
Does someone know if i can see on my phone wifi solar camera at distance 200-300 m with pointed Ubiquiti NanoStation M2, directly connected to my home router?
I would advise putting a radio at each end of the bridge. You do need a clear line of sight. That 200-300m distance is no issue with these radios.
@@NellysSecurity Thanks a lot! I have a house as an obstruction between my house and the pole.
Helpful... 👍
Nice
Sir, How can configure scout fisheye IP camera?
Hey there, Im not too familiar with a Scout Fisheye. You may try reaching out to the manufacturer or the distributor you purchased it from to see if they can point you in the right direction.
It's helpful but way over simplification. Nothing to do with setting up networking & video is that easy or secure.
autolike 👍🏻
These devices distance range is not more than 500m by the way
Unfortunately it’s clearly not true. I’m using exactly this model in Hungary as bridge, and the distance is more than 2 km. Link speed is 300/300 solid. There is some drop only if a very heavy rain coming
Can it be used for sharing internet
Yes it can!
I own and run a WISP (Wireless Internet service Provider) company, This is some of the equipment that we use to provide internet to homes and businesses.
Ketane me milega
No security.... ahhh
Jackson Patricia Johnson Jessica Johnson Eric
20
Aela
Joker!!!!! This way it will not work at all giving you headaches. First of all, you have to change the ethernet in order to reach the interface. Dont get it that you guys do believe that everybody has the base knowledge as you. Don't assume that most people do this for the first time This is useless. please make a video starting from the beginning. Also, this equipment has faulty´s that never include in Videos as it is supposed to work because you get paid for it. If you view all these Videos that have been streamed now one shows Failiurs why are so many looking for solutions at Google if this is so easy and has no faults?
Our video is simply a guide for beginners to reference. If you are experiencing possibly faulty issues or need advanced troubleshooting, please reach out to the distributor you purchased the units from for support or RMA.
@@NellysSecurity
That is exact what I mean it is not for beginners otherwise you would show how to get realy to the interfaces that is what a beginner needs for a start. The stupid answer go to you supplier is what you get everywehere and they dont reply. So do it right or just forget about it. Im not an avances i go just true this shit