Good day, thank you for putting out time to tutor us, we do appreciate it. Please i have a question for you. How do i connect multiple external microphone to my dahua DVR which have one input for audio source. I want to use cat 5 or 6 cable to connect all camera and mic into the DVR. I have three (3) cameras with built in mic and two external microphone. So how do i link all these mic into the one source audio input on the DVR. Eagerly to hear from you in anticipation. Thank you.
Nice video but it's incomplete because you need to show and explain how to setup the AP and the Station because we have young Technicians who just finish school and this kind of video will be a very help for them.
Congrats for your amazing contents..one thing i would like to ask though its out of the topic,IS ,can i use the same bridges demonstrated in this video to extend wireless internet connectivity from my router to connect 2 buildings that are 400m apart ?
I have two buildings, both are 750 meters apart from each other. I use this setup for internet connection by setting up access point and station. Is it possible to use it for both internet and connecting to cctv at the same time?
What if i already have that setup. Then i want to add another acces point. Do i have to setuo another pairs of accespoint and station. Or i just need to buy accespoint and connect it to existing station
Great work. But i need to ask, what if i'm setting up Wireless Cameras power via power adaptors? can i go through the same process? I'd also want to ask something about Intercom. Is there a way i can use a switch in the setting up of Intercom??
1. Wireless bridges don't transmit power over Ethernet. You need a localised power for powering the cameras 2. No, you can't use a switch for Telephone intercoms, unless for Voice over IP (VoIP). I hope to cover VoIP later.
@@Tech_Inside_OutQt1. I meant how do I extend the wireless range from the camera to the NVR? The type of camera I use have an NVR which is also wireless and has 1 WAN port. So I'm asking if i can implement the range (signal) extension with these Tenda CPEs
Typical example: 8 channel cameras, 4 installed in shop1 and 4 installed in shop2. the distance between these two shops is about 100meters. the NVR is stationed in shop1
Good day, thank you for putting out time to tutor us, we do appreciate it. Please i have a question for you. How do i connect multiple external microphone to my dahua DVR which have one input for audio source. I want to use cat 5 or 6 cable to connect all camera and mic into the DVR. I have three (3) cameras with built in mic and two external microphone. So how do i link all these mic into the one source audio input on the DVR. Eagerly to hear from you in anticipation. Thank you.
Nice video but it's incomplete because you need to show and explain how to setup the AP and the Station because we have young Technicians who just finish school and this kind of video will be a very help for them.
Well noted
You've made it so simple. Thank you
Thank you too
This is great video, this can replace OFC where there is no much building interference. Can this setup replace OFC in this scenario?
Thanks for appreciating the Video.
Congrats for your amazing contents..one thing i would like to ask though its out of the topic,IS ,can i use the same bridges demonstrated in this video to extend wireless internet connectivity from my router to connect 2 buildings that are 400m apart ?
Yes, you can
The installation wasn't verified
Thanks for this video, it's so helpful. Please, how can I connect multiple bridges to one nvr?
Its possible, i will try and explain in a tutorial. Stay tune for that video
I have two buildings, both are 750 meters apart from each other. I use this setup for internet connection by setting up access point and station. Is it possible to use it for both internet and connecting to cctv at the same time?
Yes, you can do that.
Thanks
Can you do a video about configuring the CPEs?
Well noted
Good video now make a video with multiple client cpe connected to access point(controller) where they use point to multipoint😅
Well noted
how do we configure both APs..
It goes through a series of processes, i may have to produce a video on how it is done
Thank you very much sir
Most welcome
What if i already have that setup. Then i want to add another acces point. Do i have to setuo another pairs of accespoint and station. Or i just need to buy accespoint and connect it to existing station
You can add up to the existing ones by pairing the new one to the old.
@@Tech_Inside_Out add more acces point. Linking to one station. Or do i have to setup stations for every acces point. Thank you
is it possible to install this vertically? instead of horizontal position. i was planning to install it in the elevator shaft. thanks
You can place it both ways, vertical or horizontal
Great work. But i need to ask, what if i'm setting up Wireless Cameras power via power adaptors? can i go through the same process?
I'd also want to ask something about Intercom. Is there a way i can use a switch in the setting up of Intercom??
1. Wireless bridges don't transmit power over Ethernet. You need a localised power for powering the cameras
2. No, you can't use a switch for Telephone intercoms, unless for Voice over IP (VoIP).
I hope to cover VoIP later.
@@Tech_Inside_OutQt1. I meant how do I extend the wireless range from the camera to the NVR? The type of camera I use have an NVR which is also wireless and has 1 WAN port. So I'm asking if i can implement the range (signal) extension with these Tenda CPEs
Typical example: 8 channel cameras, 4 installed in shop1 and 4 installed in shop2. the distance between these two shops is about 100meters. the NVR is stationed in shop1
@@deSpotLightTV For the camera range, you can't extend.
typical camera type is the Tenda Full Color Wireless Kit
is it possible if there are trees or buildings blocing it?
It penetrates through
Does means that i will be using networks cable to connect camera in that distance of 10km
No, the 10 km is what would be covered using the wireless connection through the CPE or wireless bridge
How can we connect these two bridges?
@hamissouyacoubaissihaka8907 I hope to do a comprehensive video on how to connect and push signal through the bridges
Pls which cpe can cover up to 20klm
I don't have the model numbers off head, i would have to check and get back to you.
Thank you so much for your job
You are very welcome
Thank you!!!
You are welcome
How do we get power from the station point
You must find a way out.
Can this only work with IP cameras ?????
No, you can use it for AHD cameras as well
you are more than Good
We thank God
You need an allowance from the state - government to send with such a strenght !
🙏
You're the best
I give God thanks, who gives the wisdom
Do you know any device or CPE that can carry 16 cameras within a km
As you rightly mentioned, a CPE can do that. You can place the cameras on a switch and fed into the CPE
@@Tech_Inside_Out I’m have been using cpes but non is able to transmit up to 16 cameras
How can one configure these device
Please watch the video, i showed the pairing
Thank so much
You are welcome
Good job.
Many many thanks
How I wish I can come over for a physical training/couching.
@usmanbrah7175 You can come, I live in Accra Ghana. Are you resident in Ghana?
Thank you
Thanks very much
This is great video, but the installation wasn't verified
Thanks for your observation, I will find time and do a simulation video on this .
anyone can i ask this the offline or need inthernet?
It can be used offline
Tq bro nice vid
Thanks
Nice
Thanks very much
how many camera's can connect trough p2p device?
It varies from one manufacturer to the other but it is done mostly through remote view sharing after linking the first mobile.
Please Tell me the model number
I did this video for quite a long time now and i would have to go back and check from the shop for the details fir you
@@Tech_Inside_Out ok thanks 🙏🙏
I'm
.