Repairing Daikin UF Error
Вставка
- Опубліковано 3 жов 2024
- This fault was caused by a faulty outdoor Printed Circuit Board. In this video I replaced the PCB and the outdoor fan motor which was also on its way out.
Below I have listed the Tool Bag and Tools that you see me use personally in my videos. By using these links it doesn’t cost you anymore however by doing so you are helping the channel grow.
Thanks for the support!
MILWAUKEE BACKPACK (I use this backpack as my Service Bag).
www.amazon.com...
FLUKE HVAC MULTIMETER KIT
www.amazon.com...
KLEIN (MEGGER) CONTINUITY INSULATION TESTER
(This isn’t the megger I use personally because the one I use is old and isn’t available anymore. I recommend this one because its similar and does the same thing).
www.amazon.com...
VESSEL ELECTRIC SCREWDRIVER
www.amazon.com...
KLEIN CABLE STRIPPERS
www.amazon.com...
FIXINGS I USE FOR CONDENSING UNIT BRACKETS
www.amazon.com...
KNIPEX INSULATED LONG NOSE PLIERS
www.amazon.com...
KNIPEX INSULATED SIDE CUTTERS
www.amazon.com...
PENCIL
www.amazon.com...
RATCHETING RIGHT ANGLE SCREW DRIVER
www.amazon.com...
FIELDPIECE PIPE CLAMP THERMOMETER
www.amazon.com...
You are 100% correct on replacing the fan motor. Mitsubishi has a similar setup on one of their models where the board is upside down abs you have to be a contortionist to see the blink code. Great job stay well.
Thanks again mate. They definitely don’t make it easy for you do they! Haha
Great video and good point regarding replacing the motor that was obviously on the verge of failure. BTW, how long did you spend making the repair vs time spent making & editing video?
they do it that way so the IPM ang IGBt gets cooling from the fan
Great job 👏...from where you get the parts ?
you are great technician
Thanks mate!!
You did good changing the fan motor too. If it was my own, out of warranty, I might see how much longer I could get out of it. But I’d always have a spare sitting in the box ready to go.
Thanks mate
Well done Mitchel, that old saying, if its worth doing do it well 👍
That’s the motto! Thanks mate
Ok forgot to mention that used way too much thermal paste, obviously you've never read or researched how to do heatsinks. watch a video of how to install thermal paste on processors. That board won't last long if thermal paste all over it and they make thermal paste remover/cleaner, then you use the primer on both surfaces.
Thanks mate
Yes replace fan, take blade off turn with fingers if it feels notchey or tight it’s cactus shaft should spin a few revs when flicked with fingers
Thanks
Good job broo..
Cairr😊
That’s bro 👊🏻
See, you're using 5 change outs worth of thermal paste 😅
I’m a generous guy what can I say lol
Hey mate where can we order this board we have the same error
Hey mate, you can get it from Daikin spares directly or any air con company.
U can actually replace the motor bearings on those fans as well as on the Samsung motors
Dead right changing the FM. You can clearly see the new one rotates alot easier than old one.
Thanks mate!
Nice video! I don't like the grille they have, the old one would've looked much better.
Thanks mate. Yeah I think they put it on so a kid can’t climb up and fall off the balcony.
@@maracservices Okay. Safety is a higher priority over style if kids are around constantly.
@@zanelancaster2007 I’m pretty sure it’s actually a requirement here in Australia for new builds. So unfortunately if the unit is on a balcony close to the edge, you need to modify it. Thanks mate
@@maracservices Ahh okay. I think my family needs to change that soon...
Why do all that work and not even clean the fan blade? You're already putting a strain on a new motor. "Typical Lazy tech" would've taken 10 minutes to clean fan & spray condenser coils with water from inside unit out while all covers are off.
Thanks mate
Oh give it a rest hero. That tiny amount of dust on the fan blade is not going to strain the motor and the coil is spotless.
You always do pointless work for free?