how to control 1 servo and 1 dc motor using l293d motor shield at same time. I watch many video on l293d shield but in all video different motor not run at same time . For example if there is a code for dc motor than you can run only 4 dc motor. If there is a code for servo motor you can run only 2 servo. But I want to run servo and dc motor together using l293d motor shield. So sir please provide me code for running two different motor ie..Servo and Dc motor same time.
I chose this tutorial because it is easy to understand and it slowly points to the different parts I liked because we also understood better how to use a motor shield and for me it was a huge help.
Sir how to use the digital pins after placing motor shield on arduino. I am currently working on my final year project which is a fire fighting robot and when I put the motor shield on arduino then the digital pins are also covered . Do I have to perform soldering on motor shield
Hello congratulations for sharing. I have a roue codeuse on the motor shaft (recovered from a printer).I did the test of 5v pulses sent by the transistor. Could you specify where I have to connect these pulses on the arduino motor shield. Thank you.
The board has ONE configurable component - the PWR jumper - and it isn't mentioned!When the jumper is installed power is supplied from the Arduino 9v supply. The plug for this supply is visible in the video, below the motor shield, when the motor is operating. When the jumper is removed power is supplied from the motor board +M terminal. This is the recommended mode of operation if using multiple motors or servos. Do not leave the jumper installed if both power supplies are connected: there are no isolating diodes.The description of the LED is unintelligible.
Nice explanation. I have one doubt. Why you have given power supply to Arduino board but not to motor shield? What if I power the arduino by usb and connect the power supply to motor shield? What if I power the motor shield only and not connect the usb?
Great video! I am making a ball launching machine using a 12V 30W motor and a 16.8 Ah Lithium battery. Would this motor shield work with this setup? If not, what's your recommentation? Thanks
I liked this video very much and usefull can you put the video of how can we connect hc 05 in arduino and motor driver shield for rotaiting the dc motor
why do I get the following error: call to 'AF_DCMotor::AF_DCMotor(uint8_t, uint8_t)' uses the default argument for parameter 2, which is not yet defined Has AdaFruit changed their library? Any information would be gratefully received.
OK. Sorted. There has been a change in the software. A sketch for my 2 year old obstacle avoiding robot works and it was compiled 2 years ago with the line : AF_DCMotor motor1(1); but this same line fails now. Using the lines: AF_DCMotor motor1(3,2); AF_DCMotor motor2(4,2); compiles and works on my grandson's tank. I suppose the second parameter is useful but since Adafruit don't support the board I can't see many people not being caught out by it.
Thank you for this. But it doesn't explain why a sketch, even Adafruit's own examples, now fail to compile. Whereas they always used to, without the second parameter. I am not very good at coding so I don't have much time for sketches/programs that don't work. Nor do I understand the complexities of .h and .cpp files so I have to rely on expert advice and I am very thankful for it!
Как подключить шаговый мотор от сканера что-бы он играл музыку как на youtube канале floppotron? स्कैनर से स्टेपिंग मोटर को कैसे कनेक्ट करें ताकि वह यूट्यूब चैनल फ्लॉपोट्रॉन की तरह संगीत बजाए? How to connect the stepping motor from the scanner so that he plays music like on the youtube channel floppotron?ff
+leeladharesh leela no you cannot. Buy a L293D board. Robodo Electronics L298 Motor Driver Module www.amazon.in/dp/B00N4KWYDE/ref=cm_sw_r_cp_apa_i_YzPAAbTXP8F44
Arduino: 1.8.10 (Windows 7), Board: "Arduino/Genuino Uno" sketch_nov16a:1:9: error: AFMoter.h: No such file or directory #include ^~~~~~~~~~~ compilation terminated. exit status 1 AFMoter.h: No such file or directory This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
Hi bro i really need your help can u please share your email id actually i have my project in which i have to make a robot with a gripping so i have already made the base and now i have to install the gripper my gripper has 2 Servo and 1 dc motor and my car gas 4 motor i want to control all of them from my mobile with Bluetooth and need help with codes please bro please help me out
Works well, thought I had it wrong then realised that I hadn’t put jumper for power. A good teaching video
How did you solder header pins on the motor driver shield ? Please reply project pending
how to control 1 servo and 1 dc motor using l293d motor shield at same time.
I watch many video on l293d shield but in all video different motor not run at same time .
For example if there is a code for dc motor than you can run only 4 dc motor. If there is a code for servo motor you can run only 2 servo.
But I want to run servo and dc motor together using l293d motor shield.
So sir please provide me code for running two different motor ie..Servo and Dc motor same time.
I chose this tutorial because it is easy to understand and it slowly points to the different parts I liked because we also understood better how to use a motor shield and for me it was a huge help.
is there any specification to connect motor wires to audrino? ie. black and red can it be any order?
when i put off cable from arduino ...the code dose not work with motor control shield,even i connect external 18 volt bettry to the ardunio
Why do you use the power jack? Is it to powe the motor because it draws way too much current and arduino can not handle?
is it okay if my H Bridge is not on the top of the arduino?
If I would use two servos and I give power to Arduino with the USB, can I use a battery pack to power the servos ?
Sir how to use the digital pins after placing motor shield on arduino. I am currently working on my final year project which is a fire fighting robot and when I put the motor shield on arduino then the digital pins are also covered . Do I have to perform soldering on motor shield
Pls can u tell me how i connect mpu 6050 with motor shield
If we have 2 motors one work with 12v and the other one with 9 v how can we use the shield
Hi I want to connect 4 12 volt gear motor. Which batter I can use for it
Hello sir my ardrino shield start making beep sound and gives very less power that even can't run the motor plz help
I have KA03 motorshield is the code compatable for my shield?
Hello congratulations for sharing. I have a roue codeuse on the motor shaft (recovered from a printer).I did the test of 5v pulses sent by the transistor. Could you specify where I have to connect these pulses on the arduino motor shield. Thank you.
How to use it with joystick?
What is PWR in motor shield
The board has ONE configurable component - the PWR jumper - and it isn't mentioned!When the jumper is installed power is supplied from the Arduino 9v supply. The plug for this supply is visible in the video, below the motor shield, when the motor is operating. When the jumper is removed power is supplied from the motor board +M terminal. This is the recommended mode of operation if using multiple motors or servos. Do not leave the jumper installed if both power supplies are connected: there are no isolating diodes.The description of the LED is unintelligible.
Why the additional power supply is connected to the arduino and not to the shield ?
Nice explanation. I have one doubt. Why you have given power supply to Arduino board but not to motor shield? What if I power the arduino by usb and connect the power supply to motor shield? What if I power the motor shield only and not connect the usb?
sir i want please upload, how to connect hc-05 bluetooth to arduino uno,i had totally confused.
Very good. I`m still a beginder but I got my motor to spin. I´m happy thank you.
Bro please help me ma code upload krne ke bad bhi nahi chal rhi ak bhi gear motor
If you have to attach some jumper wires to Arduino how you can connect wire with Arduino.
Only digital pin 2 can be used. You can solder a header pin in the given hole in the motor shield.
May i ask what are the pin input in M1 and M2
Maximum amps that the shield board can transmit is ??
how to know (max) input motor shield and output....im stp help me!!!
Great video! I am making a ball launching machine using a 12V 30W motor and a 16.8 Ah Lithium battery. Would this motor shield work with this setup? If not, what's your recommentation? Thanks
I want to use other digital pins in arduino how to use it and the motor shield on arduino
Bro which wires are those please someone asnwer
u shud talk about the code too, as what those lines do and what are possible lines of code tht is impportant to remember?
Much easier than using an L298N bridge. Shukria.
IT GIVES A BASIC IDEA THANK U A LOT
not getting enough power from motor shield to drive my motor. how to get more power output from motor shield ?
How did you power the motor shield and Arduino
Please help brother,
my dc motor is not working using this af motor shield.
neither mine
Bro can you give link of motor driver A0-A5 you're inserted pins please bro
what is the motor used
It is so very much helpful thank you so much Sir.
Very useful video.......Shyam.......👍👍
Plz make HD video video I can't see programing
I liked this video very much and usefull can you put the video of how can we connect hc 05 in arduino and motor driver shield for rotaiting the dc motor
Can you demostrate wit Pro MINI pllease?
can I contol the speed of DC motor with Arduino pwm by simulink(MATLAB)
Hi sir I am watching video tutorial is awesome or resolve my half problem but how to connect with Bluetooth app
HAVE YOU GET SOLUTION OF YOUR PROBLEM?
I too would like to know that solution!!!
why do I get the following error:
call to 'AF_DCMotor::AF_DCMotor(uint8_t, uint8_t)' uses the default argument for parameter 2, which is not yet defined
Has AdaFruit changed their library?
Any information would be gratefully received.
OK. Sorted. There has been a change in the software. A sketch for my 2 year old obstacle avoiding robot works and it was compiled 2 years ago with the line :
AF_DCMotor motor1(1);
but this same line fails now.
Using the lines:
AF_DCMotor motor1(3,2);
AF_DCMotor motor2(4,2);
compiles and works on my grandson's tank. I suppose the second parameter is useful but since Adafruit don't support the board I can't see many people not being caught out by it.
+Treereaver Jones The second parameter is for frequency (speed of the control signal)
Thank you for this. But it doesn't explain why a sketch, even Adafruit's own examples, now fail to compile. Whereas they always used to, without the second parameter. I am not very good at coding so I don't have much time for sketches/programs that don't work. Nor do I understand the complexities of .h and .cpp files so I have to rely on expert advice and I am very thankful for it!
how to use the other digital pins in DK electronics motor shield
+Umesh Talekar You can use the Digital Pin 2. Just Solder a single male header pin in the given hole.
Как подключить шаговый мотор от сканера что-бы он играл музыку как на youtube канале floppotron?
स्कैनर से स्टेपिंग मोटर को कैसे कनेक्ट करें ताकि वह यूट्यूब चैनल फ्लॉपोट्रॉन की तरह संगीत बजाए?
How to connect the stepping motor from the scanner so that he plays music like on the youtube channel floppotron?ff
Sir i need help when im useing AFMotor code it is not working king
what pins from Arduino Uno do the motor shield use.i want add some other components leaving the pins used ???
+leeladharesh leela you can use the digital pin 2
I wanted to use the LCD display. so can I do it with which pins...
+leeladharesh leela no you cannot. Buy a L293D board.
Robodo Electronics L298 Motor Driver Module www.amazon.in/dp/B00N4KWYDE/ref=cm_sw_r_cp_apa_i_YzPAAbTXP8F44
can I use this motor shield for quadcuptar mini brushless motor
+Creative Bong Nope! You should use an ESC (electronic speed controller)
motorshield is not working when I connect arduino
Ye btao steper or dc ko ek sath kase chlaye code
Bro , how to avoid thermal failure ?
Great video, it was really helpful!
Can i connect bluetooth hc05 to the arduino with this motor shield?
WHAT HAVE U DID OF YOUR PROBLEM
How to setup pins for 4 motors
With arduino nano
What means if led doest not turn on when I connect the af motor shield with. Arduino .. please reply me fast bro
+Mechanic 27 Connect it as shown in the video.
What type of motor shield did you use?
How much power supply??
love you-you have fixed all my problems in life.
Ok, so what is the minimum voltage I can apply to the shield?
Anywhere from 7-24V.
GREAT tutorial works great.
Invaluable info, thanks very much
Thank you for the video!
i tried this but had no luck :( "avrdude: ser_open(): can't open device "/devttyACMO": no such file or directory"
+Junior Cabrera Select the correct COM port.
same here
pokemon pekka busters you have to manually change the setting in the arduino ide in the port tab
Thanks, good job, make sure that you motor does not pull more than 0.6 A
Awesome tutorial! can the board drive more than one dc motor
Great video, worked first go
Bro I am getting 'the system cannot find the file specified' error what to do
+TD channel Try extracting the library zip file and put in the Libraries folder.
Worked awesome thanks!
Apne mere quest ka answer kyo nahi dia
Thank you very much, managed to power 4 dc motors and got the bot running fine
same here
.
I want to ask doubt can you please give me ur contact number
Falliant quelnath can you tell me how did you power your arduino and motor shield?
Great Working well . How to control code for 4 dc motor . Copy and paste and change motor no .
Please help for 4 axis robot . How to remove loop
thanks man its working good
Arduino: 1.8.10 (Windows 7), Board: "Arduino/Genuino Uno"
sketch_nov16a:1:9: error: AFMoter.h: No such file or directory
#include
^~~~~~~~~~~
compilation terminated.
exit status 1
AFMoter.h: No such file or directory
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
It's #include
how to control power window motor using motor shield
Very useful, thanks.
how to connect 4 motor with arduino nano & how this code
Rakib Sarkar You can use a ULN2003 IC with arduino nano or you can use a l293D or l298 motar driver.
Thank you sir..excellent workingg,
Just brilliant
Can you sell this channel.. because you active...🙏🙏🙏
Not active
Please reply for that
very good helpful thank you
nice video bro
how to connect 4 motor with arduino nano
Excellent
not working
Hi bro i really need your help can u please share your email id actually i have my project in which i have to make a robot with a gripping so i have already made the base and now i have to install the gripper my gripper has 2 Servo and 1 dc motor and my car gas 4 motor i want to control all of them from my mobile with Bluetooth and need help with codes please bro please help me out
My email id is samarthminocha3@gmail.com
Thanks u so much buddy
Thank you sir..
ui ken control za motas...
Thanq so much bhaya
We love u so much
You have helped me so much
My friend is very, very good projet vidéo
👍👍👍👍
thank you so much
Please somebody help me
Thank you sir
it works
I want to ask doubt can you please give me ur contact number