Arduino Bluetooth control car with Front & Back Lights using Arduino UNO, L293D Motor Driver, HC-05
Вставка
- Опубліковано 25 лис 2020
- Hello Guys in this Video Tutorial I am going to show you How to make DIY Arduino Bluetooth control car with Front and Back lights at Home
Code is Included.
Grab the Great deals in Next PCB Mid Summer Sale:
www.nextpcb.com/midsummer-sal...
Subscribe It's Free / @makediy9
Schematics, App, Arduino Code: circuitbest.com/c/dHk0t
Enjoy Guys :)
Note: You must detach Bluetooth Module before uploading the code to the Arduino.
Things Needed to Make DIY Bluetooth remote control car with lights:
Amazon.in Links:
Arduino UNO: amzn.to/31sEgU4
TT Gear Motor: amzn.to/2FLFeTF
65MM Wheels for TT Motors: amzn.to/31rrghv
HC-05: amzn.to/37G9fzQ
18650 Battery: amzn.to/34hsldt
2S, 18650 Battery Holder: amzn.to/2TdA1XY
L293D Motor Driver: amzn.to/3dRU9s6
Switch: amzn.to/3dSMREx
Jumper Wire: amzn.to/2HqWHBb
Soldering Iron: amzn.to/2HldvtF
Glue Gun: amzn.to/3mcr51m
Samsung 18650 Battery: amzn.to/2V4CvZE
10MM RED LED: amzn.to/3m88cxb
8MM White LED: amzn.to/3nYpywL
180R Resistor: amzn.to/3lc6KIC
Double Sided Tape: amzn.to/3nYrwgD
Wire for Motor Connection: amzn.to/3ld1Lax
Amazon US Links:
Arduino UNO R3: amzn.to/2SuROJC
TT Gear Motor: amzn.to/3nf4l29
Wheels: amzn.to/30zkFRI
HC-05 Bluetooth Module: amzn.to/36w2DU5
18650 Battery Holder: amzn.to/34nOVA6
18650 Battery: amzn.to/36EeUWu
L293D Motor Driver: amzn.to/3ng7Xks
Switch: amzn.to/3ivaUdw
Jumper Wires: amzn.to/3izMFe2
Samsung 18650 Battery: amzn.to/2JaAKb0
10mm RED LED: amzn.to/2Kxx8jx
8MM White LED: amzn.to/3fAjuYk
180R Resistor: amzn.to/2V3TbAt
Wire for motor connection: amzn.to/2HEg4aF
Double-Sided Tape: amzn.to/365cAaz
Banggood Links:
Arduino UNO R3: bit.ly/2FZY6dT
TT Gear Motor: bit.ly/2Mlb35E
Wheels: bit.ly/2U10QPM
HC-05 Bluetooth Module: bit.ly/2ukQvod
18650 Battery Holder: bit.ly/2MkPYrW
18650 Battery: bit.ly/3eBNH7N
L298N Motor Driver: bit.ly/3gB8Ws6
L293D Motor Driver: bit.ly/2CHPqdT
Switch: bit.ly/3ds4Xfy
Jumper Wires: bit.ly/2MjLy4t
Thank you so much for watching the video. Please hit the like button it really motivates me a lot. And also don’t forget to subscribe for more amazing Arduino related content.
Do you have any queries about the Arduino Project? Then do let me know about that in the comment section.
Music Used in the video:
chill. by sakura Hz / sakurahertz
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/chill-sakuraHz
Music promoted by Audio Library • Chill - sakura Hz (No ...
Agdal - Soyb / soybmusic
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/agdal-soyb
Music promoted by Audio Library • Agdal - Soyb (No Copyr...
Lounge Generation · Randy Sharp
Link: artlist.io/song/38139/lounge-...
She No Dull Beat
Timpani Beat
UA-cam Audio Library
#DIYProject #ArduinoProject #BluetoothCar #L293D - Навчання та стиль
Here is the Schematics and Code: circuitbest.com/c/dHk0t
Enjoy :)
This link doesn’t work
Plz give me code
Give me code
Code is not downloading.
Please send blutooth app link
You deserve a lot of appreciation for this great work.
Looking forward for more these type of videos
Worked like a charm. Each and every steps are clear. Code is fantastic. Even a beginner can understand the code easily.
Looking forward for seeing more videos from you.
Love from India ❤️
Can you send the mobile application file in (aia) format to add other specifications ??
@@mohammedasfour684 code link is not working.
where i find the code.
ua-cam.com/video/jZccpvVWn0M/v-deo.html
How much rpm motor
ua-cam.com/video/yu3at4F9CFs/v-deo.html
its amazing how you made such a simple project into a good quality video, i liek the lighting
Perfect and the details you provide in the link in the description is extraordinary detailed and clear with comprehensive explanation, great effort and very well done, many thanks
détaillé, clair, complet : superbe. Merci !
ua-cam.com/video/jZccpvVWn0M/v-deo.html
Give it minimum 12 volt, and upload code well, and take care of connecting rx and tx with bt module carefully it will work definitely
Thanku sir just make in 1 Hour by watching this tutorial very helpful
Working 💪
Unbelievable........very good effort 👍
Que aplicación se usó para exportar el código al arduino?👀
I'm looking for this video for a long time thx🚀❤🚀
You are welcome 🤠
Good efforts i appreciate your work
thanks a lot man , it works , keep it up , great job
Don't forget to subscribe 😉
Bro plz help.me yar...what is at 9.24 ?? Which software..is this ??
@@MakeDIY9 sir i have spent 3000+ in this project but i didnt understand what to do at 9.24 ??? What is that ?? Which software ?? Plz help me sir..
@@rakeshanjani3481 bro its arduino , you have to copy the code he has given and upload it. You can download it like shown in this video:
ua-cam.com/video/TbHsOgtCMDc/v-deo.html
bro whats the cost
Keep it up bro!
Thank you 😊
Amazing work 👏
Nice Mind-blowing work ❤
is this work properly?
Great video, can you please give a link for the led holder for the car please
Ive made this project and its amazing, soon i will 3d print the whole car, even wheels and it will be even better
Niceee 😄😄
Hi, can I ask what the whole printed car looks like? I would need some design for the car body to cover the components, Arduino, etc..
@@Magic-wz1zs ive done it in fusion 360 hobby use
@@judlex7300 hi
@@geotalk2023 ??? Hi i guess?
You provide me perfect guide about project 🙂
So hardwork you need appreciation
Do you have any Proteus Circuit Simulation for reference? And very clean information love it ❤️
I haven't simulated it but i done it practically....🙂
ua-cam.com/video/jZccpvVWn0M/v-deo.html
@@MakeDIY9 I have made this project just now but don't know why it's speed is too slow but after I remove its tyre even though it's motor speed is too slow....what can I do si
@@MakeDIY9 I have made this project just now but don't know why it's speed is too slow but after I remove its tyre even though it's motor speed is too slow....what can I do sir
@@MakeDIY9uygulamnın linki lütfen 😢
Can you make 2 wheel balancing robot with this shield?
That's great,,,, highly appreciateable,, having great mind bro 👏👍
Dream project 🤩
Awesome project bro!! But one question, is it possible to use a 9v battery instead??
It may work but car will run for few minutes only
@@MakeDIY9 Ok thanks for replying. So will it last longer if I take off those LED's ??
No bro those leds only takes 20mA of current it is barely noticeable. But the motors that are the culprit for the main discharge. But if you want you can remove the leds and also make the car 😃
@@MakeDIY9 Ok thank you so much bro!! I loved your replies and projects👍👍. Btw even I make Arduino & electronic projects so if you want to you can check it you're most welcome to my channel.
I loved your project, keep it up amazing work🤘👌👍(I have subbed to your channel)
you can use two 9v battrey
What app you use to design wiring please?
Arduino IDE
Very useful informative video 👏🏻👏🏻👏🏻👏🏻
Excellent work 👍
please provide complete code, very useful information.
i do not no
#include
#include
#include
Servo towerprosg5010;
int pos = 10;
int HM10_RX_PIN = 50;
int LED_PIN = 48;
int HM10_TX_PIN = 51;
AF_DCMotor motor1(1);
AF_DCMotor motor2(2);
AF_DCMotor motor3(3);
AF_DCMotor motor4(4);
SoftwareSerial bluetoothSerial(HM10_RX_PIN, HM10_TX_PIN);
void setup() {
bluetoothSerial.begin(9600);
pinMode(LED_PIN, OUTPUT);
towerprosg5010.attach(9);
}
void loop() {
if (bluetoothSerial.available()) {
char command = bluetoothSerial.read();
if (command == '1') {
digitalWrite(LED_PIN, HIGH); // Turn on the LED
} else if (command == '0') {
digitalWrite(LED_PIN, LOW); // Turn off the LED
} else {
// Stop the motors for any other command (including no command)
stopMotors();
// Execute specific commands if needed
if (command == 'F') {
forward();
} else if (command == 'B') {
backward();
} else if (command == 'R') {
right();
} else if (command == 'L') {
left();
} else if (command == '2') {
towerprosg5010.write(0);
delay(100);
} else if (command == '3') {
towerprosg5010.write(180);
delay(100);
}
}
}
}
// Function to move the car forward
void forward() {
motor1.setSpeed(255);
motor1.run(FORWARD);
motor2.setSpeed(255);
motor2.run(FORWARD);
motor3.setSpeed(255);
motor3.run(FORWARD);
motor4.setSpeed(255);
motor4.run(FORWARD);
}
// Function to move the car backward
void backward() {
motor1.setSpeed(255);
motor1.run(BACKWARD);
motor2.setSpeed(255);
motor2.run(BACKWARD);
motor3.setSpeed(255);
motor3.run(BACKWARD);
motor4.setSpeed(255);
motor4.run(BACKWARD);
}
// Function to turn the car right
void right() {
motor1.setSpeed(255);
motor1.run(BACKWARD);
motor2.setSpeed(255);
motor2.run(BACKWARD);
motor3.setSpeed(255);
motor3.run(FORWARD);
motor4.setSpeed(255);
motor4.run(FORWARD);
}
// Function to turn the car left
void left() {
motor1.setSpeed(255);
motor1.run(FORWARD);
motor2.setSpeed(255);
motor2.run(FORWARD);
motor3.setSpeed(255);
motor3.run(BACKWARD);
motor4.setSpeed(255);
motor4.run(BACKWARD);
}
// Function to stop the motors
void stopMotors() {
motor1.setSpeed(0);
motor1.run(RELEASE);
motor2.setSpeed(0);
motor2.run(RELEASE);
motor3.setSpeed(0);
motor3.run(RELEASE);
motor4.setSpeed(0);
motor4.run(RELEASE);
}
thats a old code I have for a rc car I made a few years ago you will have to change the rx and tx pins in the code I have 1 LED added in there and a servo (You can just leave them in the code) but you can change the pin of the LED to match a pin on your board and add more if you have room hope it works for you also remember to put the rx of the bluetooth module to the tx of your board and the tx to the rx of your board if you are using uno it's pin 0 and 1
Hey ,nice video i have joined all the circuits ,and entered the codes too but bluetooth isn't showing up on my phone ,could you help me with that ,thanks in advance, btw great work👍
i like his soldering iron tip and soldering skills
Please make a gesture controlled robot with 433 Mhz module
Ok
Hi, I tried your code and car assembly and worked like a charm! However is there a way to vary the car speed?
Change the code and if it doesnt work buy better motors
Change the speed values it will do the work
@@MakeDIY9 Yes, but if you want really good speed you would need brushless motors and better car build
How much rpm is the motor?
bro whats the cost
This was the best video that i saw , and hell i will subscribe to this channel only for the sake of that
Awesome project💕💕💕
How much volts battery need to be chosen?
Max 12v is great
@@MakeDIY9 and what about amps sir. I am allways get confused how to select volt and amprs for any electronic applications. Please clarify me sir.
2 amps are ok
Bro I connected with the app and paired it too and it showed gree colour also but it's not moving pls help
Did you get any solution?
Bhai yhi hota hai... Mere sath bhi yhi ho rha hau jina easy lgta hau nhi... Sb krne ke baad command nhi maan rha
Did you Uploaded the code
u will have to attach a higher volt battery
@@khushboogosalia9675 is it working for you?
Precisely done✔ 👍 👌
Outstanding 😊
How did you connect the switch to the battery holder?
Good job 👏🏻👏🏻👏🏻
marvellous 😊
So interesting bro👍
Amazing 😊
Fabulous 😍
Amazing 😍
What app did u use and thank u for the amazing ideas and steps on how to make it but I cannot find what app it is
If I use HM-10 Bluetooth module is this codes work? Or I need to alter some codes?
Do you have self Balancing robot project using L293d motor shield?
Nice Work bro Keep up
Brilliant❤
This Car Is Really Amazing 💯💯💯💯💯
Its workkkk!!! I can`t believe that arduino is so cool!
thank you so much for this video
our project worked succsessfully
Excellent effort
The lights are a nice touch. I also appreciate the zip ties for a nice clean look. 👌
Perfect work
Really work hard tells how to made a simple project
love how ardino's work
Keep it up!
Thank you bro❤️😊
You are welcome ☺️
Wow you make an awesome project but it's costly can you please tell from where to find all components at a low cost, please
Nice one ❤
Nice work 👍👍👍
hello bhai , wo tune wire ko join karne ke liye wo wires ko melt kiya wo kaise kar sakte hai
Outstanding 👍
I am building a car like this
But if I have to set it up on the computer for what it is to set up, it will be very useful to show me a little bit
Amazing work
This DIY is fab
fast technical support 💪💪
Impressive Bluetooth connecting 🚗
Joli travail mon ami!!
Good work nicely done
Working bro thanks for the contribution
Great effort
Love these cars
Fantastic 😊
Very useful for my science club
Beautiful
Can we use 1ohm resistor?
awesome and like the way you go
is it safe to build all this on that wood plank?
Also idk how this stuff works, but i assume gluing those motors into the wood is safe and won’t cause overheating or something.
Dude, the electric just come out from DC Battery,, Nicola Tesla was guaranty that all of them safe.
Excellent ❤❤❤
Great work boss you are awesome
Work like a charm
great work! I did it and it works perfect!
Which software you used for coding
Hey bro
Which software you used for coding
whats the cost bro
Ardino are always so cool
Bro kiya ham isme 11.7 v ki battery de sakte hai kya kiyo ki mai 12v ki motor use kar raha hu please bro bata dena
Noicee 👌🏼
Magnificent
Ultimate bro super and simple
Wow Amazing car😊
Wao amazing
Wonderful 👍👍👍👍
Amazing 🎉
Very nice good work 👏👏👍👏
is this work properly?
please tell
Excelente.
Good job 👏
Awesome work
Perfect
Wow look amazing