How to Replace LED Strips in LG LED TV - 55LF 55LB NC55 - Fixing Bad LED Backlights

Поділитися
Вставка
  • Опубліковано 23 тра 2017
  • LED Strip Backlighting Replacement Video
    CLICK HERE to Purchase: www.shopjimmy.com/catalogsearc...
    LG TV Models:
    55LF6000-UB AUSCLOR
    55LF6000-UB BUSCLOR
    55LF6090-UB
    55LF6000-UB BUSYLJR
    55LB5900-UV BUSWLJR
    55LF6000-UB BUSYLJR
    55LB5900-UV BUSDLJR
    55LB5900-UV BUSCLJR
    55LF6000-UB BUSCLJR
    55LF6100-UA
    55LY340C-UA BUSDLJR
    Try all repairs and troubleshooting at your own risk.
    In this video we will show how to replace the LED strips in certain LG TVs.
    This is a generic tutorial, and if your TV model is listed in the video description, the general process shown in this video should apply to your TV, even if there are some small differences.
    When replacing LED strips, you will have to remove the panel.
    Removing the panel can be very difficult. If your TV panel is damaged during the replacement process, you will have to get a replacement TV.
    Start by removing the screws and the back cover off the TV.
    Disconnect the cables to the speakers and set the speakers aside.
    Disconnect the cables to the t-con board and to the scan drive boards. Remove the screws and the plastic cover over the t-con.
    Remove the screws on the metal covers that are over the scan drive boards.
    Remove the screws for the TV bezel.
    Adjust the tabs and remove the metal covers.
    Release the scan drive boards.
    When releasing the scan drive boards, disconnect the ribbon cables on the scan drive board. These cables are the ones that connect from the scan drive board to the t-con board.
    Remove the remaining bezel screws.
    Flip the TV over and remove the bezel.
    Flip up the scan drive boards and tape them to the TV panel.
    Release the tabs and tape on the side of the panel to release it from the chassis.
    Use suction cups or something similar to lift and remove the panel from the chassis. We do have the suction cups available for purchase at ShopJimmy.com.
    Release the tabs on the filter frame and remove it from the chassis.
    Tape the corners of the light filters before removing them, to keep them in order and together.
    Lift and remove the light filters.
    Pinch the reflector clips to remove them from the panel.
    Remove the clips on the front side of the chassis.
    You will need to push them to the side and then lift to remove them.
    Remove the reflector sheet.
    Take pictures of the original LED strips to help when reinstalling the replacements.
    You will want pictures of the strips connected to the cables in the order that they go in.
    Disconnect the cables from the LED strips.
    Using a five in one tool, or something similar, remove the LED strips.
    It may help to use a five in one tool and something to push the tool from the back.
    Install the replacement LED strips. They may be sticky on one side, but we will use some double sided tape, just to be sure they adhere to the chassis.
    It may happen that an LED lens gets knocked off when installing the LED strips. If this happens, and you need to use that strip, you can use super glue or hot glue to put the lens back in place.
    Install the replacement LED strips and reconnect them to the cables. Be sure they are properly aligned.
    Install the reflector and begin installing the clips.
    Reinstall the light filters and remove the tape.
    Reinstall the filter frame.
    Reinstall the panel.
    Reconnect the tabs and tape on the sides of the panel.
    Release the scan drive boards.
    Reinstall the bezel.
    Align the scan drive boards and the tabs and reinstall the metal covers.
    Install the screws for the metal covers and bezel.
    Reinstall the plastic t-con cover and reconnect the ribbon cable to the main board.
    Reconnect the speakers.
    Reinstall the back cover.
    TV Repair Made Easy™
    © 2017 ShopJimmy.com, LLC.
  • Навчання та стиль

КОМЕНТАРІ • 294

  • @willardarmbruster8111
    @willardarmbruster8111 4 роки тому +391

    I'm so glad I watched this. Tomorrow I'm going to buy a new TV.

    • @Sertao2013
      @Sertao2013 4 роки тому +8

      Can I have your old one ? I have a few lines in my screen and I need a new screen ?

    • @MrSegAsh
      @MrSegAsh 4 роки тому +48

      Yep me too. Fuck this shit.

    • @thuggy67
      @thuggy67 4 роки тому +3

      Lol

    • @adiohead
      @adiohead 4 роки тому +2

      🤣

    • @tankgirl9324
      @tankgirl9324 4 роки тому +4

      LOL

  • @gabbyprod
    @gabbyprod 2 роки тому +35

    Great tutorial! Fixed my LG $1,500 for $24 in an hour.
    1 down, 2 to go.
    Thank you!

  • @chk1chk2
    @chk1chk2 3 роки тому +11

    Just repaired my 61” LG following your video and saved a $1000 TV for $60 for LED strips off of eBay! Thanks for the video!!

  • @Saagemusic
    @Saagemusic 19 днів тому

    This was incredibly thorough and extremely helpful. I am very thankful for finding this video. Thank you for showing us how to fix our tvs ourselves instead of overpaying and relying on others.

  • @daviddaniels4075
    @daviddaniels4075 5 років тому +4

    My TV started to flicker on and off the other morning. After dealing with LG Support, I got on UA-cam to see if I could figure out my problem. I came upon this video and decided I would give it a shot. When I received my new LEDs, I noticed the + and - markings on the new ones were different than the markings on mine. I contacted Shop Jimmy to inquire about the difference as I did not want to fry my TV. Shop Jimmy assured me the strips were correct and that the plugs would need a little extra pressure to install them on to the new strips. I proceeded with the install and my TV now works like a brand new one. Thanks Shop Jimmy for your product, video, and your professional support team. FYI my TV was a LG model 60LB6500-UP.

  • @gainmaster1
    @gainmaster1 3 роки тому +7

    As a person who has already done this you don't need to do half the stuff this guy is doing. 1. No need to buy suction cups, place screen face down on a towel let it rest there instead of trying to lift screen. 2. No need to hammer and chisel the strips off they just pull off if you do it with care keeping your hand close to where you pull. 3. Unless all of your strips / LED's are burnt out i wouldn't be replacing the entire strip(s). They are quite expensive to buy and you are not guaranteed they are new, and if second hand you don't know how many hours are on them. The cheapest way is to buy individual LED's from Ebay or Amazon costing cents and replacing them. They are easy enough to replace with a soldering iron. I have done this on exact LG in video and replaced 8 burnt LED's, Job done.

    • @memphistiger4647
      @memphistiger4647 2 роки тому

      Just curious once you have the LEDs in plain view how do visually know which ones are bad? This guy replaced all of them in the video. Should I just assume they're all bad?

    • @gainmaster1
      @gainmaster1 2 роки тому

      @@memphistiger4647 a lot of the time the LED will be discolored, not usual yellow. And the ones that are burnt out will have a black spot or mark somewhere on diode. Best way is to test with a LED tester. Cheap on EBay or Amazon then replace individual LED’s which are also cheap. If you try to buy complete strip then it will end up being very expensive especially if only one or 2 LED’s burnt out on strip. All depends how long you want fix to last. Might have same issue with other LED’s over time but to get it working that is the way to go. Having brightness of backlight up to 100% causes this issue especially if TV isn’t that old.

    • @HKS2000
      @HKS2000 2 роки тому

      Do you know the order of the filter screen?

  • @OvervoltedMinds
    @OvervoltedMinds Рік тому +3

    This was super helpful! Just finished repairing a 49” one. It wasn’t exactly like the one in the video, but pretty much there. Took me a couple of hours but not too complicated. Patience and care is all you need.

  • @plugtwo9278
    @plugtwo9278 5 років тому +3

    Thank you ShopJimmy! I just reconnected my LG47LB5800 and it works again! [40+ SBF] I ordered the LED strips and double sided tape from ShopJimmy. The suction cups and 5-in-1 tool were out of stock, got those from Amazon.
    One additional suggestions take a photo of how the wires are connected as well as the proper order for the strips. Also use a lightweight tape to keep the filters together.

  • @randomstring200
    @randomstring200 3 роки тому

    Thank you Shop Jimmy; tutorial very well done, scripted and edited; for the record, it is applicable also to the 60" version of the TV, the 60LB6500-TA.AAUWLJD, which is sold in Australia; identical clips system holding the white sheet and identical overall layout; keep doing these videos, they are very much welcomed and appreciated.
    Note: I have tested the LED strips before replacement, and, in my case, (of the 6 strips) 3 were shorted (!!!) and the remaining three had one led not coming on, and the others were relatively faint. I am now going to buy the strips.

  • @alexandreasanzone5963
    @alexandreasanzone5963 6 років тому +34

    This video is amazing, I am a young female and I fixed my own tv thanks. I am so proud of myself

    • @johnkanuchok
      @johnkanuchok 6 років тому +1

      Congratulations. I'm thrilled when people try and succeed! Good job!

  • @danielvaldez9826
    @danielvaldez9826 3 роки тому +1

    I ordered from this website and fixed my tv just like in this video. Thank you for the video, I really appreciate being able to fix my stuff and not have to buy a replacement. Thank you Thank you!!!

  • @scottbenton1314
    @scottbenton1314 5 років тому +4

    I was given a 55" LG with the picture flashing on and off. Dismantled it per your video and found 36 of 55 of the backlight LEDs burned out. Replaced all the strips with new ones from Shop Jimmy and now I have an "almost free" 55" TV. Set the backlight to 73% to hopefully prevent future burnouts! Thanks for your concise videos and great parts selection!

    • @matthewafaridan383
      @matthewafaridan383 4 роки тому

      That's what I wanted to know, I got a free 50 inch, the light strips flicker, pulled apart, found a few blown leds, I'm guessing by your comment that replacing these will fix it? Or at least it did yours?

  • @jasongarcia6678
    @jasongarcia6678 11 місяців тому +2

    Thanks! Just fixed my old LG. It took about two hours for me, but worth it.

  • @dalehawke7621
    @dalehawke7621 2 роки тому +2

    So glad I found this video,as I am attempting to replace the LEDs on my LG 55lb650v tv this Friday , excited to try doing this myself, but also nervous,but if I'm able to do it myself,then I'll save myself a lot of money in the future if my TV's go wrong .

  • @alialshabeeb8401
    @alialshabeeb8401 5 років тому +14

    Today I finally fixed my tv according to this video and I become very happy. I just want to say thank you very much from bottom of my heart.

  • @sprayedi
    @sprayedi 3 місяці тому

    I just fixed my 55" LG with this tutorial, just cost me 20 euros! Thank you!! Took a few hours, because did not want to break anything 😅 but it was well worth it!

  • @mrgallardo7069
    @mrgallardo7069 4 роки тому +6

    Just installed the new leds on the same TV your doing and wow was it pain in the ASS . But thankfully it works now and hopefully it does not break again. Thanks for the video .

  • @KennySpark8574
    @KennySpark8574 4 роки тому +2

    thanks, i followed your video and got my 47" lg tv working again! many thanks god bless

  • @PenguinQueen5000
    @PenguinQueen5000 10 місяців тому +1

    I was about to buy a new tv before I found this video. Thank you for sharing this. It was super helpful. Really easy to follow and note my tv is working like new and the only cost was $45 on amazon for the parts.

  • @MrMunni
    @MrMunni 3 роки тому +1

    I used this tutorial and fixed my TV. Super happy.

  • @robbiewilson157
    @robbiewilson157 Рік тому +4

    Great video. I had 2 tables set up with blankets though and flipped the lcd face down on the blanket after i got all the circuit boards loose and lifted the backlight assembly off since i didnt have sx cups. AND it seemed likely for me to break something lifting it and flopping it around. replaced the leds on table 2 and flipped it back.

  • @darrendexter6125
    @darrendexter6125 3 роки тому

    Thank you so much!, This helped me a lot with accessing and taking off the LCD and light filter layers. Saved me a lot of time and possibly breaking something.

  • @danst9655
    @danst9655 Рік тому

    Your video helped me fix my 43um LG TV. I did break a few brackets in the bezel while prying the back cover off but it all get together firmly enough.
    Many thanks!

  • @Mangotrond
    @Mangotrond Рік тому

    Thanks, dude.
    Just did this on my 60UJ634V.
    Mostly the same procedure.
    The picture got darker and darker and more blue on mine. It started with it showing up blue when I took photos of the screen with my phone.
    After replacing the LEDs, its brighter and whiter than I could even remember.😁

  • @jasonglick3473
    @jasonglick3473 3 місяці тому

    Amazing! I bought an LG 65JU6300 with blue screen for $75. This tutorial helped so much, it's like new. Thank you.

  • @daleyhenry2256
    @daleyhenry2256 4 роки тому

    Followed this video today and my lg tv project was a success 🙌 thank you

  • @philipjon8151
    @philipjon8151 2 роки тому +1

    With your parts and video and 3 hours lguh6100 fixed Thanks Jimmy , The last TV I fixed required a 2N3055 transistor a long time ago lol

  • @christinerussell6252
    @christinerussell6252 3 роки тому

    This was tremendously helpful! Thank you!

  • @anthonyspencer3808
    @anthonyspencer3808 3 роки тому

    Thanks!!!!! i followed the video and now have new life with my tv. works great.

  • @aviery89
    @aviery89 5 років тому +2

    You’re the best! Worked like a charm

  • @burrencrawler
    @burrencrawler 4 роки тому +8

    What an awesome straight to the point no bull video, did it on our 47" LGTV.... Thanks, saved us some money there, took over an hour, and great fun too, thanks!

  • @stephenperez3134
    @stephenperez3134 4 роки тому +3

    This video was so helpful. I have this exact same LG TV and was able to follow disassembly and thank-you for including the reassembly process. Another TV saved from the landfill. Thank-you.

    • @oldschool2546
      @oldschool2546 2 роки тому

      It was the same for me. Was able to repair the TV. Thank you.

  • @bign00bs
    @bign00bs 5 років тому +10

    I just repaired my LG 55" by using this site and this video. Thanks!
    Symptoms - noticed dark spot fluctuating in intensity in top right of tv. This happened for a few days until the tv started to turn off and on in a continuous loop. I decided to replace all of the LED's because this is what I noticed FIRST before the power cycling and because this is a known issue with this LG model, according to various internet search results.
    I watched the entire video first. Then, I followed the video step by step, pausing before proceeding to the next step.
    The wire connectors/jumpers did not have the same fit as on the original LED strips. I used a standard screwdriver to GENTLY but forcibly push the connector into place on the new led strips.
    Suggestions: Watch your fingers when removing the back of the TV, mine has extremely SHARP edges in places and will slice into your fingers. Get the suction cups and the tape. Make sure you have PLENTY of room. Use a blanket for protecting the screen/table (not a thick quilt). If you are able to work on a table, this will save your back and your knees. Wash your hands before touching the filters. Get a few small containers to hold the screws and fasteners. The filter bezel clips were delicate on my tv. I broke 1 because I hulked out, be careful with these. I replaced the strips 1 entire row at a time. I think all but 3 lenses popped off the old strips while removing them so I don't recommend doing this with small children or animals around due to possible choke hazard, make sure you account for each one if you do have children or pets. The old lenses look like they could be used for some artsy fartsy craft project so give them to your grandma or some old person ;)

    • @wizardglick9609
      @wizardglick9609 5 років тому

      How long did it take for the entire job?

    • @NewUser-ni5tx
      @NewUser-ni5tx 4 роки тому

      Wizard Glick took about 5 mins brcause i just bought a new tv lpl

  • @robertwalker5564
    @robertwalker5564 2 роки тому

    Your rock man, such a good video. Got a flickering tv from a friend and fixed it with ease!

  • @ensidfkgnur
    @ensidfkgnur 6 років тому +1

    Got my ShopJimmy replacement strips in for my LG 55LB5550, I simply mimicked the person in the video and everything went smoothly. The TV has only been running for an hour so no telling how long they'll last but it looks great so far!
    Glad to see they were not OEM or pulls, they're completely different, which is great because so many people have had problems with the OEM I think they're fundamentally flawed. The OEM wires and connectors won't work on these so be sure to use the included connectors.
    Awesome video, awesome replacement strips so far!

  • @luisjoseacevedo3353
    @luisjoseacevedo3353 7 місяців тому

    Thank you so much for this video! It saved my LG 82”! It wasn’t easy but it worth it! I got the pieces from your website!🎉

  • @Patch1stripeTVParts
    @Patch1stripeTVParts 6 років тому +2

    Great video!!! Thank you.

  • @pitada72
    @pitada72 Рік тому

    Thank you very much. Very easy to do. Thanks to your video I was able to change the LEDs on my TV. 👌

  • @iainbird9898
    @iainbird9898 4 роки тому

    Thank you. I would have not attempted this unless I was in virus social distancing spare time. I would normally have purchased a new TV.
    Thanks to your help I now have a repaired 47LB585V TV with a stunningly good picture (it was given to me as broken).
    It would have helped if you'd mentioned that it's easier to remove the three pointed standoffs in the middle, if you temporarily remove the PSU board and motherboard. The are much easier to remove if you can access both sides of the chassis plate.

  • @jonasgutenberg8387
    @jonasgutenberg8387 2 роки тому +1

    While my TV was different, the procedure was almost the same. For a minimal price was able to fix it myself, thanks for your detailed and explanation

  • @4thesakeofitname
    @4thesakeofitname 4 роки тому +19

    I have applied every step here, with great care (as much as I could) I have taken the risk of removing the LCD panel which is the most expnsive and fragile part in the assembly. It's not very easy to remove every connector as well, especially the panel driver connector is very sensitive too. There are so many screws and all sorts of clips and one must be very careful to remove them without damagnig the TV. I have used a smaller set of vacuums to hold the LCD but they did the job (still paying great attention while holding the LCD panel)... Hint: this LG model of mine, claims that its LCD is immune to mechanical crashes, so I was hoping that bending during panel removal won't cause a problem... So many levels, very tiring, it took about 4 hours for me. (one hour for just one defective screw!) At the end of the day, I have managed to replace one line of leds which was defective... Thank you sir for this extremely helpful guide. ..
    *UPDATE:* four months ago I have replaced one row of 2 LED bars (A and B type), and commented the result. Now, last month another LED strip from the remaining bars also burnt... :-(. This was expected, but not so soon, the time was somewhat shortened due to the Corona virus stay-home full time TV netflix watching... :-) So, this time I decided to replace the whole set of 10 bars. Last week I bought 5 rows (10 bars) of new LEDs. Reopened the TV and replaced all the bars. One thing I observed was that the defective bar was connected to the renewed bar. Note that among 5 rows, upper two were connected in series and the lower three were connected separately in series. So the new and old bar connection in the upper part failed before the lower three older bars. This supports the fact that renewing just one bar (or one led) among older ones, impose more strain on the remaning bars and kill them faster than otherwise. So it's better to replace them all together unless something else was necesary. It was extremely tiring again. The internal frame that holds white polarizor screening really was a headache. Also moving the LCD panel was a thrill too. Indeed one of the vacuum cups broke during the panel removal but I was lucky as the drop height was less than half a foot. But then I had to find another (safer) approach to remove the LCD screen, not relying on suction cups. Slightly pull the LCD panel aside without scratching and bending it. Note that this model of LG TV claims to have a scratch and hit immune LCD coating. It was demonstrated to me when I decided to buy it. The seller hit the screen with his palm and said that this IPS panel was strong enough to survive children filled house accidents! Anyway. At the end of the day I managed it. But there was a disaster ! In the first trial I have forgotten to connect one cable on the last LED bar! The TV didn't work OMG !!! I almost gone crazy!! but then I re-opened the TV and found that I forgot to connect the LED bar connector at the lowest bar !!! OMG I was happy but very tired! You know. I do not suggest this LG TV. It's overall a good TV but first its LED lighting strategy is wrong which burns then at 4 to 5 years! Furthermore, the white-screen is not fully uniform in brightness and there are ghost shadows on the screen when a white background shows up, especially when it moves fast enough the gost shadow pattern becomes painly visible. I do not suggest this TV because of this. But the functionality of the TV is quite good. It connects very well with computers, ADSL box and other devices. Its built in satellite decoder is also working fine, despite being slow in channel seek...

    • @alextomlinson
      @alextomlinson 2 роки тому

      @Dann NY me too

    • @mullioncove1
      @mullioncove1 2 роки тому

      Please do not use the OM expression there is no need God Bless

    • @HKS2000
      @HKS2000 2 роки тому

      Do you know the order of the light filter?

  • @ach-eww1866
    @ach-eww1866 2 роки тому +1

    The first TV I fixed was my 65 inch 4k Smart TV I got for free from someone who said only the bottom strip of lights worked, me being new to this didn't care and wanted to try it out, got new LED strips, and 11 hours and taking it apart 3 times later, I got it, don't know how I didn't break it. Forgot the piece of cardboard inside that I used to help get the screen out, so had to take it apart the second time, then had to take it apart a third time because there was a small piece of tape on one of the ribbon cables to the t-con board and so half the screen was flickering and discolored until I took the piece of tape off allowing the first few pins to reconnect, lol. It was a nightmare, but it was fun

  • @sorinsleam3467
    @sorinsleam3467 4 роки тому +15

    thank you so much, I managed to change the LED's myself. Thank you :)

  • @sandman7793
    @sandman7793 Рік тому

    Awesome video. In the process of doing a 82 inch. It's setup the same way. The panel is hugh and heavy though.

  • @condreacata
    @condreacata 3 роки тому

    Thank you! It worked for me!

  • @resilient4637
    @resilient4637 Рік тому

    Thanks for the information at least it's a project when I get the weekend

  • @gabbyprod
    @gabbyprod 2 роки тому +4

    Great video.
    I'm fairly technical, but would never have just dug in and tried to replace the LEDs without this video.
    I got 3 of these TVs and they all have the purple screen, so I'm hoping this does the trick!

    • @metrork1
      @metrork1 2 роки тому +1

      LED Tester 0-300V Output Multipurpose LED Lamp LED TV Backlight Tester Tool

    • @FraggedByMe
      @FraggedByMe 2 роки тому

      did it fixxed it? my top right corner is blueish, i think i have the same issue

    • @nixonrodriguez4865
      @nixonrodriguez4865 Рік тому

      ​@@metrork1 hello i i put in back ligth is on but now i can change the channel why gelp😢😢😢

    • @nixonrodriguez4865
      @nixonrodriguez4865 Рік тому

      ​@@metrork1hellll0

  • @crispylimbs
    @crispylimbs 2 роки тому +2

    Thanks for uploading this I’m going to try and replace the LED back lights on my LGTV tomorrow. The only thing I would say is, wouldn’t it make sense to unclip those pins before you flip the TV over so that you don’t have to flip it back again once the screen is loose…? Thanks 😊

  • @Mill-on-da-track
    @Mill-on-da-track 2 роки тому

    I'm halfway finished changing mine I just want to say thank you for this tutorial 🙏🏼 I also ordered my led strips from you guys as well

    • @HKS2000
      @HKS2000 2 роки тому

      Do you know the order of the light filter by any chance?

    • @Mill-on-da-track
      @Mill-on-da-track 2 роки тому

      @@HKS2000 no I taped the cornes of mine with painters tape so I wouldn't get them out of order and just put them all back in at the same time

    • @HKS2000
      @HKS2000 2 роки тому

      @@Mill-on-da-track technically they are still in order except for the thickest one thick on on bottom or top

  • @islamsadek7046
    @islamsadek7046 2 роки тому

    You saved me
    Thanks so much for the video

  • @eryutu
    @eryutu 3 місяці тому

    Good job!! Thanks for sharing. New subscriber

  • @rubeschm
    @rubeschm Рік тому +2

    Worked like a charm in repairing a free TV I found on Craigslist list. Not half as intimidating as it originally seemed.
    Before we attached the new LED strips we put the reflector sheet back down to mark where they should be for the new ones. Might be a worthwhile idea

  • @eliadeteodorovici404
    @eliadeteodorovici404 4 роки тому +3

    Any idea how the platic clips are named? I`m trying to find them over the internet but didn`t had any luck. I broke about 3 of them when trying to remove.

  • @feesakkers
    @feesakkers 2 роки тому

    Thank you so much, it took me a while but it solved my problem. So I do have picture again, but one small vertical line is grey. Could it be the LED strips or did I accidently damaged something? Either way, still thanks a bunch!

  • @karimchedid
    @karimchedid Рік тому

    Thanks a lot very helpful fixed for 20$ 🙏🏻

  • @manickvel5004
    @manickvel5004 Рік тому +1

    Still running 22 years old CRT without this kind of major repairs

  • @codycarlson6557
    @codycarlson6557 4 роки тому +3

    Just did this was super easy if you just follow directions. I didn’t have suction cups either I just carefully lifted the screen out making sure not to bend it. What do you have to lose? If you do lose your tv is apart and you can sell the motherboard and all the components that still work on eBay and make yourself some cash!!

  • @johnlee5937
    @johnlee5937 2 роки тому +3

    No wonder there are no TV repair shops.
    The labor cost for this probably makes this impractical.

  • @FunkyFish13
    @FunkyFish13 Рік тому

    Thank you for video !

  • @ckat609
    @ckat609 11 місяців тому

    You, sir, are a godsend! Does anyone know how to clean the reflectors? I smudged one of them 😢

  • @jaj040
    @jaj040 5 років тому +1

    Just fixed my 55" LG!

  • @aaaaaa-qc9ot
    @aaaaaa-qc9ot 5 місяців тому

    Some white pieces you were removing at 7:32 broke. Do you know whether they are sold? If so, what is their technical name? By the way, thanks for the video: it is one of the best!

  • @imagerose
    @imagerose 5 місяців тому

    Great job, kudos! Can you please indicate the exact name/type of the red tape you used (at min 4:06 etc.)

  • @jericho7899
    @jericho7899 6 років тому

    Is this the 55lb5900 model in this video?

  • @shadrackongeri9559
    @shadrackongeri9559 7 місяців тому

    Thank you for this video, il now have to buy a new set.

  • @harolddennison122
    @harolddennison122 3 роки тому

    Fixed my TV thanks to this video. If I ever meet you... Beers on me ;)

  • @theattorney6072
    @theattorney6072 Рік тому

    Hello, thx, do you have an Idea how to change and where to find the LEDs for the LG 55LA970V (olso called 55LA9700) ?

  • @trevorschooler700
    @trevorschooler700 2 роки тому

    Thanks u for your information

  • @bro.allenm1974
    @bro.allenm1974 Рік тому

    Thanks for this video. I have a question, possible issue. Does it matter far as the lettering is concerned? I took photos for the connection concern not the order of letter.

  • @user-me3kj1mf5l
    @user-me3kj1mf5l Рік тому

    Is the blue or white wire the negative feed? My TV has 3 wires that run to the connections. There is a black & blue to 1connection, blue & white connections to 4 other connection points and 2 connections with a small blue wire loop that connects to the led strips.

  • @Gunner11763
    @Gunner11763 4 роки тому

    I've an LG 4k tv and there is one or two spot showing up that have like a purple colour to it.. Is that the blacklight failing and if so would all the leds need fixing.. Thanks in advance

  • @32Manz
    @32Manz 5 років тому

    We followed all the steps to replace the lights with a set we ordered from you guys but now the backlight works but we can’t get any image to pop up on the screen (not even the LG logo anymore) :/ any advice ?!

  • @user-qd4yy6jq5d
    @user-qd4yy6jq5d Місяць тому

    thank you it worked for me

  • @macartanmcquaid22
    @macartanmcquaid22 Рік тому +1

    Thanks for the video, very helpful as I'm considering taking on this fix for my LG 50" LED TV...
    It's a bit daunting, I didn't think it had so many layers to disassemble to get to the LED strips though...

  • @jullifus
    @jullifus 5 років тому

    Does the same work for LG 55LB620V?

  • @dalebenton3354
    @dalebenton3354 8 місяців тому

    Done this to my Ultra HD 4K TV about 4 years ago,Brought my HD TV from E bay for as little as 99p in theAuction for spares or to repair,£10 for postage,£15 for the replacament backlights,Mean while,A lot of dark shades in the back of the TV screen,Since I replaced the backlights,Then carefully put it all back together again,It's been a perfect working TV ever since,Use it most of the time ever since mostly for internet,Got it up on the frontroom wall,Connected to my gaming Computer

  • @brooklyn5754
    @brooklyn5754 4 роки тому +1

    Hi there does anyone knows if i have to put the reflector shield back because i just bought new leds for the model tv i have but now the holes don't line up with the new led strips

  • @russellmartin3699
    @russellmartin3699 6 років тому +1

    nice job if you never did this before watch it over and over and go step by step

  • @carlangelochan2714
    @carlangelochan2714 4 роки тому +1

    55UF680T LG 55 UHD LED TV do you have led strips for this model?

  • @thuggy67
    @thuggy67 4 роки тому +3

    Guys I fixed my TV
    Thank you so much
    I had to buy the LEDs online

    • @matick6275
      @matick6275 4 роки тому

      Where online

    • @thuggy67
      @thuggy67 4 роки тому

      @@matick6275 Amazon bro. you want the link , I even left a review

    • @matick6275
      @matick6275 4 роки тому

      zac morris yea sure

    • @matick6275
      @matick6275 4 роки тому

      Yea that would be great

  • @munirahmed585
    @munirahmed585 3 роки тому

    Good job sir

  • @sandeepsreevalsan2768
    @sandeepsreevalsan2768 6 років тому +1

    Hi I am attempting to replace the LEDs on my LB47650V. I have a very trivial question. What kind of adhesive tape was used in the video to hold the screens together.

  • @weirdomemes
    @weirdomemes 2 роки тому

    Can you tell me order of those filter layers I have 2 prism and 1 diffuser layer

  • @DSAK55
    @DSAK55 Рік тому

    Excellent

  • @user-uf5po9ng6t
    @user-uf5po9ng6t 5 років тому

    Please HELP : What is the name of the black piece (SCREEN) which located at the beginning of the device .. I have broken this piece and I do not know what i must to write in Amazon to find it , I mean this piece in front tv (Crystal black screen )

  • @dalebenton3354
    @dalebenton3354 8 місяців тому

    Also repaired many other HD TV's before as well,Amount of times ive taken LCD screens out,They so thin,Allmost as thin as paper,Only problem with them,They look like they so easy to break,Taken out a few broken LCD screens before,Done a test with broken LCD screens,By snapping them,Only takes a little snap,So easy to break

  • @xviciousviper5315
    @xviciousviper5315 3 роки тому

    Which Led stripes in need for my Grundig 55" GRB6620 TV i cant find in anywhere and dont want to buy the wrong leds

  • @shepherd7331
    @shepherd7331 11 місяців тому

    I sent my TV (LG 42LB65) to be fixed by an LG-certified repair center here in Egypt. The backlight strips were replaced, but instead of bright white spots, there are slightly dark spots, which can be noticed in video games with large bright uniform scenes. In other words, my problem was mitigated, not completely resolved. When I called the maintenance shop, they told me this is due to the fact that the components of my TV (especially the power supply) are old. I bought the TV, as far as I remember, on 2/2/2015, making the TV over 8 years old at the time of repairing (late May 2023).
    The weird thing is that the sightly dark spots are there despite the backlight being very very bright. Moreover, on some contents colors seem to be "washed out"; too much pale color on the screen, especially UA-cam videos.
    Several technicians I know tell me different things, but most notably that it might be an issue with the quality of the LED backlight strips. The strips I installed are not a genuine kit produced by LG, but a Chinese one. The repair shop told me that the genuine backlight kits are far more expensive and are not available; all those who claim to sell genuine Korean LED backlight strips are lying.
    I need help, can this issue be 100% resolved? Can this issue persist due to the TV being old? I want to fix the issue 100% and have my TV like new again. Do you think someone here is lying to me?

  • @Stevie02101984
    @Stevie02101984 3 роки тому

    Moin mit was für Saugern hast du das Panel angehoben?? Danke schonmal

  • @Metalhead-4life
    @Metalhead-4life 2 роки тому

    Do you know what it means when the LED (LD701) on the back of the power supply board flashes 4 times? This occurs after the backlights turn off.
    I have already bought an LG 55LM5800 Power supply repair kit from shopjimmy (because you were out of stock of the ps board). That didn't fix it so I replaced the main Caps, that didnt help so I bought a replacement power supply board and IM STILL having the same issue, please help?
    After replacing the ps board the backlights power on & everything works for about 20-30 minutes then the backlights turn off.
    Now when I measure the voltages at the led strips>power supply board it goes up to about 70v on both connectors then drops quickly to zero volts. If I place my DMM in Loz mode then the voltage doesn't drop to zero and It reads a steady 71.1v on both connectors. It's an edge lit model btw.

  • @garybennett3256
    @garybennett3256 5 років тому

    My lg tv is blinking.. all the leds but do i have to replace all the led strips? Cheers

  • @domualex
    @domualex 2 роки тому

    hi, can you please help me with the correct order of the white filters? my son played with them and i feel they are not into the right order

  • @tracyburke599
    @tracyburke599 Рік тому

    55LH575A - Prior to installing the new LED strips, the picture was fine, but dim in areas. After replacement, the led lights are working fine, but no image appears on screen. Various colors and lines are appearing and I can see that something is happening as I push buttons, but no detailed image is on the screen. I purchased a new tcon board also, but swapping it out doesn’t change anything

  • @memyselfandi6422
    @memyselfandi6422 4 роки тому +24

    Such a simple problem like a couple of bad led strips and such a long and drawn out and fiddly process to replace them, the person who invented the LED television should be sentenced to life in prison without the possibility of parole.

    • @mateusfolletto6142
      @mateusfolletto6142 3 роки тому +11

      It wouldn't be a problem if they used alumnium strips with thermal paste to diffuse heat and prevent the leds from cooking to death. They use glass fiber strips and put zero measures to prevent overheating, literally building screens to die out in a few years.

    • @shrabonibabu
      @shrabonibabu 3 роки тому +4

      Yes you are absolutely right. The right the early models would cost so much. My 55 inch stopped 2 years. Repaired once for almst 1/3rd cost, but just lasted for six months. Since I stopped watching tv. Thanks for this video, I shall give it a try soon.

  • @MeganBloom
    @MeganBloom 2 роки тому

    Which strips do I need 43uh603v LG or any 43 inch model??

  • @bobs7251
    @bobs7251 3 роки тому

    If I don’t know which LED lights are bad and want to replace them all, how many do I purchase? I don’t know what I’m looking for to fix a 50BG5900

  • @shameshame9772
    @shameshame9772 3 роки тому

    Does it work for aftron android TV.
    How can be sure that the strip or power supply of the led striper ?

  • @danwall690
    @danwall690 2 роки тому

    Sorry if you covered this but I’ve read you don’t go off the Tv model number when ordering new back lights, what do I go off

  • @rickjamesb.
    @rickjamesb. 4 роки тому +15

    You should have shown a moment where you test whether the lights are on before you put the whole thing together.

    • @memyselfandi6422
      @memyselfandi6422 4 роки тому +1

      Maybe they didn't show that in the video but I am sure that they did test it afterwards and I'll bet the television didn't work, so the technician had to do everything all over again.

  • @BIZLATLV1
    @BIZLATLV1 Рік тому

    I ripped one of the clear ribbons attached to the hdtv screen and skinny circuit boards. Am I screwed?