As a novice, just changed my spark plugs. Thank you for the information. I too have watch many video's stating do NOT use anti seize, (I think thats for normal maintenance mileage procedures) however my (new to me) 2014 RAV4 old plugs were very hard to screw out due to how bad the original plugs looked and the very dark residue on each plug, I went a head and added anti seize, however I used extreme small amount. Looking down where the plug goes, lots of carbon buildup. I think I will be using fuel additives for a while as well. Thanks for taking the time to post the video...
@@bundysgarage nope, entire engine is immaculate shape. Only issue I have seen is the boot covers on each of the shocks are desegregated. I got what appears to a very well maintained vehicle, with exception of oil maintenance. Thanks again for your information
Only if you have a misfire and determine the ignition coil to be the cause. Typically only one will fail, I have never seen all 4 fail at once. So just replace the one that is bad. Some shops will quote out changing all 4 but they are scamming you, you only need to change out the one thats bad.
I don't hate you because you put anti-seize on the plugs. I used to be a sports car mechanic and did it myself for years. But if you check the spark plug manufacturer's websites you will find that they recommend against doing it. The main reason they give for this is that the anti-seize acts as a thread lubricant which can and often does lead to over-tightening the plugs, which later on can lead to seizing.
Engine covers are (in my opinion) one of the most worthless things, the engine is something that isn't normally seen. I used to not put dielectric grease on my plugs either. Then one time I had the rubber from the C.O.P stick to the plug to point I thought I ripped it when I took the coil part off. Luckily I didn't but I also struggled with that boot for about 45 minutes before successfully getting it off and removing the plug. After that, I took no more chances and any time I change anyone's plugs; they get grease. I know it is a highly contested topic, but I'm beginning to think of putting grease on the threads as well, before I end up with a stuck plug. Not going to lie, there were a few times that I thought I might have been in that boat. And finally, a question to end this wall of text:P Any particular reason you use a nickle based grease for the plug threads? I have a copper based grease that I still have plenty enough of to use; but if there is an advantage to using the nickle (or disadvantage with the copper) I'll get the nickle grease.
Thank you so much! First time doing spark plugs, your video was very easy to follow with great explanations. Saved $184.25 haha.
As a novice, just changed my spark plugs. Thank you for the information. I too have watch many video's stating do NOT use anti seize, (I think thats for normal maintenance mileage procedures) however my (new to me) 2014 RAV4 old plugs were very hard to screw out due to how bad the original plugs looked and the very dark residue on each plug, I went a head and added anti seize, however I used extreme small amount. Looking down where the plug goes, lots of carbon buildup. I think I will be using fuel additives for a while as well. Thanks for taking the time to post the video...
You are welcome! Glad it helped you out. IS your valve cover leaking?
@@bundysgarage nope, entire engine is immaculate shape. Only issue I have seen is the boot covers on each of the shocks are desegregated. I got what appears to a very well maintained vehicle, with exception of oil maintenance. Thanks again for your information
Great tip on using the tube to guide the spark plugs in.
You're such a great teacher, thank you so much. New sub; supremely grateful follower! 😻
I didn't even think about the engine being warm. Good call. I'll let it cool down
Thanks for the video. I am off to the garage. Pray for me !
You’ll do fine. Don’t be scared!
What are the "All Kinds Of Horror Stories" about using Bosch / German Spark Plugs? LOL😂
Could you use the coil packs to remove the spark plug once it’s loosened or install the new ones?
great video my guy I think I can knock this out. you give me hope. thanks
YOU CAN DO IT!
thanks man, subscribed
Thanks for the sub!
Would it be better if you used turqe wrench
Any reason to change the coil packs at the same time?
Only if you have a misfire and determine the ignition coil to be the cause. Typically only one will fail, I have never seen all 4 fail at once. So just replace the one that is bad. Some shops will quote out changing all 4 but they are scamming you, you only need to change out the one thats bad.
My car is a 2017, and it has iridium plugs, why are you using Platinum plugs? Thanks.
My 2018 owners manual tells you the part number of the spark plug or just go to the dealer and buy them. With spark plugs go OEM.
@@enajenaj6841 i also have a 2018. Just picked up the OEM plugs from Toyota parts. Did you use anti seize?
@@fishkyjelly1020 the Haynes manual sayes you should use anti-seize & rubber hose to aviod Cross threading.
I don't hate you because you put anti-seize on the plugs. I used to be a sports car mechanic and did it myself for years. But if you check the spark plug manufacturer's websites you will find that they recommend against doing it. The main reason they give for this is that the anti-seize acts as a thread lubricant which can and often does lead to over-tightening the plugs, which later on can lead to seizing.
Anti Seize has lead to Seizing?
Anti seize causes over tightening. Just because you’ve always done something doesn’t mean you should keep doing it.
Brilliant. Thank You. Straight to the point. Good mechanical practices. 🦘✌️
What size do we need to remove the first bolts
10mm
@@Jose-so1hxis this included in most tool boxes?
Yes it is
Engine covers are (in my opinion) one of the most worthless things, the engine is something that isn't normally seen.
I used to not put dielectric grease on my plugs either. Then one time I had the rubber from the C.O.P stick to the plug to point I thought I ripped it when I took the coil part off. Luckily I didn't but I also struggled with that boot for about 45 minutes before successfully getting it off and removing the plug. After that, I took no more chances and any time I change anyone's plugs; they get grease.
I know it is a highly contested topic, but I'm beginning to think of putting grease on the threads as well, before I end up with a stuck plug. Not going to lie, there were a few times that I thought I might have been in that boat.
And finally, a question to end this wall of text:P
Any particular reason you use a nickle based grease for the plug threads? I have a copper based grease that I still have plenty enough of to use; but if there is an advantage to using the nickle (or disadvantage with the copper) I'll get the nickle grease.
Shop quoted me $218 for two hours work for what you just showed does NOT take two hours. Sheesh.
You could do it in a hour, taking your time. I use rockauto.com a lot for great deals on name brand parts and spark plugs.
Why wouldn't you just use your magnetic spark plug socket to put them back in?
Cause I want to "feel" that they have started properly, you can with the rubber hose.