hello Gaurav, in the first system you explained spider glass, for the fins are the splice plates recommended at the top most end and bottom most end ? Or should the bottom part of the fin be U channel ? In the first part of your video bottom splice plates were not shown, later bottom splice plates are show, please advice
Thank you for your review. Consider having 2 layers of insulated glass with 16mm. air space in between. Is there an option to place the spider routel in the air space biting only the inner layer while the outer layer of glass is attached to inner layer by structural glazing sealant? In other words if you look to glass from exterior you will see the spider routle concealed behind the outer layer of glass and you can't touch it with your hand
Hi Amin, Thanks for reaching to us. The detail you are looking for is already with many fitting suppliers, and we as a team know this since 2012. Try contacting fittings manufacturers, it will surely help
@@Globaltechniquesofarchitecture Hi. Thank you for your reply... Will be following you for sure for upcoming videos. Thank you for the valuable information...
Hi Saniya, First of all thanks for the query. Spider Glazing, can be done in many ways, Fin being the most favorite of all Architects, but as per our recommendations, we say it must be used for Windload of not more than 1.5-2Kpa, or as a thumb Rule, not above 20-30m as Installation, and maintenance of Glass is too complicated. Hope this helps.
Thanks for reaching to us Parag. your question is too subjective to be replied on UA-cam comments section, you may catch hold of any structural chap, will guide you how to do it, or else ping me on WhatsApp on this No +91 9930952051
How the glass wastage is calculated and what measures should we take during choosing glass panel size for a facde wall for minimum wastage ?( Considering glass fabrication is done in india)
That's very informative Gaurav
Congrats!!!!
Keep guiding us
Thank you so much
Thanks a lot for ur comment 👍
@@Globaltechniquesofarchitecture
Need some tutorials on glass
How will we get learn ?
Please give some guidance
😅😅😂hhh
hello Gaurav, in the first system you explained spider glass, for the fins are the splice plates recommended at the top most end and bottom most end ? Or should the bottom part of the fin be U channel ? In the first part of your video bottom splice plates were not shown, later bottom splice plates are show, please advice
What will be the details of fixation if we turn the alternate glass panels at a certain angle?
Sir kya sirf dekh k pta lagaya ja skta h ki ye ft glass h ya hs if you got time plzzz answer this one too thanks 🙏🏻🙏🏻🙏🏻🙏🏻
Well done Gaurav , you are doing really good job. Lot of people will be benefited.
thanks a lot, bhai
Many thanks for the explanation, would be great to see each of those systems calculated.
Great explanation
Thank you sir for wonderful knowledge sharing
It's my pleasure
Good job
grateful
@ 3:04.....bottom 'Splice Plate"...spelling check.
😄
Hi. Can you suggest the gap between the facade glass in case of a truss spider glazing of height 21 mtrs approximately.
gap has to be such as facade looks, flawless
generally we suggest 100-150 mm Gap
Thank you for your review. Consider having 2 layers of insulated glass with 16mm. air space in between. Is there an option to place the spider routel in the air space biting only the inner layer while the outer layer of glass is attached to inner layer by structural glazing sealant? In other words if you look to glass from exterior you will see the spider routle concealed behind the outer layer of glass and you can't touch it with your hand
Hi Amin,
Thanks for reaching to us.
The detail you are looking for is already with many fitting suppliers, and we as a team know this since 2012.
Try contacting fittings manufacturers, it will surely help
@@Globaltechniquesofarchitecture
Hi. Thank you for your reply... Will be following you for sure for upcoming videos. Thank you for the valuable information...
Yes its possible and i have done project with this system.
Sir glass wastage kaise measure krte h ....
Thank you for the video
adipoli sir
Hi sir, i have sone doubts about facade. Will be so happy if u clarify
Send me ur doubts at globaltechniquesofarchitecture@gmail.com
sir , what is the maximum height of facade upto which glass fins system can be used safely?
Hi Saniya,
First of all thanks for the query.
Spider Glazing, can be done in many ways, Fin being the most favorite of all Architects, but as per our recommendations, we say it must be used for Windload of not more than 1.5-2Kpa, or as a thumb Rule, not above 20-30m as Installation, and maintenance of Glass is too complicated.
Hope this helps.
@@Globaltechniquesofarchitecture thank you sir!
Kis prakar ke steps le jisse glass waste KO kam kiya jaay
How to model facade in STAAD PRO against wind load
Thanks for reaching to us Parag.
your question is too subjective to be replied on UA-cam comments section, you may catch hold of any structural chap, will guide you how to do it, or else ping me on WhatsApp on this No +91 9930952051
I have 20 years facade experience in Dubai and GCC but I have never ever covered this much topic explained in details ..
Great thanks for your efforts
Thanks a lot🙏
9930952051 pls connect on whatsApp
@@Globaltechniquesofarchitecture ok sure i will
Bus sir itne sa doubts h plzz clear agar aap k paas samayy ho toh
How the glass wastage is calculated and what measures should we take during choosing glass panel size for a facde wall for minimum wastage ?( Considering glass fabrication is done in india)
It's a subjective question
Pls call on 9930952051 to clarify your doubts, if u are comfortable
very confused about the tension rod system. Why is the rod in tension?
🙏🙏🙏👍👍👍👍
VS-1 GLAZING SYSTEM PLEASE EXAMPLE
Sir number do apna
9930952051