To be honest this is one of the best built incubator iv seen so far very impressive work man the only thing I did not like was the basket I would put something under it so all the eggs and dropping won’t fall on the bulb and fans as well as the bottom of the incubator
I'm currently working on my Fridge Incubator. I'm not keen on using bulbs for the heat since they tend to retain more heat after reaching running temp. Controller cuts off at 37.5 and the heat continues to rise. I'm using a PTC heater same as a normal incubator but still having an issue with regulating the heat. I'm currently running the SCT-3028 controller which has the DHT11 sensor so now upgrading it to the DHT22 sensor. Thinking about investing in an Arduino to properly calibrate the sensor. I will also be buying a 12v Trigger / Relay / Timer for the egg turner. Wish I could attach a picture here haha
@@junkyardgoodies3994 I'm not using bulbs mate ;) I'm using a 290 degree Celsius PTC heat element. Maybe 290 degrees is too much haha. I might buy a few different elements such as a 170 degree and an 80 degree, then do some more testing. I'm thinking about adding a couple of heatsinks under the heating plate that the element is attached to. There is a lot of heat being transferred through the aluminum frame that I have the heat element attached to, so heatsinks may help to restrict the heat being transferred through the aluminium framing as much....... just different ideas ;) ;)
@@DriftKingToBe wow! You have a impressive set-up mate. PTC heating element is way better than bulbs and more efficient. Thanks for sharing your ideas!
@@hamzahsaidy6688 trays distance is 10 centimeters or 4 inches apart so that you can achieve maximum capacity,but you can adjust more distance for better air circulation. The fans blows upward.Goodluck brother.
Sorry for that part,it happened that the video containing the egg tray turning doesn't support my video editing app. There's a 220v motor at the top of the setter trays that turns every 2 hours or you can set it according to your choice,you can set it on the timer.
I learned a lot from this video. I built my own but it can't hatch Chicken eggs. I can only hatch Guinea fowl eggs. The chicken eggs won't even show that they are fertile after candling. Any help
Ok yung recycled egg incubator mo, ayos alam mo paano. Pero sa itlog bago isalang di ba may limit din sa araw kung ilang days na yan. Kasi kahit mamahalin yung incubator mo at isalang mo more than 2 weeks na konti lang mapipisa. Paki comment kung tama at ano ang tamang gawin. Salamat.
Konti na lang talaga mapipisa pag 2 weeks katagal bago isalang yong fertile egg sir, try mo ng 1 week lang. Sa akin kasi every week ang salang ko. Ang hatch rate ko ay 80-90 percent.
I have a H&N male & female But they are not parents from germany I have parents egg hache Come pullet Female brown male white Am hatch these layer egg Not come like parents colour seperation brown & white Send me a whatz App ur no
To be honest this is one of the best built incubator iv seen so far very impressive work man the only thing I did not like was the basket I would put something under it so all the eggs and dropping won’t fall on the bulb and fans as well as the bottom of the incubator
Thanks for your suggestions bro. I will upgrade it. Happy New Year!
This is really helpful! Thank you!
You're welcome!
Bravo,
this had me so excited for you! I want to do this for my quail eggs.
Thanks, I hope you can build one soon!
What measurements are taken from the egg tray to the other friend egg tray?
@@josueisaiasnieves7231 5 inches center to center
good work
I'm currently working on my Fridge Incubator.
I'm not keen on using bulbs for the heat since they tend to retain more heat after reaching running temp. Controller cuts off at 37.5 and the heat continues to rise. I'm using a PTC heater same as a normal incubator but still having an issue with regulating the heat. I'm currently running the SCT-3028 controller which has the DHT11 sensor so now upgrading it to the DHT22 sensor. Thinking about investing in an Arduino to properly calibrate the sensor.
I will also be buying a 12v Trigger / Relay / Timer for the egg turner.
Wish I could attach a picture here haha
We have the same issue bro! You can fix it by using lower wattage incandescent bulb.i change mine from 40 watts down to 25 watts and it works well.
@@junkyardgoodies3994 I'm not using bulbs mate ;) I'm using a 290 degree Celsius PTC heat element. Maybe 290 degrees is too much haha. I might buy a few different elements such as a 170 degree and an 80 degree, then do some more testing. I'm thinking about adding a couple of heatsinks under the heating plate that the element is attached to. There is a lot of heat being transferred through the aluminum frame that I have the heat element attached to, so heatsinks may help to restrict the heat being transferred through the aluminium framing as much....... just different ideas ;) ;)
@@DriftKingToBe wow! You have a impressive set-up mate. PTC heating element is way better than bulbs and more efficient. Thanks for sharing your ideas!
Just use a pid regulator and sensirion T&H sensor with an arduino. if you tune it correctly it will work.
Nice incubator po
Salamat kabayan!
Is it possible to put fans on top and a heat source? Where do I drill the ventilation holes?
@@NaouiMokhles yes you can install at the upper part, vent holes can be drilled at the upper sides also
Top das galáxias
@@barbosa7255thanks
How did you put the observation glass at the door?
@@erickowaga90 I use a aluminum angle bar to cover the glass.glass size is 10/80 centimeters.i use a jig saw to cut the door.
What's the tray to tray distance?
Does fans blows downward or upward?
@@hamzahsaidy6688 trays distance is 10 centimeters or 4 inches apart so that you can achieve maximum capacity,but you can adjust more distance for better air circulation. The fans blows upward.Goodluck brother.
The best.idol
Salamat idol at sa suporta!
Where do you put the rotator
The motor is at the center connected to the lowest setter tray holder, it's a chain drive and it rotates every 2 hours
I tried that but even the falling still hurts them.
Thanks
@@allanmulindwa8465 welcome bro
Love the idea of using a used fridge, I didn’t get how you made the egg turn rotate side to side though?
Sorry for that part,it happened that the video containing the egg tray turning doesn't support my video editing app. There's a 220v motor at the top of the setter trays that turns every 2 hours or you can set it according to your choice,you can set it on the timer.
@@junkyardgoodies3994 can we set the motor on that STC 1000 or we need to add another timer device?
@@jeewan888 We need to add a Sinotimer brother,then plug your egg tray turner motor into it.
Thank you
Welcome bro!
I want to ask the boss. how many degrees is the slope of the egg rack.???. and the lamp and the fan are made into one cable??? thank you
30 degree angle bro, the bulb and fan have a different connection .
@@junkyardgoodies3994 thanks
@@junkyardgoodies3994 does the fan run nonstop 24 hours???
@@Munadi138 for higher hatch rate bro I recommend you to turn the fan nonstop.
I learned a lot from this video. I built my own but it can't hatch Chicken eggs. I can only hatch Guinea fowl eggs. The chicken eggs won't even show that they are fertile after candling. Any help
Good day my friend! If you can hatch Guinea fowl egg,it means your incubator is good. The problem is in the chicken egg, I think it's not fertiled.
Thanks so much@@junkyardgoodies3994
@@danchengkaba2722 welcome bro
Hi good afternoon I would like to know if you make any of the incubators available for sale and how can I reach you awaiting for your reply
Where's your location ko brother?
Maravilha rapaz
Thank you
pagkapisa sa 21 days bro.,ilang araw pa siya tatagal ,sa loob ng incubator..salamat sa sagot
21 days lang labas na sila dapat sa incubator bro or basta natuyo na lahat ang balahibo nila,iwan mo nlang muna yung mga mejo mahina pa.
@@junkyardgoodies3994 salamat bro.,tapos ano una mo pinapakain sa kanila,booster chicks ba?
@@JHUNSKIETVCHANNEL chick booster bro,saka ka mag-shift ng starter after 2 weeks
@@junkyardgoodies3994 ok bro.salamat sa info
pwede magpagawa?
Location mo sir?
@@junkyardgoodies3994 Laguna Pila
@@ejobsign4310 ang layo ko sir Ilocos..DIY mo nalang sir,madali lang at kompleto ang parts sa online shop.
Kipasnya menghadap kearah mana bro
Facing up bro
Amazing! I'm planning to build one, I hope you can help me brother
No problem bro,just drop a message or send me your email address so that I can guide you.
Kabayan? Location mo if malapit lang baka pwede maview
Ilocos ako kabayan, taga saan ka?
Pokaż jak sprzątasz po inkubacji .
It's easy, just spray or pour water at the bottom. 100 percent water proof, just avoid the electrical parts
👍👍👍
Thank you brother
sir hnd nyo po naipakita kung paano mo nilagay yong device na pampaikot ng eggtray
Hello sir, sorry po hindi po Kac supported ng editing app. ko Yong part na nilalagay ko Yong egg turner nga mga trays at Yong timer.
اخي السلام عليكم ورحمه الله وبركاته كيفك يا اخي
Thank you l
Ok yung recycled egg incubator mo, ayos alam mo paano. Pero sa itlog bago isalang di ba may limit din sa araw kung ilang days na yan. Kasi kahit mamahalin yung incubator mo at isalang mo more than 2 weeks na konti lang mapipisa. Paki comment kung tama at ano ang tamang gawin. Salamat.
Konti na lang talaga mapipisa pag 2 weeks katagal bago isalang yong fertile egg sir, try mo ng 1 week lang. Sa akin kasi every week ang salang ko. Ang hatch rate ko ay 80-90 percent.
I have a H&N male & female
But they are not parents from germany
I have parents egg hache
Come pullet
Female brown male white
Am hatch these layer egg
Not come like parents colour seperation brown & white
Send me a whatz App ur no
I'm a certified breeder of H&N brown nick. The F1 will hatch with color sexing,the female will hatch brown in color and the male will be in white.