I just purchased a Storm 3090 XT and it was surging really bad. I was going to try adjusting the mixture screws (if there were any) but I couldn't even see the damn thing. So, I searched UA-cam and found you. That was such an easy fix...once I pulled everything apart. I didn't have a drill bit small enough so, I tried a few different ways to clean it out but every piece of wire I used kept bending out of shape. I ended up using a piece of wire from a wire wheel (because it was stiff) and it poked right through. I put the thing back in and started it.....RUNS PERFECT!! Thank you for the video instructions👍🏻
@troye.1309 hey thanks for the comment 😊 I'm so glad it helped out 👍 it's like they say 🗣️ knowledge is power 💪 what great state are you from? 🗺️ Michigan hasn't gotten any real snow ❄️ in the past couple years 🗓️ hopefully we get some this year 🤞
@@oakwoodlawnmaintenancellc.1093 I live in Maine. I have a plow on my 4-wheeler but I figured I might as well have a snowblower, too....since the price was right.
Good vid. In the future, I would recommend treating your fuel before you even pour it in the tank. Where I live in New York, non-ethanol fuel is unavailable. So I will add 1/2 ounce of SeaFoam motor treatment, and 1/2 ounce of Sta-Bil 360 per every gallon of gas I use.
Thank you. I just picked up a really nice 5 year old 2620 for $450. It runs great, but it does have a bit of surging. I will definitely be cleaning out low idle jet.
Thanks a bunch for sharing that video! I actually live in Michigan too, in Rochester Hills. I ran into the exact same issue with my used blower. It's been around for about 3 years, and just yesterday, I noticed this rough idle sound. I tried taking apart the carburetor jet, but no luck. Then, I stumbled upon your video and followed your tips. It worked like a charm! The issue is completely gone now, and I'm so happy I found your advice
Thanks fot the video. Mine wouldn't start this year so i dropped the bowl and pulled the jet up in and got it all back together and it fired right up. I was excited till i realized it only ran with the choke half on haha
It is the ethanol blended fuel that causes carburetor problems during storage. Ethanol absorbs water and causes corrosion and gunk to build up in the jets, emulsion tube and float bowl. Sense I started using non ethanol fuel along with Sea Foam in all my outdoor power equipment, my carburetor issues during storage are no more. If non ethanol fuel is not available in your area, it would be a good idea to use some engineered small engine fuel to run through the fuel system before storage. Some say use 91 octane in all outdoor power equipment to alleviate carburetor issues. Small 4 cycle engines are relatively low compression and don't need slower burning high octane fuel. It is the extra detergents in the higher octane E10 fuel that makes the carburetors stay cleaner. Premium fuel still has at least 10% ethanol. Where I live in southeastern MI, 89 octane non ethanol fuel is about the same price as 91 E10 fuel. Nothing worse than the snow blower not starting because of a clogged-up carburetor and a snowstorm is on the way. Sea Foam is a great product to help dissolve varnish and allow it to pass through the jets. That is why it is recommended to be used on a regular basis, one ounce Sea Foam per one gallon of fresh fuel in small engine 2 and 4 cycle engines. If your carb is surging or only runs on half or full choke, Sea Foam recommends a dose of 3 to 1 mixture and turn the engine over to pull the concentrated mixture into the carb and let sit for a day or two to allow the Sea Foam to dissolve the crud. Then, if the engine will start and stay running, run the concentrated mixture out before adding fresh fuel with the regular one ounce of Sea Foam per gallon of fuel.
My model is a "yardworks" but the engine looks the same. I was told it's basically a MTD . Will try this on a warm day. It surges on full speed and wants to stall-out when I slow the throttle down below about half way. Sure hope this works. Clay Oh I already took the bowl off the bottom and cleaned that.
Isn't the idle screw just a stop for the throttle mechanism rather than an adjustment for the jet that it holds in? Also, I don't think the presence of the idle jet has anything to do with EPA regs.
I just purchased a Storm 3090 XT and it was surging really bad. I was going to try adjusting the mixture screws (if there were any) but I couldn't even see the damn thing. So, I searched UA-cam and found you. That was such an easy fix...once I pulled everything apart. I didn't have a drill bit small enough so, I tried a few different ways to clean it out but every piece of wire I used kept bending out of shape. I ended up using a piece of wire from a wire wheel (because it was stiff) and it poked right through. I put the thing back in and started it.....RUNS PERFECT!! Thank you for the video instructions👍🏻
@troye.1309 hey thanks for the comment 😊 I'm so glad it helped out 👍 it's like they say 🗣️ knowledge is power 💪 what great state are you from? 🗺️ Michigan hasn't gotten any real snow ❄️ in the past couple years 🗓️ hopefully we get some this year 🤞
@@oakwoodlawnmaintenancellc.1093 I live in Maine. I have a plow on my 4-wheeler but I figured I might as well have a snowblower, too....since the price was right.
And, it's a month later, and now I have the surging... lol. I did what you instructed... PERFECT !!
Good vid.
In the future, I would recommend treating your fuel before you even pour it in the tank.
Where I live in New York, non-ethanol fuel is unavailable. So I will add 1/2 ounce of SeaFoam motor treatment, and 1/2 ounce of Sta-Bil 360 per every gallon of gas I use.
Thanks, headed down to the garage right now to give it a try!
Great video Rob. Nice work solving the surging.
Thank you. I just picked up a really nice 5 year old 2620 for $450. It runs great, but it does have a bit of surging. I will definitely be cleaning out low idle jet.
Thanks a bunch for sharing that video! I actually live in Michigan too, in Rochester Hills. I ran into the exact same issue with my used blower. It's been around for about 3 years, and just yesterday, I noticed this rough idle sound. I tried taking apart the carburetor jet, but no luck. Then, I stumbled upon your video and followed your tips. It worked like a charm! The issue is completely gone now, and I'm so happy I found your advice
Welp, this sorted my problem, got a deal on the snowblower because of it, now she runs great! Thank you!
sweet find, I have the exact same surging issue, the video was shot very clearly so I can actually follow with my sketchy vision, thanks for the help
Thanks fot the video. Mine wouldn't start this year so i dropped the bowl and pulled the jet up in and got it all back together and it fired right up. I was excited till i realized it only ran with the choke half on haha
For better or for worse I have the flex system and this worked perfect for my surging issue too! Thanks!
Glad to hear that you are doing better. Im in Michigan too. You just reminded me that i better prep my small engines for the winter soon
What part of michigan?
@@oakwoodlawnmaintenancellc.1093 I'm just outside of Flint. Where are you located
It is the ethanol blended fuel that causes carburetor problems during storage. Ethanol absorbs water and causes corrosion and gunk to build up in the jets, emulsion tube and float bowl. Sense I started using non ethanol fuel along with Sea Foam in all my outdoor power equipment, my carburetor issues during storage are no more. If non ethanol fuel is not available in your area, it would be a good idea to use some engineered small engine fuel to run through the fuel system before storage. Some say use 91 octane in all outdoor power equipment to alleviate carburetor issues. Small 4 cycle engines are relatively low compression and don't need slower burning high octane fuel. It is the extra detergents in the higher octane E10 fuel that makes the carburetors stay cleaner. Premium fuel still has at least 10% ethanol. Where I live in southeastern MI, 89 octane non ethanol fuel is about the same price as 91 E10 fuel. Nothing worse than the snow blower not starting because of a clogged-up carburetor and a snowstorm is on the way. Sea Foam is a great product to help dissolve varnish and allow it to pass through the jets. That is why it is recommended to be used on a regular basis, one ounce Sea Foam per one gallon of fresh fuel in small engine 2 and 4 cycle engines. If your carb is surging or only runs on half or full choke, Sea Foam recommends a dose of 3 to 1 mixture and turn the engine over to pull the concentrated mixture into the carb and let sit for a day or two to allow the Sea Foam to dissolve the crud. Then, if the engine will start and stay running, run the concentrated mixture out before adding fresh fuel with the regular one ounce of Sea Foam per gallon of fuel.
Absolutely!
Thank you for your time and efforts sharing this information.
&Thank you so very much for your video. I don't have that problem.... YET!
My model is a "yardworks" but the engine looks the same. I was told it's basically a MTD . Will try this on a warm day. It surges on full speed and wants to stall-out when I slow the throttle down below about half way. Sure hope this works. Clay Oh I already took the bowl off the bottom and cleaned that.
Did it work?
good to see you and i hope your health it getting better and i hope one day u go back lawn care
Absolutely things are getting better thank you.
@oakwoodlawnmaintenancellc.1093 good I am glad to hear that
Isn't the idle screw just a stop for the throttle mechanism rather than an adjustment for the jet that it holds in? Also, I don't think the presence of the idle jet has anything to do with EPA regs.
I just use ethanol free fuel. Never have these problems again.
It’s not important to count how many turns
It looked like the screwhead was tapered the more I would screw it in. The more it would push, the jet in, or I should down in. ✌️
cheap crap