Very good explanation of the DSP on the Yaesu. I just ordered this rig as my backup and portable for remote work. Plan to use it with a solar setup. I have the FT-950 as my base and the DSP on it is the exact same layout and function. I generally run DNR at around 50%, Contour where is simply sounds best to me, Width about 60-70% and then Shift in the center. When I have a signal I am struggling with I narrow the Width and track it down with the Shift. Works great and you can do it in just a few seconds. I have found that pushing the DNR too much only makes it worse but a little does great job. Another great trick I learned is that if you invert the contour (make it a peak instead of a notch) you can really zoom in on a signal as opposed to notching out around it. That is done in the menu function for the contour and I moved mine from -10 to a +10. It even changes the readout to show a peak instead of a notch.
Great Video. Your explanation, tips and overall teaching style kept me engaged, I found myself taking notes and understood your points with enthusiasm instead of boredom. So many videos out there have these hand held jiggling images with zoom in's that always go out of focus, the person looses their train of thought; and what do we have? A waste of time. Instead: Your explanation made the DSP function on my new rig easier for me to understand and go explore on my own. I can't wait to see your other videos on the 450D. Cheers.
I have owned the FT-450, FT-450D, and FT950. The D model is a nice improvement over the earlier FT-450. I will probably trade the FT-950 for an FT-1200, but will keep my FT-450D. It's a really nice radio for portable use as well as in shack. Nice and informative video. Thanks. WB4TJH
Hi, This video help me understand the DSP more than the Manual ..Hi Hi . I have always done the same thing .. Just use the shift to fine tune, But I am going to start using and experimenting with all of the DSP. On a side note , I love the Ft-450D.. It’s a great entry-level HF rig. Thanks for sharing. 73s N4EVG
My suggestion is to leave the Contour and Notch OFF... set the selectivity to wide, and leave the DSP off unless you need it.. then a setting of 3 or less will work except in really bad conditions. Try the noise blanker first, before the DSP. Set shift to center and adjust for best quality. In normal conditions you will not need contour peak or knotch.. DX combat maybe different I dont do that.
I finally brought my 450 D ! No one give so much at that rate ! At 599 euros I got RADIO + DSP + ATU + LARGE COVERAGE MOD + POWER MOD (latest) MAX TX PA 185 WATT ! ALL INCLUDED !!!!!! WOOOOOOWWW !
I sold all of my cheap radios, the rangers, cobras, unidens and purchase a 450d. (Mars mod ) Man , i tell you one thing. It was worth it. The quality is superior to those chinese brands. Filters, DSP, a real working NB , 25watt AM carrier and 100 watt swing. The only radio i have now.
Hi Tonysuper job..I am new to the high frequency bands and just purchased the ft-450D.. Your "How To" get started video is great.I would love to see you do something on setting up the CAT control to use HRD (Ham radio Deluxe) .. It's a real nice program and expands the capability of that radio tremendously.Thanks againDoug/ WA2PBL
I love the 450D, I just wish they would have also implemented an automatic notch filter button like on the Icom IC-718. Other than that, its a great rig for the money and if you have limited space or need portability.
It is a helpful video but, yes, you're correct. There is a metric BOATLOAD of stuff that is behind that control and it is NOT something you want to be spinning the way you would a big VFO knob (as he does a few times). I know, believe me. I didn't cause it, but it had to be replaced on mine early. Under warranty and the service to/from Vertex was PHENOMENAL. Just a caution. Be nice to that DSP knob.
When in the 60 meter mode, how does one go about adjusting the 4 DSP functions (contour, notch, DNR, and width)? The DSP button will allow me to page through the 4 functions, but in 60 meter mode, I can not use the DSP/SEL knob to make adjustments. Can this somehow be addressed through one of the MENU functions?
Hi Dirk, unfortunately I haven't used this radio on 60 meters. In fact, I haven't even upgraded the firmware to allow it, so I can't answer that question. Sorry! Perhaps trying Yaesu technical support- they've been helpful to me in the past.
I don't use hf that often and am looking to buy a rig I have had several in the past and have been looking at the dx1200 but for the price the 450 sure does look nice any thoughts on the 450
i would say the 450d every time for a rig that is good for the price,i have one for 1 year and i know it is good how ever if you don,t want the built in A.T.U get an Icom 7200, one warning the microphone you get with the Icom is not very good.so get the 450d it will be all the radio you ever need,as for the bigger rigs more menu items more fancy lights i call that a bubble gum mechine, don,t like the bubble gum part at all ...
These adjustments are designed to pull in stations that might have interference and or just a weak carrier. If you have a strong signal none of these controls need to be enabled. If you have a weak signal you can usually start at the width control and adjust that to possibly receive better. The DNR or digital noise reduction control can be dialed clockwise and you will hear less static in the receiver. Take a look at your manual and read it thoroughly they do an excellent job at discussing this IF DSP features on the 450 rig. In summary they are adjusted to help receive weak signals. Hope that helps. 73....KD2PGJ
Tony, I have just had my FT450D for 3 weeks, I don't know if the rig has a problem or just me, I can't get the cs button to work for tune up, all I keep getting is VCC13.4 which is my power supply voltage, it was working about 2 days ago, I have done a full reset but still the problem exists, I'm hoping you might have a suggestion, am I missing something simple, Dave
Hi Dave, Not sure what you mean by using the C.S. button for "tune up." To activate the radio's internal tuner itself, use the "Tune" button (press it once to turn on the feature, and hold it down for a second or two to actually start a new tune). The C.S. button is a button you can manually assign to a particular function by setting it up in a menu. It appears you can assign Tune to the C.S., but I'm not sure why you would need to. Page 16 in the manual should help with using the C.S. button. Hope this helps!
Hello Tony,. Thanks for the reply, my tune up method using the CS button is simply I'm using my inv vee for as many frequencies as possible, tuning thru my external manual tuner, I Iike the CS button as it will tx a 10 watt carrier for tuning, quick and less stress on the ft450D for tuning, but for some reason probably too much knob twiddling on my part I have lost that mode, I did get out of the Vcc mode, but now stuck some where else, I think the owner manual will be worn out long before the rig itself, I must admit being a very senior OP, menu systems are not appealing, my last ft817 was great, and also my old TS 130S, I'll even throw in my TS520, fire them up in seconds. Anyhow Tony thanks for your suggestions and the video which I'm sure is very helpful for lot of 450d owners. Dave
I've recently bought one of these, but I find the RX audio terrible & muddy; the only way I've found to improve it is to turn the contour fully down to the left. Out of the numerous rigs I own, the FT-450D is hands down the worst for receive audio. Has anybody else noticed the same poor audio?
Have you tried with a different speaker or headphones ? I usually listen with headphones and it makes a huge difference. I guess I'll find out tomorrow when I get my 450D 🙂
@@kevm666 I gave mine away a while ago, and realised why they're so cheap quite quickly. I now use something significantly better, albeit only a mid-range rig, a Yaesu FTDX10.
+Phil Neale (bootsie) TXPOWER is adjusted through the menu. Press and hold the "F" button, select RFPOWER with the DSP/SEL knob press it once and select 5 to 100W. Press and hold "F" again to exit the menu (it's not as hard as it sounds! ) 73
Very good explanation of the DSP on the Yaesu. I just ordered this rig as my backup and portable for remote work. Plan to use it with a solar setup.
I have the FT-950 as my base and the DSP on it is the exact same layout and function. I generally run DNR at around 50%, Contour where is simply sounds best to me, Width about 60-70% and then Shift in the center. When I have a signal I am struggling with I narrow the Width and track it down with the Shift. Works great and you can do it in just a few seconds. I have found that pushing the DNR too much only makes it worse but a little does great job.
Another great trick I learned is that if you invert the contour (make it a peak instead of a notch) you can really zoom in on a signal as opposed to notching out around it. That is done in the menu function for the contour and I moved mine from -10 to a +10. It even changes the readout to show a peak instead of a notch.
This was very educational for the operation of the DSP feature.
Great Video. Your explanation, tips and overall teaching style kept me engaged, I found myself taking notes and understood your points with enthusiasm instead of boredom. So many videos out there have these hand held jiggling images with zoom in's that always go out of focus, the person looses their train of thought; and what do we have? A waste of time. Instead: Your explanation made the DSP function on my new rig easier for me to understand and go explore on my own. I can't wait to see your other videos on the 450D. Cheers.
I just bought a 459D. Nice to see some of its features explained further, thanks
Thanks for this. I just bought a used 450D as my first HF rig. This was helpful
Thanks for the video... I have the 450AT and learned a few thing on the Contour. Didn't realize I could peak or notch the audio... good job. N6BOB
I was just gifted a 450D. This helped alot. Thanks!
I have owned the FT-450, FT-450D, and FT950. The D model is a nice improvement over the earlier FT-450. I will probably trade the FT-950 for an FT-1200, but will keep my FT-450D. It's a really nice radio for portable use as well as in shack. Nice and informative video. Thanks. WB4TJH
Thank you very well explained.
Have this radio as well and really enjoy the DSP on this rig
I really appreciate this video. Thank you for the thorough job of it.
Hi,
This video help me understand the DSP more than the Manual ..Hi Hi . I have always done the same thing .. Just use the shift to fine tune, But I am going to start using and experimenting with all of the DSP.
On a side note , I love the Ft-450D.. It’s a great entry-level HF rig.
Thanks for sharing.
73s
N4EVG
My suggestion is to leave the Contour and Notch OFF... set the selectivity to wide, and leave the DSP off unless you need it.. then a setting of 3 or less will work except in really bad conditions. Try the noise blanker first, before the DSP. Set shift to center and adjust for best quality. In normal conditions you will not need contour peak or knotch.. DX combat maybe different I dont do that.
I finally brought my 450 D ! No one give so much at that rate ! At 599 euros I got RADIO + DSP + ATU + LARGE COVERAGE MOD + POWER MOD (latest) MAX TX PA 185 WATT ! ALL INCLUDED !!!!!! WOOOOOOWWW !
where?
Xavier Ejarque
Aquì en Italia. En una tienda en el sur de mi pais.
Love the radio and thanks for the great explainer!
good video, you explained the functions of the DSP quite well, Thanks
I sold all of my cheap radios, the rangers, cobras, unidens and purchase a 450d. (Mars mod ) Man , i tell you one thing. It was worth it. The quality is superior to those chinese brands. Filters, DSP, a real working NB , 25watt AM carrier and 100 watt swing. The only radio i have now.
Thanks for time shifted DSP demo!
Nice video. I have a 450 and this helps..
That was very helpful. Thanks for posting.
Hi Tonysuper job..I am new to the high frequency bands and just purchased the ft-450D.. Your "How To" get started video is great.I would love to see you do something on setting up the CAT control to use HRD (Ham radio Deluxe) .. It's a real nice program and expands the capability of that radio tremendously.Thanks againDoug/ WA2PBL
I love the 450D, I just wish they would have also implemented an automatic notch filter button like on the Icom IC-718. Other than that, its a great rig for the money and if you have limited space or need portability.
No
Nice Radio. Bet the width and shift functions would work well on PSK also.
Brillant radio great video
I have the 450d i cant do the peak when i press the select it misses peak and goes to the main blocks in contour ant idea why
Thank you. Nice bit of info
anyone know how to scramble voice FT450D ? need help and refreence about this, many thanks..
Do you happen to know how to tell what current firmware is in the radio and how to upgrade it if a new firmware is out?
that control knob for DSP looks very fragile, so much loose looking movement as you use it.
It is a helpful video but, yes, you're correct. There is a metric BOATLOAD of stuff that is behind that control and it is NOT something you want to be spinning the way you would a big VFO knob (as he does a few times). I know, believe me. I didn't cause it, but it had to be replaced on mine early. Under warranty and the service to/from Vertex was PHENOMENAL.
Just a caution. Be nice to that DSP knob.
can you show notch filter working?
Nice nice Rig!
When in the 60 meter mode, how does one go about adjusting the 4 DSP functions (contour, notch, DNR, and width)? The DSP button will allow me to page through the 4 functions, but in 60 meter mode, I can not use the DSP/SEL knob to make adjustments. Can this somehow be addressed through one of the MENU functions?
Hi Dirk, unfortunately I haven't used this radio on 60 meters. In fact, I haven't even upgraded the firmware to allow it, so I can't answer that question. Sorry! Perhaps trying Yaesu technical support- they've been helpful to me in the past.
OK1AKB
Verry good radio
I don't use hf that often and am looking to buy a rig I have had several in the past and have been looking at the dx1200 but for the price the 450 sure does look nice any thoughts on the 450
i would say the 450d every time for a rig that is good for the price,i have one for 1 year and i know it is good how ever if you don,t want the built in A.T.U get an Icom 7200, one warning the microphone you get with the Icom is not very good.so get the 450d it will be all the radio you ever need,as for the bigger rigs more menu items more fancy lights i call that a bubble gum mechine, don,t like the bubble gum part at all ...
man... my notch doesnt require a gazillion turns..(non- D).
are those adjustmens something you set to where you like and then leave or do you find you need to adjust on a regular basis depending on the day?
These adjustments are designed to pull in stations that might have interference and or just a weak carrier. If you have a strong signal none of these controls need to be enabled. If you have a weak signal you can usually start at the width control and adjust that to possibly receive better. The DNR or digital noise reduction control can be dialed clockwise and you will hear less static in the receiver. Take a look at your manual and read it thoroughly they do an excellent job at discussing this IF DSP features on the 450 rig. In summary they are adjusted to help receive weak signals. Hope that helps. 73....KD2PGJ
Tony,
I have just had my FT450D for 3 weeks, I don't know if the rig has a problem or just me, I can't get the cs button to work for tune up, all I keep getting is VCC13.4 which is my power supply voltage, it was working about 2 days ago, I have done a full reset but still the problem exists, I'm hoping you might have a suggestion, am I missing something simple,
Dave
Hi Dave,
Not sure what you mean by using the C.S. button for "tune up." To activate the radio's internal tuner itself, use the "Tune" button (press it once to turn on the feature, and hold it down for a second or two to actually start a new tune). The C.S. button is a button you can manually assign to a particular function by setting it up in a menu. It appears you can assign Tune to the C.S., but I'm not sure why you would need to. Page 16 in the manual should help with using the C.S. button. Hope this helps!
Hello Tony,.
Thanks for the reply, my tune up method using the CS button is simply I'm using my inv vee for as many frequencies as possible, tuning thru my external manual tuner, I Iike the CS button as it will tx a 10 watt carrier for tuning, quick and less stress on the ft450D for tuning, but for some reason probably too much knob twiddling on my part I have lost that mode, I did get out of the Vcc mode, but now stuck some where else, I think the owner manual will be worn out long before the rig itself, I must admit being a very senior OP, menu systems are not appealing, my last ft817 was great, and also my old TS 130S, I'll even throw in my TS520, fire them up in seconds.
Anyhow Tony thanks for your suggestions and the video which I'm sure is very helpful for lot of 450d owners.
Dave
You are doing a great job with your vid's, keep it up we are getting a lot out of them. 73 KD0SMU
MY FT1000 MP MARK V BLOWS THE 450 DSP AWAY----NO COMPARISON
+Rick Burton It's also twice the price so one would expect it to be better. The common argument is that the 450 is VERY good for it's price.
mwiz100 I AGREE, I SHOULD HAVE WORDED IT DIFFERENTLY ---450 IS A FINE RIG
I think 450D is the cheapest HF radio from the main producers in the market. Your rig is much more $$$.
STILL A GREAT RADIO!
You still here comparing a sporty "japanese car" to a LAMBO costing 500x times more. EPIC FAIL !
Good Job. Thanks. 73 de NR7J
merci ... 73
I've recently bought one of these, but I find the RX audio terrible & muddy; the only way I've found to improve it is to turn the contour fully down to the left.
Out of the numerous rigs I own, the FT-450D is hands down the worst for receive audio.
Has anybody else noticed the same poor audio?
Have you tried with a different speaker or headphones ? I usually listen with headphones and it makes a huge difference. I guess I'll find out tomorrow when I get my 450D 🙂
Learn how to use the if dsp it actually sounds good when u use it correctly
@@kevm666
I gave mine away a while ago, and realised why they're so cheap quite quickly.
I now use something significantly better, albeit only a mid-range rig, a Yaesu FTDX10.
How do u adjust the output power
+Phil Neale (bootsie) TXPOWER is adjusted through the menu. Press and hold the "F" button, select RFPOWER with the DSP/SEL knob press it once and select 5 to 100W. Press and hold "F" again to exit the menu (it's not as hard as it sounds! ) 73
Can you save different power output settings per memory location or is it a global setting that stays until you reset it?
do you know how to use the radio ??? don't look like
Éstos radioperadores, no son como los radioaficionados, No fabrican sus armas.
YOU NEED TO TALK MUCH LESS, TURN THE RADIO UP SO WE CAN GET A GOOD IDEA WHAT IT SOUNDS LIKE---DAM!!!
poor sound on ssb