Hi, just replaced all my dji mini 3 gimbal motors, except for the most bottom one that is glued to the plastic. Camera seemes to calibrate but once i fly it in the air its starts to wobble alot and is not stable., During flight its through warning that gimbal is overloaded. Do i need to use some sort of calibration tool for the motors as you suggest here ?
@@NAM3L3555 le saque una foto antes de ensamblar, si gustas te la puedo enviar, yo tube que volver a sacar esa parte del gimball con un poco de calor y una paleta delgada, luego fui acomodando sin pegamento solo con cinta doble faz para ir buscandole el angulo correcto junto con el joystick, dandole a calibrar, una vez detectado correctamente hice unas marcas y pegue el motor.
i just replaced my gimbal and camera. i bought this used and tried to reset it. I have the RC Screen controller but the drone times out when i try to pair it. I went online, updated firmware on the controller but when you hold the power button for 4 seconds to pair, the controller just counts down the 60 seconds and pair is unsuccessful...
Very clear and precise videos, thank you. I have a 1D010003 Gimbal overload after a small crash, Gimbal wont calibrate and limited Yaw movement? DJI Mini 3 pro. Thanks, Dan
Thank you for video. If i change the pitch motor or cable , do i need calibrate Gimbal? Only special dji offical software with vpn can do it? How much its cost? Thanks
Got the gimble stuck with Error Codde 1D010002... Any idea? Thank you. Camera can rotate during power up, but yaw motor did not move. So still the problem with the yaw motor?
@@djiSolutionsThank you so much for your help. I will try to replace the cable then. I have replaced all the motors, which I bought from AliExpress, so I assume they should be good. Thanks again
Hey now, I replaced the Gimbal motor and the yaw stuff and the cable. Now the Gimbal stuff is running good but the picture is blurry. I cant get the picture to focus. The drone was in a crash. Do you think the camera is bad or is there some sort of adjustment for that?
Great video. I changed the yaw motor that had a broken tab, re-assembled but have no motion to any of the motors. Transmission cable looks to be fine and all connections have been checked and are secured. Any suggestions? Any help would be GREATLY appreciated! Ughhhhh
I broke the yaw arm completely. It is so hard to get the yaw motor out. Have to buy a new yaw arm... Do you think the arrow on the yaw motor matters? The new yaw motor I purchased has 3 arrows...
@djiSolutions no. I have both in my hands. Mini 3 and Mini 3 pro gimbals are different. Mini 3 gimbal is stronger (thicker arms). I don't see its motors inside, but hope they are the same. Props motors are different too. Mini 3 wires are thicker and the props connection differs.
Hello. Thanks for this great video ! Did you know if roll arm is the same between a dji mini 3 and mini 3 pro ? (I have to replace my cracked roll arm on mini 3) Thanks 😁👍
what is the problem if the motor is still having buzzing sound (vibrating) even after successful calibration it still have that buzzing and make a little bit move? also after doing calibration via dji assistant 2, the camera now wont focus :(
Buzzing sound? It mean that motor is not working properly. You should replace it again. About the camera not focus, there 2 problem. 1 is the gimbal camera is not working properly and 2 is camera is broken.
@@djiSolutions already change to new motor 😅 even tried 3 of them. Is it possible that the cable movement inside the gimbal somehow interfere with the motor? Mine is not as neat as in your video. Or is it possible the buzzing is because the camera wont focus?
@@borisbahleda2989 on mine it turns out the cable and the parts of the gimbal is for mini 3, although what i purchased is mini 3 pro. I gave up and let professional took care of it.
I just changed the yaw motor, no error message, but the camera is facing 10 degrees right, not keeping horizon when turning 360 degrees, all calibrations performed (automatic +manual), no change. Any ideas?
I'm runing into the same exact situation right now, the camera is look at one side instead of center, did automatic and manual calibartion, couldn't get fix.Did you ever fix yours?
The point where the camera clips onto the motherboard gets very hot. As much as my finger can't stand it. I guess it's not normal. And the gimbal sometimes makes a grinding noise in some places. There are explanations for all this.?
Hellow sir.. what is the posible reason if your video Shakey and have jello effect.. i already change the 2 motors picht and yaw .. and cable.. thank you ..
The blue mark, I just want to put the motor the same position as the old one. As you see the arrow is on the side but sometime the arrow also at front and back.
@@djiSolutions Could you please tell What would happen if the position of arrow of the new motor is not same with the new motor? After replacement, the gimbal is pointing to one side and is giving gimbal motor overload error.
Could you please tell me the issue.. It has made me crazy. Don't know what the fault is.. Does the arrow mark if not aligned as the previous motor could make the gimbal point to one side and give gimbal motor overload error?
I'm runing into the same exact situation, I forgot to mark the arrow position and the camera its looking at one side as well, did you ever figure it out?@@thewildernesstales6397
My problem is, the gimbal motor and flexi cable doesn't have a problem and when i start the aircraft the gimbal starts to function up and down. But, the error 40002 gimbal stuck is still indicated on the screen. What would be your advice? Thank you! Btw, im from Philippines.
Hello Thanks for your work . my dji mini 3 pro had an little accident after that give me a mistake msg: code 1D010002 stabilizer blocked what can i do?
Thanks four your help . im from Portugal and message to mean : Stabilizer locked : Check that the gimbal cover is removed and make sure that the gimbal can rotate freely in all 3 axes. (Code: 1D010002). How can i send you the photos?
When I calibrate it doesn't go through the steps like that. It just kind of wiggles. Only thing replaced was the rubbers. Do I need to recalibrate with this software?
Thank you for video. If i change the pitch motor or cable , do i need calibrate Gimbal? Only special dji offical software with vpn can do it? How much its cost? Thanks
![Fix DJI Mini 3 GIMBAL STUCK Error 40002 [ Cable Problem ]](/img/n.gif)
Your video it's helping out lots of drone owners. Greatly appreciated!
My pleasure!
Hi, just replaced all my dji mini 3 gimbal motors, except for the most bottom one that is glued to the plastic. Camera seemes to calibrate but once i fly it in the air its starts to wobble alot and is not stable., During flight its through warning that gimbal is overloaded. Do i need to use some sort of calibration tool for the motors as you suggest here ?
You might need to use one of the calibration firmwares from dankdronedownloader.
Have same effect :/
Does the yaw motor go in a specific position with respect to the arrow on its chassis? I ask about the blue mark 5:06 (google translate).
Hola tengo la misma pregunta ?
Por lo visto si tiene una marca y debe ir igual , yo lo he reemplazado y ahora el gimbal no sé centra del todo
@ si, tiene una marca, hay qe centrarla bien
@@NAM3L3555 le saque una foto antes de ensamblar, si gustas te la puedo enviar, yo tube que volver a sacar esa parte del gimball con un poco de calor y una paleta delgada, luego fui acomodando sin pegamento solo con cinta doble faz para ir buscandole el angulo correcto junto con el joystick, dandole a calibrar, una vez detectado correctamente hice unas marcas y pegue el motor.
Welldone sir you are rock star
Thank you so much for your lovely comments 😍
All in one video, good video
Many many thanks
i just replaced my gimbal and camera. i bought this used and tried to reset it. I have the RC Screen controller but the drone times out when i try to pair it. I went online, updated firmware on the controller but when you hold the power button for 4 seconds to pair, the controller just counts down the 60 seconds and pair is unsuccessful...
Update drone and remote controller with DJI assistant. If this not help. Open your drone and check the antenna cable
Good videos, I like your videos
Glad you like them!
Nice video, good job bro
Thank you so much bro
I will try this, thanks for your video
You are welcome 😊
Very clear and precise videos, thank you. I have a 1D010003 Gimbal overload after a small crash, Gimbal wont calibrate and limited Yaw movement? DJI Mini 3 pro. Thanks, Dan
Telegram or Whatsapp us for fix that
@@djiSolutions Thanks, I repaired it now, it was a Gimbal Cable, thanks.
Thank you for video. If i change the pitch motor or cable , do i need calibrate Gimbal? Only special dji offical software with vpn can do it? How much its cost? Thanks
Change cable no need calibrate, change motor yes. Easy fix, Telegram us
Got the gimble stuck with Error Codde 1D010002... Any idea? Thank you. Camera can rotate during power up, but yaw motor did not move. So still the problem with the yaw motor?
It can be 2 things, one is cable and other is motor
@@djiSolutionsThank you so much for your help. I will try to replace the cable then. I have replaced all the motors, which I bought from AliExpress, so I assume they should be good. Thanks again
If I have an Apple MAC computer will this be ok for you to help me
No, everything work with Windows Pc
@@djiSolutionsI’ve down loaded Dji assist 2
Hey now, I replaced the Gimbal motor and the yaw stuff and the cable.
Now the Gimbal stuff is running good but the picture is blurry. I cant get the picture to focus.
The drone was in a crash. Do you think the camera is bad or is there some sort of adjustment for that?
Camera broken. Replace it
Hello brother...where to buy gimbal motors?
Check description
Great video. I changed the yaw motor that had a broken tab, re-assembled but have no motion to any of the motors. Transmission cable looks to be fine and all connections have been checked and are secured. Any suggestions? Any help would be GREATLY appreciated! Ughhhhh
The cable always look fine but it can't tell if the cable is working without cable tester ( link in the description)
I broke the yaw arm completely. It is so hard to get the yaw motor out. Have to buy a new yaw arm... Do you think the arrow on the yaw motor matters? The new yaw motor I purchased has 3 arrows...
It cost matter, you can put any arrow you want.
Hi does it work now? I also changed yaw motor but its buzzing
@@borisbahleda2989No. I finally had to send it to DJI. Sorry.
Can u send me how much the software? Any risks to board?
Telegram or WhatsApp us
What is the program he used on his laptop to correct the gimbal?
Hello, DJI solutions!
Mini 3 gimbal is stronger, than Mini 3 pro. Maybe they are interchangable? Very interesting.
Mini 3 and pro are same Gimbal
@djiSolutions no. I have both in my hands. Mini 3 and Mini 3 pro gimbals are different. Mini 3 gimbal is stronger (thicker arms). I don't see its motors inside, but hope they are the same.
Props motors are different too. Mini 3 wires are thicker and the props connection differs.
@@djiSolutions when I'll crack mine Mini 3 pro, will by Mini 3 gimbal, and ask You for calibration 👍🏻
tanks master 🙏🙏🙏 cuestión : how much it’s the cost to change censores back and front for the dji mini 3 pro ??? 😩😩😩
tks for the video. do you have a video for the firmwarte you commented ?
Sorry don't understand, telegram me
Hello.
Thanks for this great video !
Did you know if roll arm is the same between a dji mini 3 and mini 3 pro ?
(I have to replace my cracked roll arm on mini 3)
Thanks
😁👍
Yes they are the same
Can you help me to calibrate the gimbal? I just replaced it.
Telegram or Whatsapp us
what is the problem if the motor is still having buzzing sound (vibrating) even after successful calibration it still have that buzzing and make a little bit move? also after doing calibration via dji assistant 2, the camera now wont focus :(
Buzzing sound? It mean that motor is not working properly. You should replace it again. About the camera not focus, there 2 problem. 1 is the gimbal camera is not working properly and 2 is camera is broken.
@@djiSolutions already change to new motor 😅 even tried 3 of them. Is it possible that the cable movement inside the gimbal somehow interfere with the motor? Mine is not as neat as in your video. Or is it possible the buzzing is because the camera wont focus?
@@sentosa_K yes the gimbal flexible cable also can case that problem too
Hi does it work now? I also changed yaw motor but its buzzing
@@borisbahleda2989 on mine it turns out the cable and the parts of the gimbal is for mini 3, although what i purchased is mini 3 pro. I gave up and let professional took care of it.
You are right but I buy wrong yaw motor without cover already 😂
It ok, just use that but it abit difficult
❤❤❤ thanks sir
I just changed the yaw motor, no error message, but the camera is facing 10 degrees right, not keeping horizon when turning 360 degrees, all calibrations performed (automatic +manual), no change. Any ideas?
Telegram me, it very easy to fix
I'm runing into the same exact situation right now, the camera is look at one side instead of center, did automatic and manual calibartion, couldn't get fix.Did you ever fix yours?
@@happyhappysheepdid either of you figure this out? Same issue
Sir, your telegram namber please
Same issue, sir
The point where the camera clips onto the motherboard gets very hot. As much as my finger can't stand it.
I guess it's not normal.
And the gimbal sometimes makes a grinding noise in some places.
There are explanations for all this.?
It can be gimbal cable or gimbal motor. You have to find out. Replace the cable first because it cheap and easy.
Hellow sir.. what is the posible reason if your video Shakey and have jello effect.. i already change the 2 motors picht and yaw .. and cable.. thank you ..
Hello, I have a mini 4 pro and it disconnects from the CR in a matter of seconds, what could it be? what will be the solution?
Hi. Thanks for this video. Could you explain something more about arrow and blue mark on the motor ?
The blue mark, I just want to put the motor the same position as the old one. As you see the arrow is on the side but sometime the arrow also at front and back.
@@djiSolutions Could you please tell What would happen if the position of arrow of the new motor is not same with the new motor? After replacement, the gimbal is pointing to one side and is giving gimbal motor overload error.
Could you please tell me the issue.. It has made me crazy. Don't know what the fault is.. Does the arrow mark if not aligned as the previous motor could make the gimbal point to one side and give gimbal motor overload error?
I'm runing into the same exact situation, I forgot to mark the arrow position and the camera its looking at one side as well, did you ever figure it out?@@thewildernesstales6397
Blue screwdriver type please 😢?
I did just like you but on the end I turn on the drone but the camera doesn't calibrate 100% it stays a little bit angled
Telegram or Whatsapp us
Hello sir we want solution on lens fogging issue of mini3 pro please make a video on that 😊
Fogging? I never meet that problem. I used to meet like not len focus 😂
@@djiSolutions my new mini3 pro had lens condensation problem as we dont have any service station here i have to sell it .😔
Hello. What is the name of the part on the right with the 3 anchor points to which you attach your rubber? 2:46
The bubber(Gimbal Shock Absorption Dampers) it's connected on the pitch motor.
My problem is, the gimbal motor and flexi cable doesn't have a problem and when i start the aircraft the gimbal starts to function up and down. But, the error 40002 gimbal stuck is still indicated on the screen. What would be your advice? Thank you!
Btw, im from Philippines.
what is your firmware?
Hi what is the name if the software please
Drone hack
Sir which software to remove error code pls reply, thx❤
hi there need that farmware how can i get that
Lucky for me, I buy motor with cover
Good 👍👍👍
Hello Thanks for your work .
my dji mini 3 pro had an little accident
after that give me a mistake msg: code 1D010002 stabilizer blocked
what can i do?
Error 1D10002 is not stabiliZer blocked. Telegram me and send the photos.
Thanks four your help . im from Portugal and message to mean : Stabilizer locked : Check that the gimbal cover is removed and make sure that the gimbal can rotate freely in all 3 axes. (Code: 1D010002).
How can i send you the photos?
Sir, how to calibrate
Telegram or Whatsapp is
Why I have error 40021?
Error 40021 will appear when you change main Camera or motherboard. So you need to rewrite new camera SN.
@@djiSolutions can you rewrite new camera sn with your software?
@@jefferysvideo Yes, Sure
@@djiSolutions how do I purchase software
Please provide link to firmware
Yes i was looping fit that to
😝 P R O M O S M
When I calibrate it doesn't go through the steps like that. It just kind of wiggles. Only thing replaced was the rubbers. Do I need to recalibrate with this software?
No, it doesn't have any error after change the rubber.
@@djiSolutions thanks, I found out there is no camera serial number, I have to replace the camera it appears.
Thank you for video. If i change the pitch motor or cable , do i need calibrate Gimbal? Only special dji offical software with vpn can do it? How much its cost? Thanks