Fix DJI Mini 3 GIMBAL STUCK Error 40002 [ Cable Problem ]
Вставка
- Опубліковано 29 вер 2024
- Mini 3 and Mini 3 Pro Gimbal Stuck Error 40002 is the Most Error happen. You first should clean the gimbal by Tear it down and Clean it. But Gimbal cable is also cause Error 40002 too.
Cheap Aliexpress Link:
- Gimbal Ptz Signal Cable for Mavic 3/Mini 2/Air/Air 2/2s Mini 3 Pro : s.click.aliexp...
- Mini 3/ Pro PTZ CableTester : s.click.aliexp...
- Mini 3/ Pro Full Set Gimbal : s.click.aliexp...
- Mini 3/ Pro Gimbal Cable : s.click.aliexp...
- Mini 3/ Pro Wing Protector 35G: s.click.aliexp...
- Mini 3/ Pro Wing Protector 25G : s.click.aliexp...
- Mini 3/ Pro Landing Gear : s.click.aliexp...
- Mini 3/ Pro Sticker : s.click.aliexp...
Feel Free to Contact Us for more Information
Telegram : t.me/djisolutions
Whatsapp : +85589898982
Tester Link
Gimbal PTZ Flat Cable Test Tool for DJI Mini3/Mini 3 Pro Camera Coaxial Signal Transmission Flex Line
s.click.aliexp...
Search Code on AliExpress: ALCKGCC4
Thank you! although it was slightly different for the Mini pro it ended up working. So fyi for anyone. If your gimbal starts to stutter/shake midflight cable will eventually fail. I crashed my drone and gimbal still worked for a while after, then it started to stutter during flights and eventually gimbal was failing completely but camera was 100% fine. I replaced the cable today and everything works like new! no error codes to.
Any suggestions for if I did replace the cable, and I still get the Gimbal Stuck error code?
@@maryjteraji Sorry I saw this very late. But no suggestions on my end. That was my first time every opening / fixing a drone. Till this day that what caused my failure.
my Dji mini 3 has ERROR 180016, 180017,180031. errors in the lower visual sensor
help me plase...
i have the same issue on 3......gimbal stuck.check whether gimbal cover is removed and make sure gimbal can rotate freely on all three axes
this is from a landing erros...😁
what can i do....the camera stops moving.
I was able to fix my drone that had error code 40002 after crashed, I watched your video and able to fix it replacing cable for $50 dollars, Now my drone is back flying again. Thank you!
what happened to me is that the gimbal has somesand in it after a crash, it also have some sand in the rotors but I'm managing into cleaning it, but i feel I had to clean the gimbal motors cause it is making them to overload or something like that then I had to stop flying for some time
My gimbal works but no video are seen on the phone display.
Can it still be the cable?
The screen went black yesterday after it said the fly app had bug fixes problem and i could not even start the app then.
I was able to fix my gimbal after replacing the ptz cable. But now I can't focus the camera no matter what I do, even manual focus does not work. Would it be safe to assume that if even a single ptz wire on the camera connector section is broken that it can render the camera's ability to focus as useless? There are about 20 wires going straight to the camera alone. If anyone wants to chime in on that possibility please respond. There are very few threads even covering this. If we could save eachother some money that would be great thanks
Wtf I can’t do all this shit 💀
So you can buy new one to replace them
Amazing tutorial, Thank you so much for detailed walkthrough. I was successfully able to change Gimbal wire. In my case, error 40028 still appears after gimbal calibration and after couple of minutes for flight, I'm getting "Gimbal Motor Overload" warning. Any solution for it?
Where i buy the tools you use ?
You didn’t include the link for the rubber gimbal mounts. It’s all I need 😩
Great detailed video, I’m watching because I have one that will need to repair.
But question aside, what camera do you use to record the videos? Has a great focus on the details!
How find your telegram please😔
I fucking fixed it then when i was about to put back the side case manage to fck it up because was trying to put back the cable I fcking bent the wire of the ptz cable, what a day.
It ok my friend, I know your feeling. But don't worry, broken 4-5 drones, you will become expert 😄
is it just me or did I see a "sister voice message"
Your tools that can open the case of drone . I want to buy it. Please tell me where to buy.
I buy from the market 😂 find any place sell phone repair tools
@@djiSolutions aliexpress u find! but... pay attention to do not buy the wrong cable!!! there are 2 main cables inside, .. flat cable riboon cable
my mini 3 have a 40002 error code then i replace the ptz cable but wont solve my problem still have a 40002 error code my dji mini 3 is 7 days old avoid warranty because of the crashed
what can i do next ?
First thing is change cable then change gimbal
I have changed the ptz cable, yaw motor but still not motion. Any idea on what else issue could be? Camera is working on drone
If you still have stuck gimbal, the problem still not fix. I know if hard to find out without the tools. You should have cable tester tools first. Link in the description
And what is the name of that tool
Was curious about the remote removal of the code? What is the best way to contact?
Check the description
after a crash I have error 40028 gimbal blocked and I have the impression that the rubber has turned over but the gimbal is completely free. Will the video be impacted? can I still drive?
Hi, what happens if you get the code 40002 but not the code 40027, is this still the same issue or could it just need normal calibration?
Perfect. Thx Anysugetion where to get parts from ? Thx
AliExpress
What is this cable called and how much does it costs?
Ptz cable mini 3
Hey. Do I need to remove the top of the drone in order to remove the plastic rubber protectors of the gimbal?
If you have no error codes but your camera gimbal is somehow vibrating when u turn on the drone producing shaky videos
I have one same issue with my Mavick 3 Mini. My sister crashed it, and I saw one of the mini cables ripped apart. Could I not get it solded and joint the cables Back together? I mean, the cut appears at simple eye view. Or do I have to replace the whole cable?
e quando tá no alto já filmando e trava o gimbal ? o que seria
Sorry don't understand
When the drone is turned on, the gimbal does not move and a buzzing sound appears. do you know where the problem is?
It can be cable or gimbal
What Did you do? I have the Same Problem
@@achimmi7164 the problem lies in the flexible cable. and yes you will see after that your drone returns to normal
@@jann_dji thx i buy a new Signal cable
Why you need to replace the shock absorption?
HAHAAHAHAHAHAHAAH I just forgot the foam under the ptz main clip, when i put it back and tightened it works great. From 200 dollars qoute from dji to
Nice work! 😄
Excellent video, thanks
@djiSolutions
what is the size of the 1st two black screws you removed from the battery port? The screwdriver that came with my cable kit stripped the screw head
Lolz 😂
i tried to do ... but, when i completed the task, the camera seems to be offline, dead, black screen. Before, it was working, but one of the axis was damaged. So, did i burned out my camera ? ... btw ... there is a cable (black and red) in 2.35, connected to the camera... i didnt see this cable... very strange ... maybe my drone was a different version.
And... i have recently done this procedure with a mavic pro, and it was a successful! !!!
It ok my friend, broken 3 or 4 drones, you will be come expert
Things are fine!!! The problem was the cable.. Aliexpress sent me a bas cable. I hope next time they send me a good one! Wonderful vídeo!!!! ..the must hard part are to connect the 4 joints ❤
Thanks for the content. In the event of a fall, which is more likely: cable or motors? I have video, but the gimbal is stuck.
Mostly is Cable
@@djiSolutions thanks!!
Fantástico
Thank you so lovely comments 😍
Who the fuck do you think I am
Exactly!