DIY MOSFet Voltage Regulator without Potentiometer just using UP and Down Push Buttons and IRF3205
Вставка
- Опубліковано 11 січ 2022
- #ErCanEverything #MOSFet #VoltageRegulator
In this video, I'm used IRF3205 MOSFet Transistor, 0,56uF (546J) 400V CCB Capacitor, 2,2MOhm Resistor and 2 x mini Push button switch
DIY 20 000 mAh QC3.0 Supported Parkside Power Bank from 20V 4Ah Parkside Battery! Just for $1
👉 • DIY 20 000 mAh QC3.0 S...
DIY Rotating Table Platform from Mocrowave oven motor and Gramophone record holder
👉 • DIY Rotating Table Pla...
PARKSIDE Angle Grinder Extreme Stop vs Fast Stop (which Grinder stops first? Performance or Green?)
👉 • PARKSIDE Angle Grinder...
👇Subscribe to my Channel🙏🙏🙏
/ ercaneverything
Facebook👉 ercaneverything
Instagram👉 / ercaneverything
#DIY
#Homemade
#Inductioncooker
#Inverter
#HighFrequency
#HighVoltage
#HighCurrent
#HeatSink
#Computer
#Parkside
#Lidl
#PowerBank
#StepUp
#BoostConverter
#SilverCrest
#TableSaw
#Fence
#ElectricCircuit
#InductionHeater
#PCBbuild
#Soldering
#HowTo
#ToDo
#Craft
#HomeMaster
#HomeMade - Навчання та стиль
it's a good idea, but if you turn off the power and turn it on, the transistor will not open completely?
Always full of ideas. Great job 👏
Thank You my Friend🙏🤝
good work
Nice and easy! Great video as always 👌🏻
Thank you Dostum🙂🤝🤝🤝
👍
Перфектно. И музиката си подбрал отново добра!
Благодаря Приятелю🙏🤝🤝🤝
Friend you are very talented ... Congratulations on what you do !!!
Thank You very much my Friend🙏🤝🤝🤝
Wow, very simple but does a great job! 😍
Although the capacitor has a low capacity. When I turn it on after a while, the output voltage remains the same as before
@@ErCanEverything That's a nice feature 👌
Hello! I subscribed
👍👍👍😍😍😍
Hello, what is the maximum current that this circuit supports?
105A According to the manufacturer
que capacidad tiene el condensador ceramico?
564J = 560nF
Хайде дай идея как да излъжа резачката на батерии от parkside лидл да мога да си я ползвам с външна батерия не оригинална. Като сложа 10ком резистор между минуса и температурния конектор тръгва резачката. Спра ли обаче остават някакви 2.5волта напрежение между минуса и температурният порт и след около 60секунди изчезват сами тези 2.5 волта и пак мога да я пусна. Как мога да ги елиминирам веднага тези 2.5 волта, така че да мога да я пускам и спирам не през 1 мин? Изключа ли плюса на батерията тези 2.5волта изчезват веднага. Но не е удобно така. Пробвах с диод но не става.
Can I use instead Irfz44n or irf540?
Of course
@@ErCanEverything Please made video for 10W 3V Led dim by knob from single lithium battery
ok but its current regulator not volt because the volt is stable
The voltage remains stable because a maximum current of 8A has been reached and therefore cannot be increased more.
At the end of the video it can be seen that the voltage is also regulated.