Hi bro, this is probably one of the cleanest projects around, good job! May i know what is the max current on input? I am looking for something to use with an old server psu @12v 2500w approx 200amps. your suggestion would greatly be appreciated.
Congratulations sir and thanks for making this video May God bless you sir. This is wonderful working. I used this and its really work once again God bless you
Congratulations - by mounting your MOSFETs on top of the ring mounts, and not using any heatsink compound, you've reduced the power-handling abilities of the MOSFETs by about 60 to 70%. And if you use a power supply of more than about 20 volts, it will be possible to destroy the MOSFETs if you turn the pot all the way up. If you attempt to use this setup for higher currents, you will probably overheat the transistors if you try to put out high currents at low voltages with a high input voltage. Your heatsink is entirely inadequate for the voltages and currents which you claim will work.
Are those eye ring terms for external positive battery inputs??? Seems very likely & reasonably sound schematic, 'cept the over heating / not adequate for high current issues??? Can you elaborate on a high current build for say 12v-24vdc input TO 48v-120vdc high current 50a output
@@readytorvdude1224 You cannot possibly get more voltage out than you put in. And if you somehow have 24 Vdc in and 120Vdc/50 A out, you'll need 250 amps in. I cannot "elaborate" on a fantasy. Even something like 24 volts in/12 volts out @50 amps cannot work with those puny wires.
@@wirebrushproductions1001 thanks for replying. I'm trying to harness the alternator B+ amperage out (2ga awg) into DC/DC boost converters; (12v/150A output thru the boost modules (2 in parallel) to convert into 24v or 36v(30A 1500W max) outputs into a MPPT solar charge controller at PV INPUT. Is this practical??? Wouldn't the lower voltage at PV INPUT ALLOW FOR HIGHER AMP INPUT THERE?
@@readytorvdude1224 "Is this practical?" No. Not only no, but Hell no. The wiring shown is completely inadequate to handle the currents you are trying for. But hey, don't listen to some stranger on the internet who hasn't made a video. The parts are cheap. Build one channel and give it a try. Watch it burn up with your own eyes. Did you know that transistors actually run on magic? It's a trade secret that at the center of each package is a pocket of Magic Smoke, which actually makes the transistor work. The proof of this is the fact that if you let the Magic Smoke out, the part will stop working. Build your own copy of this circuit and prove it for yourself.
I'm watching from Russia. Well done author! Respect! Made simply and reliably! But, there should always be a scheme! Preferably posted separately or in the video itself, at least for 4-5 seconds. Then it will be considered a full-time job, and this is already professional and high-quality! And you will want to watch something else on this channel! . Смотрю из России. Автор молодец! Респект! Сделано просто и надёжно! Но, всегда должна быть схема! Желательно отдельно выложенная или в самом ролике, хотя бы на 4-5 секунд. Тогда это будет считаться полной работой, а это уже профессионально и качественно! И захочется ещё что-то смотреть на этом канале!
Doesn’t the diode prevent the Rgs pull-down resistor from functioning? The Rgs resistor is meant to connect Gate to Ground, but in this case the diode is blocking the ‘gate capacitor’ drain. Theoretically, the potentiometer is acting as Rgs anyway (depending on its position) but it’s not a reliable pull-down resistor due to its variable nature. I assume that’s why the other resistor was added, however the diode appears to make it redundant?
Ola amigo boa noite pelo que vi nas especificações de diferenças entre o IRFZ44N e o IRFZ44 ESSE IRFZ44 E MAIS POTENTE POR ISSO VOU COLOCAR ELE Obrigado
Доброго дня. А можна на вхід подати 24 вольта 10 ампер з імпульсного блока живлення, а на вихід під'єднати компресор автомобільний? Не погорять транзистори.
@homemade_101 what ?dont just say yes. your answer is not clear. it doesnt look like its shrink wrapped it looks like a silicon wire. did u use wire stripper.
@@wunderbar-q6y No idea what he did but cutting a length of wire, removing insulation from the end and making subsequent cuts in the insulation (not the wire itself) and separating by hand to fit what you need is the easiest way.
I've already tried this using even more bigger heatsink but it get damn hot when testing a Car Headlamp. But for 775 DC motor, it's ok. So, it's not 50amps.
could it be the motor turning off on with the commutaion which means the mosfets gates are getting turned off and on fast thus will be cooler. While the straight out resistance load of the bulbs will mean the mos gates are on boarder line off / on which is what generates the heat. Good if you can introduce a pulsed circuit with input caps to store the incoming power when pulsing mosfet is off {to use that solar power moment the mosfet is switched on} and have that above circuit using only one mosfet to control gate threshold trigger voltage of pulsed mosfet. But what do I know, Im here because I blow mosfets and need a decent regulator. Like the joker says "If you want anything done properly - youve got to do it yourself"
Mosfets get hot really fast if gate not on properly - so much so - im surprised some {V8 type lawn mower yank hasnt put a heap of mosfets together to make a smart ass hot plate for cooking eggs - i wonder if its more efficient then an element}
CS150N03 and IRFZ44n which is better ?? I have 3 piece CS150N03 which I collect from UPS circuit . Now I want to make this voltage regulator using this CS150N03 . how about it ??
I made it. It works but there is a issue. show wrong voltage . voltmeter show 4 volt but when we connect 4 volt led then it will no works.but if I give 6+ voltage then it will works . so is is impossible to get accurate measurement . @@homemade_101
Why the metal parts of the mosfets not touching the heatsink and no heat compound applied?. So why did you use a heatsink after all?🤔 But......thanks for the upload.
If I did this, then between the potentiometer and the gates of the transistors I would put a TL431. The output voltage in this case would be ideally stabilized.
Hola ,necesito tener 90vcd a la salida para un motor. Puedo sumar otro irfz44 al circuito y repetir el circuito? Y elevar un poco las resistencias y diodo Gracias!!!
I have made this circuit and i will give 21 volt DC to circuit the output are vary but 47 ohm resistor are burned two time What is the reason behind this fault
Bhai koi asa circuit batao jo input me 60v to 90v 30 Ampere DC lekar output me 65v to 85v 50 Ampere DC dede. Meri gadi ki jo battery he usaka load kam karna he muje jisase ki Range increase ho sake. Possible he kya batao bhai.
@@homemade_101 bhai yah apaka video mene dekha he lekin muje 80v output chahiye aur yah to 60v maximum outpit deta he na. Meri scooter 66v ke niche voltage jane par controller cut off ho jata he .
Hello Can the Ni-CD 3 6V 60mAh battery be charged with a 15V AC buzzer transformer? Subsequently, when the 15V power is cut off, does the said battery trigger the coil with working V 12-15~ working Current 1.9A Frequency 50-60hz? If it doesn't, is it circuited for such a request? Can you make this circuit?
0-30V power Supply 👉ua-cam.com/video/9vWsRIokOIk/v-deo.html
Hi bro, this is probably one of the cleanest projects around, good job! May i know what is the max current on input? I am looking for something to use with an old server psu @12v 2500w approx 200amps. your suggestion would greatly be appreciated.
سلام استاد
استاد ایا ورودی توان DC ما باید ۲۵۰۰ وات باشه
وایا با۶۰ ولت ۵۰ امپرو میکشه اگر نه ولتاژ وامپرش چقدر متشکرم.
a quick display of a drawing would help
Dc 24 watt se chala sakte hai kya? Aur ye long time ke liye chalega ya nahi.
Congratulations sir and thanks for making this video May God bless you sir. This is wonderful working. I used this and its really work once again God bless you
God bless you too
Congratulations - by mounting your MOSFETs on top of the ring mounts, and not using any heatsink compound, you've reduced the power-handling abilities of the MOSFETs by about 60 to 70%. And if you use a power supply of more than about 20 volts, it will be possible to destroy the MOSFETs if you turn the pot all the way up. If you attempt to use this setup for higher currents, you will probably overheat the transistors if you try to put out high currents at low voltages with a high input voltage. Your heatsink is entirely inadequate for the voltages and currents which you claim will work.
thank your advice.
Are those eye ring terms for external positive battery inputs??? Seems very likely & reasonably sound schematic, 'cept the over heating / not adequate for high current issues??? Can you elaborate on a high current build for say 12v-24vdc input TO 48v-120vdc high current 50a output
@@readytorvdude1224 You cannot possibly get more voltage out than you put in. And if you somehow have 24 Vdc in and 120Vdc/50 A out, you'll need 250 amps in.
I cannot "elaborate" on a fantasy. Even something like 24 volts in/12 volts out @50 amps cannot work with those puny wires.
@@wirebrushproductions1001 thanks for replying.
I'm trying to harness the alternator B+ amperage out (2ga awg) into DC/DC boost converters; (12v/150A output thru the boost modules (2 in parallel) to convert into 24v or 36v(30A 1500W max) outputs into a MPPT solar charge controller at PV INPUT. Is this practical??? Wouldn't the lower voltage at PV INPUT ALLOW FOR HIGHER AMP INPUT THERE?
@@readytorvdude1224 "Is this practical?"
No. Not only no, but Hell no. The wiring shown is completely inadequate to handle the currents you are trying for.
But hey, don't listen to some stranger on the internet who hasn't made a video. The parts are cheap. Build one channel and give it a try. Watch it burn up with your own eyes.
Did you know that transistors actually run on magic? It's a trade secret that at the center of each package is a pocket of Magic Smoke, which actually makes the transistor work. The proof of this is the fact that if you let the Magic Smoke out, the part will stop working. Build your own copy of this circuit and prove it for yourself.
음... 출력전류는 좋을지몰라도 부하의 변동에 출력전압이 안정적이지 못할듯하네요.
모터 소리로 봐서도 전압변동이 느껴지네요.
그래 네가 맞아
@@homemade_101감사합니다. 영상 잘 보고 있습니다.
@@신-q9d
PARABÉNS PELA ELEGÂNCIA DO PROJETO.
Thanks!
thank you and Welcome bro
I'm halfway through the video and I'd like to say this is wonderfully soldered nice and neatly done good job
And to mention I have built something similar a voltage regulator using an LM317T instead of the 4 pieces that you use. And it worked only 1 lm317t
Thank you very much!
I'm watching from Russia.
Well done author! Respect!
Made simply and reliably!
But, there should always be a scheme! Preferably posted separately or in the video itself, at least for 4-5 seconds.
Then it will be considered a full-time job, and this is already professional and high-quality!
And you will want to watch something else on this channel!
.
Смотрю из России.
Автор молодец! Респект!
Сделано просто и надёжно!
Но, всегда должна быть схема! Желательно отдельно выложенная или в самом ролике, хотя бы на 4-5 секунд.
Тогда это будет считаться полной работой, а это уже профессионально и качественно!
И захочется ещё что-то смотреть на этом канале!
thank you and welcome.
This is not a power supply, this is a radiator 🔥
This is Voltage Regulator 😅
Radiator and stupidity of the year.
just remove the diode, and no more voltage regulator.
🗿
@@RecehDIY you are right the diode prevent mosfet from re-back hi voltage
what was the reason for using the mounting hardware behind the screws if they are all being screwed down to the same heatsink?
my heat sink is aluminum. but not going current. this material problem.
3:22 is that diode there for some regulation or just reverse polarity protection?
yes.
What is the maximum output amphere(A) ,will it used for spot welding
10A
I really enjoyed this video
thank you bro
Doesn’t the diode prevent the Rgs pull-down resistor from functioning?
The Rgs resistor is meant to connect Gate to Ground, but in this case the diode is blocking the ‘gate capacitor’ drain.
Theoretically, the potentiometer is acting as Rgs anyway (depending on its position) but it’s not a reliable pull-down resistor due to its variable nature. I assume that’s why the other resistor was added, however the diode appears to make it redundant?
Yes, It is no need. but it has used an motor back emf blocker.
Hi, it can replace rheostat 300W to adjust 0-32v?
oky
السلام عليكم
ما هى أقصى قدرة لهذه الدائرة مع الحمل
5A
Ola boa noite posso usar o IRFZ44N Obrigado
yes you can use
Ola amigo boa noite pelo que vi nas especificações de diferenças entre o IRFZ44N e o IRFZ44 ESSE IRFZ44 E MAIS POTENTE POR ISSO VOU COLOCAR ELE Obrigado
Доброго дня. А можна на вхід подати 24 вольта 10 ампер з імпульсного блока живлення, а на вихід під'єднати компресор автомобільний? Не погорять транзистори.
good job looks very clean. how did you strip that blue wire like that? 0:51 or did you use heat shrink wrap???
yes.
@homemade_101 what ?dont just say yes. your answer is not clear. it doesnt look like its shrink wrapped it looks like a silicon wire. did u use wire stripper.
@@wunderbar-q6y No idea what he did but cutting a length of wire, removing insulation from the end and making subsequent cuts in the insulation (not the wire itself) and separating by hand to fit what you need is the easiest way.
@agentorange3774 yeah that seems to be the solution
Bro iss circuit se 12.6 volt lithium battery change kar sakte hai constant voltage and constant current ke sath
yes but not auto cut off
@@homemade_101 ok thanks you
Muito bom 😮🔝
thank you
IRF z44 is heated on 4 ampair current and load 4v volt
🤔
أستخدم 3206
I've already tried this using even more bigger heatsink but it get damn hot when testing a Car Headlamp. But for 775 DC motor, it's ok. So, it's not 50amps.
Try this one : ua-cam.com/video/CK0MXyzSEPo/v-deo.htmlsi=gGxJLo9Md1MJHbgz
could it be the motor turning off on with the commutaion which means the mosfets gates are getting turned off and on fast thus will be cooler. While the straight out resistance load of the bulbs will mean the mos gates are on boarder line off / on which is what generates the heat. Good if you can introduce a pulsed circuit with input caps to store the incoming power when pulsing mosfet is off {to use that solar power moment the mosfet is switched on} and have that above circuit using only one mosfet to control gate threshold trigger voltage of pulsed mosfet. But what do I know, Im here because I blow mosfets and need a decent regulator. Like the joker says "If you want anything done properly - youve got to do it yourself"
Mosfets get hot really fast if gate not on properly - so much so - im surprised some {V8 type lawn mower yank hasnt put a heap of mosfets together to make a smart ass hot plate for cooking eggs - i wonder if its more efficient then an element}
Zabardast informatry video.. thanks
Enjoy
Kindly I ask you can use thermal paste under the mosfate and use inductor at output if yes what is the value best regards
are you need use inductor ?? why ?
CS150N03 and IRFZ44n which is better ??
I have 3 piece CS150N03 which I collect from UPS circuit .
Now I want to make this voltage regulator using this CS150N03 .
how about it ??
Try. I think it is good
I made it.
It works but there is a issue.
show wrong voltage . voltmeter show 4 volt but when we connect 4 volt led then it will no works.but if I give 6+ voltage then it will works . so is is impossible to get accurate measurement .
@@homemade_101
Why do you use insulated screws? you are using conductive ring terminal
nathing
Weldone
Good 👍 job
welcome
Sir g input change hona PE out put fix rahage ya nahi
🤔
Please ans.
just exactly work well as you are showing but why don't you make it with easy PWM ?
Just experiment bro.
Why the metal parts of the mosfets not touching the heatsink and no heat compound applied?.
So why did you use a heatsink after all?🤔
But......thanks for the upload.
Is the center pin of the mosfet grounded to the heat sink ?
yes i
Как может быть входное напряжение 80V если параметры MOSFET DS максимум 55V ?
Yes
E so tenho potenciometro de 50k deve servir correto?
yes no problem
Would I fry this circuit if I used my 58V lawn mower battery? (I want 18V output.).
Looked further at video, answers my question as YES.
@@weatherwash763 yes
Não foi anunciado que era de zero á cinquenta volto? mas ganhou meu LiK.
yes
Necesito hacer un regulador de voltaje de 50 voltios y 3 amperes se podria con este tipo de circuito?
yes
The mounting procedure is wrong, please revise it according to the good habit.
Debes hacer eso mismo, pero estabilizado, entonces es que queda bueno.
Please can i use IRFB4110. Will it work?
N chennel OK
Very good❤
WELCOME
Do you have any controller for hoverboard brushless motor using mosfet?
yes. i will make it
@@homemade_101 Thank you I will be watching your videos
@@luiscz777 welcome
For 50ampare out how many ampares required to input
Kindly must response.
Thanks
It depend your course
Is anything showing on the 3digit led? I can't see anything on it. What was it's purpose?
50HZ not seen camera
thanks for your teach
Welcome bro 😇
Hi, can I use this in 48v, 50amps dc motor for bike , if not than increased the mosfets,
Can't Heating I think.
@@homemade_101 thank u, I first check this circuit, than if some problem than increased the mosfets.
Can I use 6 mosfets in parallel?
yes you can
@@homemade_101and can I use irf840??
Can I use this circuit to run 12 volt small dc motor of record player / turntable ?
yes
If I did this, then between the potentiometer and the gates of the transistors I would put a TL431. The output voltage in this case would be ideally stabilized.
😕
Please confirm the small resistor and the pot are they 47ohms each
yes, pot is 47K . the resistor is 470 ohm.
@@homemade_101 thanks you'v done well
I think just 2 mosfets can also controll this motor...
yes
My transformer is 12 or 24 volts AC. Can I use that? Thank you
yes but after dc
very good video
Thank you bro
Main game 🎯 2 resistance and preset
Thank u for your lovely wishes 🙏 Happy New years 💞🎉 in Advance 🎈❤️
same to you. good luck
hi! why 50A max if each mosfet load 49A? x4, total 196A. what I need to more current? thanks
This is connect parallel. So out 50A normally
why using 4 o them when we can us only one?
Can we use IRF150 for 100 v
N channel ok
Porq no mides la corriente para ver cuánto aguanta?
sorry
I need 310v to fancoil Split .... How many MOSFET i need to put
It does not depend on the size of the mosfet. A suitable MOSFET should be used for that.
Broo what is max amp load we can give?
5A
@@homemade_101 thanks you so much broo
What is the purpose of the diode?
short circuit protection
Itu kaki yang tengah gak terpakai bearti ya kak
Que voltaje tiene en la entrada
24V DC
@@homemade_101 en la entrada y en la salida el mismo voltaje
resistor 47om or 470 om,in video 47om in diskripsi 470 om...???
47ohm
Can i give input supply 100v 30 amp in this circuit ?
50V max
I just see the wiring only, but it cannot drive in 100V, because IRFZ44 only 55V in datasheet...I'm confused
yes bro
Hola ,necesito tener 90vcd a la salida para un motor.
Puedo sumar otro irfz44 al circuito y repetir el circuito?
Y elevar un poco las resistencias y diodo
Gracias!!!
no irfz44 is 55V max. use irfp450n mosfet
@@homemade_101 muy bien y las resistencias y diodo se cambian tambien o dejo.los mismos valores que mencionaste en video?
Gracias
Kya aap aise hi ampere aur volt adjustable bana sakte ho
👉ua-cam.com/video/9vWsRIokOIk/v-deo.html
I can use with rediator 12 volt dc motor ?
Readiator ?
Car radiator motors like baleno DC 12 air cooler ?
12 volt DC air cooler motor like baleno motor ?
apakah bisa menggunakan mosfet 19N20C?
yes
@@homemade_101 thnks
I have made this circuit and i will give 21 volt DC to circuit the output are vary but 47 ohm resistor are burned two time
What is the reason behind this fault
Can you use 470 ohm 5w resistor ? Try
Hi man
Can i make this control with irf740 i have 10 mosfets
yes definitely. You can use
Same resistors?
What happened to the middle pin it does not look connected
it is conncet
What is the point of using srew plastic isolator when you put under cable conector? So in this point is useless.
yes, it is not needed now.
What is the function of the diode, I do not understand its use
Short Circuit protection.
10 amp lod pe aacha kaam korgha kya ❤
yes
Apakah untuk pengunaan tanki seprot dengan daya in 12v dan dinamo motor 10a mudah panas?
try
what input range can I provide?
0-50V 10A
@@homemade_101 and the output?
Sangat bermanfaat😊
welcome
can ı use 9v battery?
12v minim
At 4:18 what does the 10k resistor do? Why is it necessary? It is between gate and source, right? Can somebody explain to me? Greetings
yes, because of the discharge of the capacitor between gate and source.
@@homemade_101 100k would be sufficient
Bhai koi asa circuit batao jo input me 60v to 90v 30 Ampere DC lekar output me 65v to 85v 50 Ampere DC dede. Meri gadi ki jo battery he usaka load kam karna he muje jisase ki Range increase ho sake.
Possible he kya batao bhai.
🤔
@@homemade_101 bhai yah apaka video mene dekha he lekin muje 80v output chahiye aur yah to 60v maximum outpit deta he na.
Meri scooter 66v ke niche voltage jane par controller cut off ho jata he .
Good 👍
Welcome bro..
для 50 а сильно тонкие провода
yep
Can we increase ampere rating by increasing number of mosfets
yes. and it is depend type of mosfet
Input maximum amp.....????🤔🤔
50A
Hello
Can the Ni-CD 3 6V 60mAh battery be charged with a 15V AC buzzer transformer?
Subsequently, when the 15V power is cut off, does the said battery trigger the coil with working V 12-15~ working Current 1.9A Frequency 50-60hz?
If it doesn't, is it circuited for such a request?
Can you make this circuit?
yes can
Could you please make a video of this circuit board with a description? How much money do you want? @@homemade_101
या कितना लोड ले कर चल सकता है इससे क्या क्या चार्ज कर सकते हैं
🤔🤔
Pm me can you to install do sola...
try
Would it be possible to use 12v battery input?
yes, 12v can. but adjusting 0-12V
Problem- when I give supply for 24v then my 10k potentiometer burns please tell solution
try 47K potentiometer 🤔
Make boost converter circuit please.
I have made it.
I mean, high AMPS. 10 to 50 amps.
Input from 3v to 12v, and output more than 100v. (Booster circuit)
why don't you provide audio explanation and circuit diagram?
🤔🤔
poco tuleki izolacyjne ???
🤔🤔
Please test 50A.
nl
I made the same circuit, why the voltage decreases with higher loads?
🤔 how to supply voltage into the circuit ??
12 volt
If you add tl431 in the circuit they are not decrease the voltage
HOW MANY WATTS IS THE 470 OHM RESISTANCE, AND HOW MANY WATTS IS THE 10 OHM RESISTANCE?
THANKS GREETINGS
not 470 ohm it is 47 ohm 2W. 10ohm is 1W
sir i made same but when i connect load the fet are burn 2 time😢
what is the load?
47ohm resistors burns why
plz use 470 ohm 5W Resistor
❤❤❤❤❤❤❤🎉🎉🎉🎉🎉🎉
enjoy
Can battery charging?
Yes