Gutting/stripping the 1980 Toyota Long Bed Pickup
Вставка
- Опубліковано 16 лют 2023
- Today I completely gut the interior of the Oklahoma 1980 Toyota Pickup Long bed. Then I discover that it actually has the optional 5-speed manual transmission and the engine might not be a total loss. Last, I roll it outside for a much needed bath with the pressure washer.
Rusty 1980 Toyota Pickup Truck Long Bed(s) Build Intro: • My Rusty 1980 Toyota P...
1980 Toyota Long Bed Rusty Cab Floors: • 1980 Toyota Long Bed R...
More videos of this 1980 project:
Rusty 1980 Toyota Pickup Truck Long Bed(s) Build Intro: • My Rusty 1980 Toyota P...
1980 Toyota Long Bed Rusty Cab Floors: • 1980 Toyota Long Bed R...
More rusty floor repair (shorter version) • How to Fix a Rusty Car...
Cutting & replacing rusty rocker panel: • How to Replace/Fix Roc...
Removing the Cab: • Disassemble & Remove C...
Removing the engine from bare frame: • Toyota 20R Engine Remo...
Toyota 20R Engine Teardown: • Toyota 20R Engine Tear...
Removing the Bed: • How to: Remove the Bed...
Prepare and Paint a Rusty Frame: • How to: Prepare and Pa...
Update Suspension to install Drop Spindles on 1979-83 Toyota Pickup: • How to: Update Suspens...
Installing Steering Components on Toyota Pickup 2WD/RWD: • How to Install All New...
Install Street Edge 3" Lowering Leaf Springs: • How to Install Street ...
How to install Mini C Notch: • How to Install Mini No...
Remove 20R from truck: • How To Remove 20R Engi...
My used OEM Toyota Parts for sale: yota.6thgeargarage.com/
I don't have Patreon or ask for donations, but you can support the channel with some rad 'Yota gear from my store: 6thgeargarage.com/merchandise/
Instagram: 6th_gear
6thGearGarage
Some other Toyota videos you may find helpful:
Remove 1980's Toyota Pickup/4Runner Dash Pad Cover: • How to: Remove 1980's ...
Rebuild Front Knuckles: • How to: Toyota 4x4 Sol...
Restore/Fix/Repair a Cracked Vinyl Dash: • Part 2: How to Restore...
Remove Toyota Truck Rear Glass Window: • How to Remove Toyota T...
How to clean/Restore Toyota Pickup/4Runner Door Panels: • How to: Clean/Restore ...
Toyota Door Disassemble: • How To: Disassemble a ...
Rebuild front knuckle & replace birfield joint 80 Series: • Toyota Solid Front Axl...
Remove an Entire Toyota Rear Axle Assembly: • How to Remove an Entir...
Install/Upgrade to V6 1" Master Cylinder on 4 cyl Toyota: • How to Install/Upgrade...
Install Toyota Rear Axle Bearing, Oil Seal - WITHOUT a Press: • Install Toyota Pickup/...
Replace Toyota Drive Shaft Center Support Carrier Bearing: • DIY: Toyota 4x4 Drive ...
Trail Gear Hi-Steer install: • Trail Gear Hi-Steer in...
Toyota Pickup Fiberglass Bed Review/Comparison: • Toyota Pickup Truck Fi...
How to Properly Repair Rusty Frame: • How to Properly Repair...
Repairing Toyota Frame - Cut Out & Replace Metal: • DIY: Repairing Toyota ...
Fixing Floor and Rocker panel rust: • Fixing Floor and Rocke...
Remove Headliner in Toyota Pickup Truck: • How to: Remove Headlin...
Remove Toyota Pickup & 4Runner COMPLETE Dash: • How To Remove Toyota P...
Toyota 22RE Engine Teardown: • $100 Toyota 22RE Engin...
22r Compression Test: • How to: Compression Te...
Remove Toyota 22RE Engine & Transmission: • Remove Toyota Pickup T...
Toyota Pickup/4Runner Vent Window Conversion: • How to: Toyota Pickup/...
Toyota 4x4 Transfer Case Rear Flange Oil Seal Replacement: • DIY: Toyota 4x4 Transf...
Replace Pinion Oil Seal in Rear Diff: • How to Replace Toyota ...
Remove Door Panel: • How to: Remove Toyota ...
LED Headlight Conversion: • How to: Install Toyota...
Repairing Toyota Frame - Cut Out & Replace Metal: • DIY: Repairing Toyota ...
Breaking a Rusty Toyota Frame in Half: • Breaking & Cutting Up ...
B-Pillar Trim Removal & Install: • Toyota Pickup/4Runner ...
How to disassemble Vent Window: • How to: Disassemble Ve... - Авто та транспорт
Great job thanks more detail is always appreciated
some of the best off road trucks ever built !! cant wait to see it when its done shes gonna be nice
Might need a hot pressure washer for that undercarriage 😮
Yeah, mine didn't put a dent in that gunk. When I get the cab off, I'll spray it down with some degreaser and try again.
Mine had so much gunk on it that I had to do the pressure washer several times with oven cleaner and still had to come back with a pass of wire brush. On the upside, you likely won't find any rust under that cake!
Really appreciate this video as I got my truck disassembled and I need it to see how to put it back together. Looking forward to some of the parts you post up for sale also.
Good point on the gunk protecting the metal underneath... that steel case W50 should look great!
I had a 94 Toyota Single Cab Shortbed. No rust because it was an Arizona truck but it had a buncha gunk under it like that white Toyota. Would have been a great build but I didn’t have any money and it needed an engine and pretty much all new wiring
That gunk must be a southern thing... I've never seen it on any of the 9 Ohio trucks I've owned.
I can confirm this mirror does work for your pickup, I have the same one on my 82
It was the small plastic lens that I wasn't sure about. I didn't see a part number on it. Do you know if they're still available? I'll stop by the dealership the next time I'm in town and check.
@@6thGearGarage I don’t know what part number it is but those mirrors I sent do come with the plastic piece and it does fit the oem mirror.
Rust, equals part out & then to the junk yard!
Yep, that's the plan!
Great videos man. I have a 1985 Toyota pickup and it's actually very solid. Interior is mint. The bed is rusted on select spots. I need some bed side section to cover up some holes. Would you sell some of the scrap sides?
The body lines of this bed are different from the 84 to 88 trucks. However, you can use door skins from an 84-88 to repair the bed sides. Are you in Ohio? I have a pair of doors I'd sell cheap.
the air conditioning on the Oklahoma is an aftermarket system, likely installed at a aftermarket up fitter after the truck was sold, I actually have the hard to find aftermarket 22r/20r sanden sd508 compressor bracket that was paired with those aftermarket a/c systems. also with the transmissions the w55 is a more stout transmission than the w50, I would go with the w55 transmission.
I need to crack open the W55 and take a look. It's super sloppy at 300k+ miles and I never got to drive the truck to see if it shifts smooth. That will make for a good future video. I decided I'm not going to run AC in the truck, seems like more trouble than it's worth when it's not a daily driver. Maybe if I lived further south.
@@6thGearGarage a/c is actually stupid easy to install on these old trucks. You have the hardest to find part, the evap box but if it's not a daily I can understand forgoing it. The w55s are stout. I had one with 350k on it, it still shifted smoothly and with the exception of a bad input shaft bearing it still worked great.
If you have a point of contact I'll send you photos of my bed. There's not huge section just like 6"x 6" spots on either side. The tailgates are readily available aftermarket. Mine is so rusted it's not worth saving.
My 80s L43 transmission looked exactly like that. Could not get the gunk off.
I'm gonna have to let this one soak in some kind of nasty mix of simple green, gas and parts cleaner I think
hell ya
Parts for your store...the spare tire tools, hook tool in cab and bed...is that the oem tool bag in the bed? Was wondering if we'd hear from you, being in Ohio with no air to breath, water to drink....
All good here, I live up by Sandusky, but the situation in East Palestine is a huge mess! I'm slowly going to be adding these things to my store, but I have boxes of 84-88 parts to go through first. I did photograph a hook tool this week and I'll be adding that to the store soon. More to come when I get a chance!
3d print one for your mirror 👍
I need to get into 3D printing...
@@6thGearGarage Yes me too, they are reasonably affordable i think... but to develop stuff for one to print, takes some learning curve i guess. 😁 But i think many 3d models of things are being shared online😁
Good Luck
Do you have any parts for sale ? I need Gas pedal. key with key ignition switch. 0EM radio ?
Yes I do, 6thgeargarage.net/yota/ but I don't have any of those at this time.
12:16 I'm really unsure if that bit was sarcasm or not.
It looks like holes in the chasis to me.
But also there's no road salt used in my country so what we consider rust and something to walk away from is different from Ohio.
There are some holes that were put there by the factory, but no holes from rust. Plenty of light surface rust though, which I look forward to showing how to refinish in a future video :)
the early toyota Hilux
Yeah Hilux to the rest of the world, Pickup in the US. Wish they just kept calling it the Hilux here, it sounds much better.
Shipwreck