Все гениально и просто! Молодец! Вот только упустил один момент, нужно как -то на основание верхнего вала соединить еще круг из фанеры чуть диаметром больше чтобы наждачка не слезала, а остальное все класс. Надо себе такое сделать, возьму на заметку.
Very good ........ But I think you'll have to put something to avoid the tape getting out ..... Notice that from 17:30 on the top of her docking it gets very variable and I think That she can leave causing in an accident .... a little modification in that part ..... and it will be 100% ..... !!!
The problem is the aligment of the wheels and the tighten of the sand paper, You can`t use spring to tighten this, it has to be a solid state with option to adjust. The sand paper also need to slide to center of the rollers, this is achieved by making the rollers not flat all the way, the rollers need to have a higher point in the middle. You can also fit rubber on the rollers for better grip. The sand paper is glued together, you can also use strong thin tape on the backside of the sand paper. No problem to make a little safe guard for the upper roller. Another thing, what is the point of having two of the same thing, I just don`t see the point. The common thing to make here is one table flat or horizontal and one disk grinder. in this option there is the disk and the vertical sander, both the same. Lay down the vertical sander (with modification) and you have a great sander for all things, even long materials. Take or make a box with a lid make options for adjusting the high for the sandpaper, the paper laying flat to the surface inside box, adjust paper high as you go. lead the materials over the table, just like that :)
There are a no. of solutions, remove/ strengthen (stronger spring???) Rigid etc. To prevent the belt slippage, he could use a bicycle inner tube and cut into 1-1.5" bands and he could slip them over his drums. Whilst he's at that, he could maybe increase the centre line of the drum by adding an inner band e.g 5mm to sort of give it a ridge. than add he outer sleeve mentioned above..... well it worked for me on a similar problem. Misty you could also make yourself a guard to prevent the belt slipping off the upper drum and he could add an outer piece of wood to attach to the nut for the drum and add an arch for the nut to travel when it tensions. BOTTOM LINE, MISTY'S TO SOLVE :) Many here are armchair critics who've never built anything in their lives but presume to know it allllllll !!!!! hahahaha..... now we wait, who shall bite...... :)
Good concept and work. I need this for my work and would like to make one with the sander disk just below the work surface of the belt sander to avoid finger injury..
nice build, however seems to me is really hard to change the belt , because you put to many obstacles in the way of that belt . In any case , good ideea , thank you for sharing !!!
Great DIY , Placing a wooden block between belt will hold the object against sand paper, it'll be easy to sand. Attaching another wooden block to the upper wheel will stable the belt.
wow! very cool diy. thumbs and a new sub for you 4sure!.even could take it one step farther and use a glass plate as a 2nd platen to get it even more flat of a sanding surface
Done well with the resources you have, you should have also considered track adjustment, little modification to upper roller and swing arm is all that needed. Appriciate your work, just keep your mind sharp and let imaginations flow in. In no time you will be the best!
Just one ttp to add: @ 5:25 When striking threaded bolts or rod with a hammer, first put the nut on so that the nut is proud of the end of the thread, and the starter threads are never taking a strike from the steel hammer. That preserves the starting end.
Brilliant, thank you! Wondering if there is a way to make the platform adjustable so you could sand at angles (e.g. 45, or 30 degrees). Also, what is the link to build the drill press :-)? Thanks again for a great video.
This is excellent; good design, really like it.The only thing that's a limitation is that you have to have a drill that's got the cylindrical shaped portion of the body just behind the chuck to clamp it in place. Maybe the overall design, as good as it is, could be altered to accommodate a regular electric motor( I have one that I'd love to put to use!!) Is there any way to get a list of the hardware needed(eg. bearings, shafts, etc.)?
Pretty good...but high rotation seems to be required for this drilling mache. In addition, I think you should add a dust protection considering that your drilling vent is placed in horozontal position; consequently while sanding, all dust will lay on its vent opening easily. That's what I think.A small shelter certainly will solve that problem! Good job anyway !!!
Most other DIY belt sander solutions with wood pulleys ive watched have made them a litte convex in profile. i.e. for the axial width of the pulley, its a little higher in the middle vs the outer faces/edges
The ideia, here is very good, and funcional! It´s up to everyone of us to make one like, and alter what needs, to oné`s needs... I have shared your project on my faceBook page
Being a man that has very little money I would love to make this I can get everything to make it but is there a chance you could give me the plans and measurements please. I love watching your videos they help me out a lot, they inspire me to be able to make useful tools for pretty much nothing
I love your work and design, I used to draw the design but never make it real. So simple and easy to install. Please let me copy your design okay and put a little modification.
For Dimension And More Information, Click On This Link :- mistrymaketool.com/make-a-belt-sander-and-disc-sander-machine/
Покажи размеры
Simple and elegant. Thank you for not wasting time showing all cutting and drill steps. Great video
Молодец,какой молодец!!! Спасибо и добрые пожелания из Сибири!
Great job and use of resources. I grew up with my Dad building tools and farm implements when needed. Thank you for the video and inspiration.
Отличная работа!!! И самое главное просто и доступно! Благодарю!
Все гениально и просто! Молодец! Вот только упустил один момент, нужно как -то на основание верхнего вала соединить еще круг из фанеры чуть диаметром больше чтобы наждачка не слезала, а остальное все класс. Надо себе такое сделать, возьму на заметку.
И столешня должна быть чуть выше бокового наждака
Гриндер из дроооов!!! Универсальный. Молодец.
PERFECTO....!!!! GRACIAS DESPUES DE VER TANTAS LIJADORAS...... ESTA SERA LA MIA.... MAÑANA LA HAGO...!!!!
Very good ........ But I think you'll have to put something to avoid the tape getting out ..... Notice that from 17:30 on the top of her docking it gets very variable and I think That she can leave causing in an accident .... a little modification in that part ..... and it will be 100% ..... !!!
I also noticed that. But how would you do it? I would also like to know how to stick the sandpaper. Do you know? Hugs
The problem is the aligment of the wheels and the tighten of the sand paper, You can`t use spring to tighten this, it has to be a solid state with option to adjust. The sand paper also need to slide to center of the rollers, this is achieved by making the rollers not flat all the way, the rollers need to have a higher point in the middle. You can also fit rubber on the rollers for better grip. The sand paper is glued together, you can also use strong thin tape on the backside of the sand paper. No problem to make a little safe guard for the upper roller. Another thing, what is the point of having two of the same thing, I just don`t see the point. The common thing to make here is one table flat or horizontal and one disk grinder. in this option there is the disk and the vertical sander, both the same. Lay down the vertical sander (with modification) and you have a great sander for all things, even long materials. Take or make a box with a lid make options for adjusting the high for the sandpaper, the paper laying flat to the surface inside box, adjust paper high as you go. lead the materials over the table, just like that :)
Wheels should have been made by wood lathe with ledges on both sides.
There are a no. of solutions, remove/ strengthen (stronger spring???) Rigid etc. To prevent the belt slippage, he could use a bicycle inner tube and cut into 1-1.5" bands and he could slip them over his drums. Whilst he's at that, he could maybe increase the centre line of the drum by adding an inner band e.g 5mm to sort of give it a ridge. than add he outer sleeve mentioned above..... well it worked for me on a similar problem. Misty you could also make yourself a guard to prevent the belt slipping off the upper drum and he could add an outer piece of wood to attach to the nut for the drum and add an arch for the nut to travel when it tensions. BOTTOM LINE, MISTY'S TO SOLVE :) Many here are armchair critics who've never built anything in their lives but presume to know it allllllll !!!!! hahahaha..... now we wait, who shall bite...... :)
Very nice. Thank for video
Good concept and work. I need this for my work and would like to make one with the sander disk just below the work surface of the belt sander to avoid finger injury..
Great video
nice build, however seems to me is really hard to change the belt , because you put to many obstacles in the way of that belt . In any case , good ideea , thank you for sharing !!!
I think thats no problem. Thats why he used a hinge in front of the discsander.
Excellent job. Very good material for those who are interested to make this project. God bless you.
It's pretty amazing what you can accomplish with nothing more than a handful of parts, and some scrap wood. Fantastic job!
Great DIY , Placing a wooden block between belt will hold the object against sand paper, it'll be easy to sand.
Attaching another wooden block to the upper wheel will stable the belt.
Ничего лишнего и не заморочено. Так держать.
Show, 2 em 1, parabens e gratidão por compartilhar irmão!!!
Ich find es so GEIL, einfach, nur Abschnitte genützt, keine Farbe nötig, was will Mann mehr???
Einfach Top Top Top 👍👍👍👍👌👌👌👌
I'm brand new to your channel and I couldn't be happier, you explain everything very clear and concise thank you so much
wow! very cool diy. thumbs and a new sub for you 4sure!.even could take it one step farther and use a glass plate as a 2nd platen to get it even more flat of a sanding surface
Agree- needs more belt support
Gracias por enseñarnos a aprender y regalarnos su tiempo felicidades de Aguascalientes México Francisco Gámez 👍👍👍
Done well with the resources you have, you should have also considered track adjustment, little modification to upper roller and swing arm is all that needed.
Appriciate your work, just keep your mind sharp and let imaginations flow in.
In no time you will be the best!
I also noticed that. But how would you do it? I would also like to know how to stick the sandpaper. Do you know? Hugs
so nice idea,..you're so creative.....gimme five
с права можно добавить стенку с подшипником, чтобы уменьшить давление на вал дрели и уменьшить биение
Just one ttp to add: @ 5:25
When striking threaded bolts or rod with a hammer, first put the nut on so that the nut is proud of the end of the thread, and the starter threads are never taking a strike from the steel hammer. That preserves the starting end.
very good job great
Muy bueno , sencillo y práctico. ¡¡¡Felicitaciones desde Santo Tomé - Santa Fe - Argentina
Edie D
Edie Daniel Duré
Great, great, great job. And easy. Thank you from Brazil
Super, simple à faire et complète : Merci beaucoup
Brilliant, thank you! Wondering if there is a way to make the platform adjustable so you could sand at angles (e.g. 45, or 30 degrees). Also, what is the link to build the drill press :-)? Thanks again for a great video.
may i know.. is it okay for the drill to spin for a long period.
Muito show
A melhor lixadeira de bancada
Vou fazer
Very good ... Very great work
Một ý tưởng sáng tạo rất có ích trong cs
I really like your videos. You give people ideas on how to make tools using basic things. Well done. Keep it up
This is excellent; good design, really like it.The only thing that's a limitation is that you have to have a drill that's got the cylindrical shaped portion of the body just behind the chuck to clamp it in place. Maybe the overall design, as good as it is, could be altered to accommodate a regular electric motor( I have one that I'd love to put to use!!) Is there any way to get a list of the hardware needed(eg. bearings, shafts, etc.)?
Really well done that’s what I call doable diy at home
Дрель дрова и куча станков молодец
Pretty good...but high rotation seems to be required for this drilling mache. In addition, I think you should add a dust protection considering that your drilling vent is placed in horozontal position; consequently while sanding, all dust will lay on its vent opening easily. That's what I think.A small shelter certainly will solve that problem! Good job anyway !!!
If you make the support tables as closed boxes you can drill a hole to fit the hose of your vacuum cleaner to suck up all the dust when sanding stuff.
Best work I've ever seen in my whole life!!! 👍👍👍
Es la mejor idea que visto voy a tratar de hacerlo
Bonjour dommage il manque toutes les dimensions de chaque pièce utilisé sinon bonne idée
exelente aporte muy util y muy sencillo,felicidades,eres un genio
Amazing. Your creativity is wonderful
i feel your idea is simple and very useful.i want a edge sander . make a edge sander
não tem como não deixar o meu like!!! Meus sinceros parabéns!
Perfeito amigo obgdo! Parabéns! Deus te abençoe!
My compliments from a 40 year machine designer.
Very good and easy i will make one ..its two in one..
This gonna be very useful for me, thanks a lot for sharing
That is one inspiring video. Definitely gonna try and make my own now.
All ingenious - it is simple !!!
As in this video!
Now that you have finished your cool gadget, you can give it a nice paint job.
The dislikes came from sanding machine companies. 😅😅😅
Nice video ! This helps me a lot with my future projects
Надо замутить такой же, только движок на 180 ватт поставлю заместо дрели
kreasi bagus,,,,, top, ijin mempraktekkan gan...
Well done, you work smart!!! my respect.
Excelente trabajo , como se hacen los rodillos.
Wow amazing .i will try this
That was brilliant and even I could do that Thank you.
Great job,needs to get,his drill
light,focused,
Show!!!Vou copiar sua idéia
Kecil praktis. Amazing
a slider with a swiveller stand might be awesome for the disk sander .
megustaria tenerlas medidas de tu proyecto muy bien te felicito una obra de arte gracias desde venezuela jairo plaza
Perfect!!Congratulation,you are the best!
Muito engenhoso, parabéns!
A beautiful idea, and very well done !!
Woow cool idea. But I have a little question about it. How do we adjust the rail drums to the belt not fly off.
Most other DIY belt sander solutions with wood pulleys ive watched have made them a litte convex in profile. i.e. for the axial width of the pulley, its a little higher in the middle vs the outer faces/edges
Muito bom seu trabalho gostei vou faze uma para mim
PARABÉNS PELO PROJETO QUE SERÁ DE MUITA UTILIDADE NA MINHA OFICINA, GRATO
Muito bom!!!!!!! É Disso que estou precisando! Obrigada!
Brilliant mistry bhai:-) thank u
yes a grove in wheel should take care of that :-)
Mahendra Tiwari .V
Measurements would be a gd thing
Молодец,Красота.
Great build
Gostei muito ficou top parabéns
Thank you for sharing you ideas.
Excellent and smart job!!
Молодец, классно!
The ideia, here is very good, and funcional! It´s up to everyone of us to make one like, and alter what needs, to oné`s needs... I have shared your project on my faceBook page
Ottimo attrezzo complimenti
Super kreativ.
mantap 👍👍
Very well, I'm going to make one but including dust extraction
You very smart..👍👍 i like it..
а фонарик то какой точный) прям в цель бьёт)
how do you adjust the centering of the belt on the rollers?
muy buena idea muchas gracias
Very...very..nice..good joob...insfairing...👍👍👍☕
Aí é sabido parabéns gostei muito
Muito bom suas invenções vc é de onde mano
Question, will it work to grind steel stocks for knives? thx
what type of bit yuo use for steel
xem hay đó bạn
Being a man that has very little money I would love to make this I can get everything to make it but is there a chance you could give me the plans and measurements please. I love watching your videos they help me out a lot, they inspire me to be able to make useful tools for pretty much nothing
I love your work and design, I used to draw the design but never make it real. So simple and easy to install. Please let me copy your design okay and put a little modification.
nice i like to make one do you hace the plans,dimension and measurements. thanks
Impresionante 👍👍