How To | 2013+ | Buick/Chevy | Encore/Trax | Valve Cover

Vehicle In This Video: 2017 Buick Encore
1.4L (GAS)
Valve Cover Gasket Replacement Service
How much does a Valve Cover Gasket Replacement cost?
On average, the cost for a Buick Encore Valve Cover Gasket Replacement is $135 with $40 for parts and $95 for labor. Prices may vary depending on your location.
What is a valve cover gasket and how does it work?
Each cylinder head on your car’s engine has an aluminum or plastic valve cover bolted to it. Between this valve cover and the cylinder head, there is a gasket that keeps engine oil from leaking out. The valve cover bolts keep the gasket compressed, thus preventing leaks. Over time the gasket becomes brittle from the engine’s heat or the bolts loosen, creating an engine oil
leak.
When to consider replacing a valve cover gasket?
Look for these signs of oil leakage at the valve cover gasket:
Oil seepage or dripping. Should the joint between the valve cover and the cylinder head fail, oil often becomes visible on the valve cover or cylinder heads. Usually, the oil will attract and hold dirt.
Oil accumulating inside the spark plug well. The spark plug tube seals are part of the valve cover sealing system. If the tube seals are leaking, you will see oil on the spark plugs or wires. The valve cover gasket and tube seals are all replaced at one time if either fails.
Oil leakage at the rubber grommets. The bolts holding the valve cover to the cylinder head sometimes have rubber grommet seals under the bolt heads. If these seals are leaking, you will see oil seepage around the bolt heads.
Support Us On PATREON: bit.ly/3qQsO07
Support Us On PAYPAL: bit.ly/3r4DPdJ...
--------------------------------------TOOLS I OWN--------------------------------------
Wheel Stud Installer amzn.to/2TQkstm
Stretch Belt Tool amzn.to/3e8bYVk
Gear Wrench 1/2 Socket Set amzn.to/3e6XDIv
Disposable Gloves amzn.to/3e3Bc6Y
Toyota/Lexus Oil Filter Tool amzn.to/3k6wuti
Vacuum Brake Fluid Bleeder ​​amzn.to/3xzATZB
Gearwrench Ratcheting ​​​​amzn.to/2Vm2kHU
7-Piece Spare Tire Retrieval Tool Kit amzn.to/2VlKWmE
Oil Filter Wrench Wrench Kit amzn.to/3ARUjLi
Oil Filter Pliers ​​amzn.to/3yENJpo
Craftsman 1/2 Impact Sockets Set ​​amzn.to/3e5z92e
Screw Driver Set ​​amzn.to/3hYt5K5
Hand Impact Driver Set amzn.to/3yFdF48
Dual Piston Brake Caliper Push Tool amzn.to/3yJDe47
Wind Back Brake Caliper Tool Set amzn.to/3yKGlsJ
--------------------------------------------------------------------------------------------------------
If this video helped, let us know in the comments, and if you liked this tutorial, leave a like and subscribe fore more content like this! Thanks for watching!
Repair Tips & Secrets Only Mechanics Know
DISCLAIMER: This video description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission.
#howto #diy #automotivedysfunction #buick #chevy #encore #valve #cover #gasket #howto #diy

[@pitobansheePR]

Why cleaning the valve coven when you can change it , is very cheap to do it !! That way you don’t have problems with a diaphragm failure and a bunch of codes.. good job and thanks !!

[@jatx5126]

What’s the spray you used to clean? What’s that other part broken you had to replace? What you used with the drill to scrape leftover material?

[@melaniegonzalez315]

Gracias ermanos gracias me sirvió mucho dios te bendiga

[@davidj.zamora5017]

Gasket I got from felpro has oil rings where do they go

[@italianozuzu1232]

Nice 👍

[@bricehale6593]

Hi im doing the same job right now for my mom do u remember what size f e- torx that is

[@camilledarley2420]

71 in lbs

[@scottgarvy]

What are the torque specs on the bolts? Did I miss that I'm the video?

[@scottgarvy]

in the video....

[@AutomotiveDysfunction]

Yes It’s in video

[@scottgarvy]

@@AutomotiveDysfunction Ty!

[@scottgarvy]

I got it done. I didn't have a torque wrench that goes that low. Had to do it by feel.

[@DallasKings214]

71ft lbs

[@punishrs]

I’m getting code p0171 dealer saying cam shaft cover…

[@AutomotiveDysfunction]

Could be couple things like : evap emission purge solenoid valance ,pcv,check for vacum leaks ..
Check air cleaner for outlet duct for splits
Check vacum , air leaks
Verify good fuel quality and proper pressure
Clean MAF sensor (with breaks clean and dry/blow off right away with air

[@AutomotiveDysfunction]

Yes it could be … get new camshaft cover with new gasket

[@punishrs]

Could this cause a p0171 code?

[@lilsavagegod]

yes

[@wmuchmore]

Most likely the diaphragm on the upper right hand side of the cover.

[@quamcalvin7471]

Mines has the same code also stablitrack light comes on and off

[@heathnunley502]

What’s the torque spec mf?!? Jesus

[@AutomotiveDysfunction]

8NM (71 LB In)