How to make 12 volt Police flasher
Вставка
- Опубліковано 5 вер 2024
- COMPONENTS
1)BC 547 X2
2)180 ohm X2
3)10 uf capacitor X2
4)100K X2
5)12 volt led X2
This circuit is an Astable Multivibrator or we can say Free Running Multivibrator, which has no stable states. Its output oscillates continuously between its two unstable states without the aid of external triggering. The time period of each states are determined by Resistor Capacitor ( RC ) time constant.
click here for circuit diagram :-
drive.google.c...
Also watch Police flasher with 12 modes :-
• How to make Police Fla...
Thanks for watching
Thanks bro for this video
Great video 👌👌👌👍🏼👍🏼👍🏼👏
Very good jobe
Good video I like your project
Merci pour cette belle réalisation
Thank you very much. Only a question: How can I make it work with a electric car system? When engine is off the circuit are 12VDC, but when engine runs voltage is between 13,8 - 14,8 VDC. I think is so higher and at least, leds burns. If I try with a L7812 is OK when engine's on, but so low voltage when motor stops.
Can you help me?
Excuse my poor english. Thank again. Best wishes.
No need of additional circuit, you can directly use it.
@@hobbyproject at now I've
Sorry. At now I've used 12vdc leds directly, without flash circuit and, sooner por later, all of leds burns. That's because I've said it. Model what I use ia 12vdc orange x6 leds, and I want to use for lateral signalization.
@@luisclares4066 you could have used a potentiometer for both the leds
അടിപൊളി വീഡിയോ പൊളിച്ചു മുത്തേ
Good
Please try to add audio description in your videos.good going 👌
Will do.... 👍👍
Bro i made it but the lights are not blinking what to do??
Me too bro not blinking
Which other resistors to use instead of 180 ohm?
I'm looking at first-time electronic items. Good luck with the event. One drawback is Led Light and Burned Late. What needs to be changed to change speed
By adjusting the value of capacitor
@@hobbyproject Then what type of capacitor should be added
Bagus pak
Plz tell me how to connect wire
Here again. I've looked for the led's datasheet what I use, and it runs in 150 - 180 mA every. It's too much for this circuit? What transistor can I use instead?
Tank you again, for your patience.
please trying to make audio n slowly with wiring connection of back side board ?
How to more fast light are flashed how plz tell me than it
Bhai aisa btao ki jisse 1 baar ki jagah 2 baar jale isi pattern me
Capisitar कौनसा use किया है भाई plzz tell me
new subscriber
💯💯👍👊
How to run it with USB point like for installation in car can any fix to to make this circuit that run with USB Please 🙏🙏
Bhai 180 ohm resister nhi mil rha h uske jagha me kaunsa resister laga sakte h plz reply bhai
150 ohm can be used
@@hobbyproject thanks bhaiya ji
👍👍👍
Bro thanku very much it's working .....
12 v bulb illama chinna led5 bulb use pannalama intha procedure la
Yes
Nice video Bro 🙏🙏🙏🙏
Does it works in bike indicator
Yes
So nice bro it's cool. Keep it up bro.. Achcha laga me v karoonga apne fat tyre bicycle me.
If 180 their resistance is not found then which resistance to use please help me
You can use 220 ohm .
How to connect this in car wiring will u explain me please?
So you want to caught where anyone can see you on a comment asking how to do something that is a misdemeanor
How to operate it on 3.7 volt?
Can you tell me the background music
Sorry . i forgot its name
Great job 👏
Can you deliver me this complete product?
I have referred your video to make the light for my other project...giving credits to you and sharing your video link in my project...see my project on my channel...thanks for the video
plz audio , or next time video ki fast mat karo
How much ampear current it requires?
Woow this is col
Can we build this for only one 12v led light strip ..Like bicycle flasher
Yes
@@hobbyproject pls share how and components needed...If possible cost also.
Check the description
How can we make it for single led. I need details for that
ua-cam.com/video/hSGJoNMupbk/v-deo.html
See this video
How to speed up a flasher?
Increase the value of capacitor
Bro i made this ckt but LEDs are not flashing LEDs remains ON only
Whats the fault??
Check transistor/capacitor pin or it may be due to dry soldering
Okay
My 100k resistor showing 75k value
Laykin Bhai Jan muja diagram ki samhaj nai a ri k solding kis tarah kerni hai .... Please reply me.
Use breadboard
@@hobbyproject
Bhai Jan Jo ap nay solding ki wo method bata saktay hien muja please.
Please refer circuit diagram. if you still have doubts mail me on
jishnumaleparambil@gmail.com
можешь написать мне название всех деталей для этого чуда
Can we Use 9V Duracell or any other Cell please reply
Yes.
@@hobbyproject so how can connect it
@@hobbyproject It Means I want to Make it usb led can any fix
Bro flesher back side kisko kisko kisky shat wire atached karna ha tell bro
Send your number pls
Can i connect my Honda aviator scooter
Yes
Bhai pcb ke piche ki pic mujhe send karo
Nam Kya hai is flasher ka
Bhai good video.
Thank you for your valuable support
Can i use bc 548
Yes .both transistor are ~same
Bro 180 ohms ke jaga dosra value konsa lagana he hamare han yahan par 180 ohms ka resistor nahi mil rahaa
You can use any value b/w 150 to 200 ohm
@@hobbyproject ok thank you bro
@@hobbyproject same istarah Kam karega Jo bi value use kron to
Can we use any other resister on 180ohm tell me bro
Any value b/w 150 to 220 ohm
Muje aap ye banakar de sakte ho?please replay karo jaldi please jaldi please please please
Bro please circuit board back side tell me bro
Circuit link given in description
Bro it doesn't work when I connect to power supply the side only blink
Ellam kodth connection full kodth but only one bulb Kathi nilkunnu not blinking
Check transistor connections or polarity of the capacitor
@@hobbyproject OK Nokatt
It's working 😍
Can I use the Capistar 10v?
No. Minimum 16 volt required
भाई जब मैने 180 ohm ki jagah 100 ohm ka resister use Kiya to light flesher nhi hua why
Give me it's solution
Bro
100 ohm use kiya tho be circuit work hone chahiyee
Nice
I also made a police light
👍
I have BC546?
BC 546, 547, 548 are almost same
@@hobbyproject Thank you for this content
@@hobbyproject I have 120k ohms ?
No problem. Use R2,R3 same value
Pregumta 9V o12V entrada
Chetta 40 ruppa tharam enniku oranam undaki tharumooo😜😜
Sure
9 volt il work avumo ??
Yes.
I'm not a engineer but me apni cycle me boht kuch laga leta hu
drive.google.com/file/d/11FfyVDF5aczr5qytrfvvZLw89X16nrpa/view
@@hobbyproject are Bhai uSki photo hi bhej do
@@hobbyproject mujhe samajh nai aa raha hai
Snd me your whats app number. So that i can help you to build this
@@hobbyproject thanks bro
Bhai mere liye ye light banado me apko hi 100₹ dedubga
🌹🌹👉
അമ്പട
Just attach it in front of your fat bike , devil it looks ..😈😈
👌👌🖐🖐👎👎👎👎👎👎👎
Capisitar कौनसा use किया है भाई plzz tell me
10 uf 25v capacitor
@@hobbyproject please bhai