ilk önce teşekkürler. harika iş oldu. onlarca video izledim hepsinde 100k direnç yanına paralel kısa devre yapmak anlatıldı ancak c410w modelde kart direkt kapattı kendini. sizin teknikte ölçtüğünüz 58ohm lük direnç püf nokta. bende 76ohm lük direnci 100k lik dirence paralel bağladım sonra yazıcıyı açtım yine kırmızı hatada kaldı. kapattım ve 76ohm luk direnci ayırıp orijinal halinde çalıştırdım ve normale döndü %100 oldu. faydalı olan tek video için teşekkürler.
Hi the wedge shape at the front will also need to be cleaned out of toner, it also stores it in there after it’s wiped off the drum. Requires a bit of disassembly on the sides and then there’s a couple tabs at the bottom. After removal you should empty it, then do the reset. Also be a bit more careful than the poster with the drum, they’re quite delicate even wiping it with a paper towel can scratch and ruin it, if there’s any dust on the towel.
Oh my, painful to see the drum being scratched and possibly ruined by just putting the drum unit upside down on those metal contacts :( Otherwise, great tutorial to save money, thanks!
Great stuff - Samsung hang you head in shame. I really appreciate you taking the time to produce these videos and sharing them with us. Keep up the good work mate.
Hello everyone! I'm having an issue with my Samsung color laser printer. I recently replaced two resistance fuses in the printer's oven, both with a resistance value of 100 ohms and connected in parallel. However, the fuses keep burning out and the printer indicator switches from blue to orange. Has anyone experienced this problem before or have any ideas on what might be causing this? I would greatly appreciate any advice or suggestions. Thank you!
I've done the same with the Okidata printer as well, they use a fusible link for the tray and all i did was put a low value resistor and left it attached after it thought it had a new tray. only difference I used was a metal film 1/8 watt resistor PS NEVER buy a laser pronter from Brother the color is TERRIBLE looks like a flat color and I now miss my Okidata that printed beautiful color prints this brother is a hunk of junk that cost 500, should have kept looking for a fuser for the Okidata instead of buying this crap machine, thought I would be getting a better print not 100 times worse
Hello everyone! I'm having an issue with my Samsung color laser printer. I recently replaced two resistance fuses in the printer's oven, both with a resistance value of 100 ohms and connected in parallel. However, the fuses keep burning out and the printer indicator switches from blue to orange. Has anyone experienced this problem before or have any ideas on what might be causing this? I would greatly appreciate any advice or suggestions. Thank you!
ilk önce teşekkürler. harika iş oldu. onlarca video izledim hepsinde 100k direnç yanına paralel kısa devre yapmak anlatıldı ancak c410w modelde kart direkt kapattı kendini. sizin teknikte ölçtüğünüz 58ohm lük direnç püf nokta. bende 76ohm lük direnci 100k lik dirence paralel bağladım sonra yazıcıyı açtım yine kırmızı hatada kaldı. kapattım ve 76ohm luk direnci ayırıp orijinal halinde çalıştırdım ve normale döndü %100 oldu. faydalı olan tek video için teşekkürler.
Well done! Good to see someone outsmarting the obsolescence :)
Hi the wedge shape at the front will also need to be cleaned out of toner, it also stores it in there after it’s wiped off the drum. Requires a bit of disassembly on the sides and then there’s a couple tabs at the bottom. After removal you should empty it, then do the reset. Also be a bit more careful than the poster with the drum, they’re quite delicate even wiping it with a paper towel can scratch and ruin it, if there’s any dust on the towel.
An 8 kilowatt watt resistor in such a small package! Wow :)
Very useful tip this thanks for sharing!
a small copper thread would also do the trick
Explained so well! Fantastic thanks so much.
Oh my, painful to see the drum being scratched and possibly ruined by just putting the drum unit upside down on those metal contacts :( Otherwise, great tutorial to save money, thanks!
Very, very good.
Great stuff - Samsung hang you head in shame. I really appreciate you taking the time to produce these videos and sharing them with us. Keep up the good work mate.
Hello everyone! I'm having an issue with my Samsung color laser printer. I recently replaced two resistance fuses in the printer's oven, both with a resistance value of 100 ohms and connected in parallel. However, the fuses keep burning out and the printer indicator switches from blue to orange. Has anyone experienced this problem before or have any ideas on what might be causing this? I would greatly appreciate any advice or suggestions. Thank you!
clp 325 reset ?
I've done the same with the Okidata printer as well, they use a fusible link for the tray and all i did was put a low value resistor and left it attached after it thought it had a new tray. only difference I used was a metal film 1/8 watt resistor
PS NEVER buy a laser pronter from Brother the color is TERRIBLE looks like a flat color and I now miss my Okidata that printed beautiful color prints this brother is a hunk of junk that cost 500, should have kept looking for a fuser for the Okidata instead of buying this crap machine, thought I would be getting a better print not 100 times worse
Hello everyone! I'm having an issue with my Samsung color laser printer. I recently replaced two resistance fuses in the printer's oven, both with a resistance value of 100 ohms and connected in parallel. However, the fuses keep burning out and the printer indicator switches from blue to orange. Has anyone experienced this problem before or have any ideas on what might be causing this? I would greatly appreciate any advice or suggestions. Thank you!