agradezco su tiempo en ayudarme con un reemplazo del sensor Hall de mi moto que tiene REF: H-413F consigo en mi ciudad la RF: 41F lo podre utilizar gracias
first you know the voltage and current rating of led then simply use [R = V/I] to get right value of resistor. For example if your led is Red 5mm then R = 1.8/0.01 so resistor should be around 180E thats it....
Sir my access125 converted electric scooter 67v 800w hub motor But recently hall sensor defective sir N41 909 This hall sensor not available in market so any alternative is suitable Give me replay sir thankq
Does anyone know the sensing bandwidth of the A3144, I would like to use it as a tach for a bldc motor, which is 920 kv running at 12V and has 14 permanent magnets, as such it should pulse around 2.5 kHz. Can this little guy move that fast lol
I am using this hall sensor with an N channel Mosfter IRFZ44N to run a make shift pulse motor. I am connecting the hall's output to the gate of the FET and also with 1K resistor to the supply.] It works. But when the magnet passes the hall, the FET turns off. How can this hall be wired so the FET turns on when the magnet passes by it? Wiring this with an NPN mosfet, its ouput causes the FET to go off when the magnet passes by with the way I have it. I like the opposite to happen if that is possble.
When you passes magnet A3144 sensor give negative output (if you want to turn on mosfet when magnet passes through A3144 sensor) so you need to use connect the output of A3144 to PNP BJT like BC557 then connect MOSFET gate with 10K pull-up with GND.
@@innovationic The hall output to gate of BC557 and then connect the gate of a PFET to where besides it's gate to the 10K pull up ( or pull down) to the ground?
I need to connect the PFET to the BJT also. Is this correct otherwise they have no relationship between the two, beside the resistor to the ground ( which its drain also the drain of FET goes to). So do I hook up the gate of the PFET to the emiiter, the collector, the base of the BJT unless there is something else here I am missing? And does the 10K resistor connects to the ground or does it really connect to the +VDD where the source of the PFET goes to?
Hy, i have a question, can you tell me how can i connect a loudspeaker to a hall sensor in order to be able to control volume. The loudspeaker have digital volume control. Thank you in advance for your answer
@@innovationic thank you for your quick answer. Yes, i want to control loudspeaker digital volume with Kick Scooter TF-100 Display hall sensor. Can i connect directly to the 3 pins of the hall sensor ? or should i connect on the board?
I try hall sensor 41F but not working on 3v lithium battery? Only 5v work on hall sensor 41F. How it will work on 3v battery? Hope you can help me thanks.
See datasheet given below www.google.com/url?sa=t&source=web&rct=j&url=in.element14.com/honeywell/ss41/sensor-hall-effect-sink-4-5-24v/dp/1470593&ved=2ahUKEwjQs-6Z9pf1AhUFjeYKHQ9cBN0QFnoECCwQAQ&usg=AOvVaw1o9SRLjtJ1IDZ-upFwDXV2
This is the best video about hall sensors. No nonsense.
Lage rho....achhi video hai...👌👌
Why does the watcher have to put up with the music? I refuse to listen.
I think people watching videos with music makes them to feel better. Otherwise music or audio depends upon type of video.
@@innovationic yep but tbh the music is too loud.
Thanks for your comment
In upcoming videos I do my best
Then turn down the volume😂😂😂@@Zero-oh6ek
Excelente 👌 explicación
thankyou
agradezco su tiempo en ayudarme con un reemplazo del sensor Hall de mi moto que tiene REF: H-413F consigo en mi ciudad la RF: 41F lo podre utilizar gracias
most welcome
How to choose what resistor you need for leds for example and how to make sure it doesn't block too much current?
first you know the voltage and current rating of led then simply use [R = V/I] to get right value of resistor.
For example if your led is Red 5mm then
R = 1.8/0.01
so resistor should be around 180E thats it....
Sir my access125 converted electric scooter 67v 800w hub motor
But recently hall sensor defective sir
N41 909 This hall sensor not available in market so any alternative is suitable
Give me replay sir thankq
Generally hub motors have same sensor you can go for A3144 or any 3 pin Hall sensor
Good work
Thank u 😊
Does anyone know the sensing bandwidth of the A3144, I would like to use it as a tach for a bldc motor, which is 920 kv running at 12V and has 14 permanent magnets, as such it should pulse around 2.5 kHz. Can this little guy move that fast lol
this can handle upto 10KHz pulses and with proper driver circuit a3144 can rotate fast enough speed
good choice for A314 , bad one for the music
thankyou for watching
I am using this hall sensor with an N channel Mosfter IRFZ44N to run a make shift pulse motor.
I am connecting the hall's output to the gate of the FET and also with 1K resistor to the supply.]
It works. But when the magnet passes the hall, the FET turns off.
How can this hall be wired so the FET turns on when the magnet passes by it?
Wiring this with an NPN mosfet, its ouput causes the FET to go off when the magnet passes by with the way I have it. I like the opposite to happen if that is possble.
When you passes magnet A3144 sensor give negative output (if you want to turn on mosfet when magnet passes through A3144 sensor) so you need to use connect the output of A3144 to PNP BJT like BC557 then connect MOSFET gate with 10K pull-up with GND.
@@innovationic The hall output to gate of BC557 and then connect the gate of a PFET to where besides it's gate to the 10K pull up ( or pull down) to the ground?
Sorry it's pull down 10k resistor to GND
I need to connect the PFET to the BJT also. Is this correct otherwise they have no relationship between the two, beside the resistor to the ground ( which its drain also the drain of FET goes to). So do I hook up the gate of the PFET to the emiiter, the collector, the base of the BJT unless there is something else here I am missing?
And does the 10K resistor connects to the ground or does it really connect to the +VDD where the source of the PFET goes to?
Wait I make video in few minutes
3.3v alternative? thanks!
I have tested that A3144 works from minimum 2.78v and at 3.3v it works pretty well
@@innovationic great thanks!
Hy, i have a question, can you tell me how can i connect a loudspeaker to a hall sensor in order to be able to control volume. The loudspeaker have digital volume control. Thank you in advance for your answer
you mean to control volume using hall sensor via magnet
@@innovationic thank you for your quick answer. Yes, i want to control loudspeaker digital volume with Kick Scooter TF-100 Display hall sensor. Can i connect directly to the 3 pins of the hall sensor ? or should i connect on the board?
digital volume control in your loudspeaker the volume nob is potentiometer or rotary encoder
according to your system the hall sensor would connected
Resistor Value ?
120Ω resistor
Where can I get hall sensors
Thanks for comment
You can take from bldc motor or repairing shop or you can buy online
Hello is this work also on 3v lithium battery?
I try hall sensor 41F but not working on 3v lithium battery? Only 5v work on hall sensor 41F. How it will work on 3v battery? Hope you can help me thanks.
Only like no reply? 😂
It requires atleast 4.5v
See datasheet given below
www.google.com/url?sa=t&source=web&rct=j&url=in.element14.com/honeywell/ss41/sensor-hall-effect-sink-4-5-24v/dp/1470593&ved=2ahUKEwjQs-6Z9pf1AhUFjeYKHQ9cBN0QFnoECCwQAQ&usg=AOvVaw1o9SRLjtJ1IDZ-upFwDXV2
Thanks.. But other hall sensor like 3144 work on 3v lithium battery. Is there a way to use 41F using 3v?
होल सेंसर अगर मंगवाना चाहे कैसे मंगवा सकते है
Amazon par mil jayega ya apke local electronics store me mil jayega
So sensor output seems negative... in relation to positive common.
yes its output is negative so you can use PNP transistor to get positive signal
@@innovationic No, I don't want to. Just will ask Arduino to look for low signal )
just use pullup resistor to your Arduino input or use opamp to get desired output(either +ve or -ve)
Bhache log bejao taali
👏
noisy
Thanks for comment 😊 I make more interesting and better videos in future🙂