I was skeptical of the small bezels. But seeing how easy it was to replace the screen without taking everything out from the back first, is truly marvelous. Great design by Samsung.
lol yeah. Thanks! The screen ran me $240 and the adhesives $50 since I had them shipped from overseas as they were not available here yet. But adhesives should run closer to $20-25 once they are more widely available.
@@PBKreviews It doesnt always, i was told they have a machine at samsung services to measure the water resistance. Technician told me youd surprised how many times they fail the test and they'd have to start over. It would be better for adhesion purposes if you had used some ISO at least on the frame prior to installing screen and back glass.. This is better done with gloves too, i always use gloves when working on phones. Once you get the hang of it you cant go back to pure fingers greasy assembly. No more smudgeish greaseish fingerprints anywhere, especially so for the glue's adhesion surface or the glue itself, where there shouldn't be. Just noted a few suggestions. Anyway as always, great video! Thumbs up!
I had my screen replaced under warranty and only now I discovered that the rear panel needs to be removed for this service. Then I checked my rear panel and one side is slightly outwards. I pressed a little bit with my fingers and it seems to be flush with the frame now. My main concerns are water resistance and also make sure the panel will stay flush with the frame as it should. Do you recommend I use a hair dryer to heat it and then use some clamps for a few minutes? Or should I ask the repair center to redo the fixing?
ask them to re apply the back cover. heat will only loosen it and not help. They probably didn't apply it properly or clean off the original adhesive residue before applying the new one.
@@PBKreviews Thanks, it seems exactly what you mentioned. When I press the back cover it becomes flush with the frame but after a short time it goes back outwards. It is very, very minimal but it bothers me.
Brilliant work chief !!! Looking at everything in detail would i be righ if i said the when people drop they phones and break they screen, its actuality front glass borkem only or does the actual aluminium sheet underneath gets damaged as well ? Just out of pure curiously. Thanks again i value your professionalism the most !!!!🙌
Thanks. Yes, as long as you properly remove the old adhesive, and re apply the original pre cut adhesive/rework kit made for the phone properly, it will retain the water and dust resistance.
1. Проклейку, после установки на корпус, нужно прогреть феном или нижним нагревателем для её "активации". Иначе, приклеится плохо и со временем, дисплей и крышка задняя, будут отклеиваться. 2. После этого, нужно телефон положить под пресс или зажать специальными прищепками на какое-то время.
I do put it with clamps after. Also the heat loosens the adhesive. From what I've been told from a Samsung Tech at the US repair team, they actually put the adhesives in a freezer to keep them more sticky. Then when installing the adhesives, they hold stronger.
i have an s24 plus does the screen have a color like the phone itself i sent mine in for a screen replacement but they say the only have violet and yellow?
Have you heard of the grainy/banding displays problems that are affecting some batches of s24 Ultra? Could replacing the screen as you did be a solution to that issue? I'm very worried since I have the issue, and read that people that requested a replacement got the whole phone replaced... with another faulty one.
@@PBKreviews I'm fairly convinced it's related to the display (to the individual pixels). Also, if it was a software problem I think it should affect all units, but as far as I've read around, many people claim theirs are perfectly fine.
Technically, you can remove just the screen without disassembling the rest, but applying a new screen is more difficult since once you apply new adhesive, you have on chance at applying the screen perfectly to the frame while aligning the screen connector to the cable so it snaps on when you apply the screen. If you don't get a good connection or the cable doesn't connect, you will have to pry the screen off again which poses a high chance of damaging the screen. So best way is to remove the back, and the bottom speaker assembly so you can disconnect the flex cable for the screen, then remove the screen, apply the new one and reconnect the flex cable from the back. Then re assemble the back cover etc. If you are referring to the process of removing the old adhesive, and applying the new ones, if you want to maintain the water resistance and dust resistance, then yeah you need to properly apply the adhesive made for the phone to be safe on that end.
Thanks you for video. Can you please send direct link for screen replacement, everything you used in this video? I got lost in link in descriptions to many items in that website, I don't know how to look for & don't want to order wrong thing. I need to replace Screen going to cost me $550 here after your video I want to try to replace myself.
You can get it from www.mobilesentrix.com/replacement-parts/samsung/galaxy-s-series/galaxy-s24-ultra-5g or rounded.com/galaxy-s24-ultra-sm-s928b/ . It's easier if you get the screen with frame combo, since all you have to do is move over your motherboard and parts to the new screen with frame and not worry about attaching the screen to the frame. Rounded.com link has the combo in stock but a bit more pricey. If you are getting the screen without the frame, make sure to get the adhesive for the screen/lcd which is sold separately.
It's not too difficult. If it's not prying off enough to put a pry tool in between the frame and back glass with the suction cup, you need to apply more heat. Once its hot enough should peel off easier.
The coating on my screen looks to be peeling in one area after 3 months, I've contacted Samsung and booked a repair, I'm still covered by warranty, but worse case scenario can only the front glass be replaced?
When you have applied the new screen i sow a lego type connector on the bottom of the screen I didn’t hear a clicking sound when you applied the screen why
I replaced my s24 ultra screen today, I told the technician to install the new screen. Thank God the screen worked well and without any defect, I only noticed one problem, the S pen stopped working, a message appears saying that the s pen is not compatible with the screen ... It does not let you write or do any air commands with the pen. The S pen is very important to me and I use it a lot, I do not know what to do now😢😢😢... my S24 Ultra is the Global black version and i replaced the screen with the one that comes with the frame..... do you know what should it be?
Oh boy, I wish I could get my hands on some original spare parts and kits like you did right here. It’s so bad we have to put up with third party crap over here, they can’t even come close to the original quality!
I really do prefer a suction-heating machine to remove a screen. It's easier and safer than heatpad or hairdryer. I've already removed a lot of screens without damaging it by doing like that.
There is, but its much more hard to find the complete screen with frame assembly even though it is available because samsung is now doing screen only replacements vs the frame combo (I assume because of the higher cost of the titanium frame). So more people will be doing a screen only replacement vs screen with frame combo on the S24 ultra.
Hi, there is, its just the first thin layer which is glued to the glass peels off easily when heated from the screen so stays attached to the glass. That's why the glass looks dark in color, or else the glass is clear. If you look at parts of the glass where that thin layer got peeled off you will see its clear. But yeah that's what I thought at first until I looked closer and saw there is a thin layer glued to the glass which just peels off from the screen when prying it off.
@@PBKreviews but after getting flat panel we are not able to replace only glass in case we broke it that's how they done intentionally. And ultimately display quality is just downgraded 😢
Why did Samsung do this. After keeping their screen replacement almost identical from Samsung s20 to s23 ultra, they finally changed the internal design,😢
Yup, there is still screen and frame combos, but its much harder to find since samsung is mainly doing screen only repairs now on the 24 ultra (I assume due to increased cost of the titanium frame).
In this newer model, they mainly sell the screen itself now due to the titanium frame. However they do sell the combo also just harder to find since they do screen only replacements primarily for this model.
I have looked into it, but there are already a few teardowns of it on UA-cam and I usually don't get enough views on the sony phones to justify purchasing the device. So currently I don't have any plans to do that model but may look into doing the VI when it releases.
I have looked into it, but there are already a few teardowns of it on UA-cam and I usually don't get enough views on the sony phones to justify purchasing the device. So currently I don't have any plans to do that model but may look into doing the VI when it releases.
Why no Exynos for the S24 Ultra????? Why only Spandragon for this? BECAUSE SAMSUNG KNOWS THEUR EXYNOS IS INFERIOR TO SNAPDRAGON, THATS WHY THEY DIDN'T TAKE CHANCES THE THWIR FLAGSHIP........
yup, most phones will have the copper film behind the screen to transfer heat. In addition to that, there is the vapor chamber (which not all phones will have) and graphite film.
Excellent! You are really professional and precise in removing every single bit of adhesive. 👍
Thank you very much! 👍
@@PBKreviews БРАТ СКОЛЬ СТОИТ ЗАМЕНА ЭКРАНА ? ? ?? ? КАКАЯ ЦЕНА ? ? ?
I was skeptical of the small bezels. But seeing how easy it was to replace the screen without taking everything out from the back first, is truly marvelous. Great design by Samsung.
Marvel of using a flat display now.
@zerotwo_.002 which is better than a curved screens
LEGO for people with a huge amount of patience and nerves of steel :D
Well done mate, just by curiosity: how much have to spent on the parts?
lol yeah. Thanks! The screen ran me $240 and the adhesives $50 since I had them shipped from overseas as they were not available here yet. But adhesives should run closer to $20-25 once they are more widely available.
@@PBKreviews Awesome, thanks for the detailed info :)
You're welcome
Did you used clamps after for the adezive to seal off better ?!
Awesome and clean video but how did You prevent dust from entering on the camera optics?
Good thing there is no part pairing😂😂😂😂
lol yup
Only on apple products because they are greedy capitalists
PPBKreviews Bro is the S24 70% automation assembly?
Seeing that adhesive tool first time looked like magic lol
lol yeah, it's a life saver vs doing it by hand.
Whats the name of the parts on rounded that you ordered, it's hard to understand that website and they don't really have pics of the parts.
check mobilesentrix.com to see if they have them.
Hey do you think it still has its water resistance after that ?
as long as the adhesive is installed properly, yes should retain water resistance
@@PBKreviews It doesnt always, i was told they have a machine at samsung services to measure the water resistance. Technician told me youd surprised how many times they fail the test and they'd have to start over. It would be better for adhesion purposes if you had used some ISO at least on the frame prior to installing screen and back glass.. This is better done with gloves too, i always use gloves when working on phones. Once you get the hang of it you cant go back to pure fingers greasy assembly. No more smudgeish greaseish fingerprints anywhere, especially so for the glue's adhesion surface or the glue itself, where there shouldn't be. Just noted a few suggestions. Anyway as always, great video! Thumbs up!
I had my screen replaced under warranty and only now I discovered that the rear panel needs to be removed for this service. Then I checked my rear panel and one side is slightly outwards. I pressed a little bit with my fingers and it seems to be flush with the frame now. My main concerns are water resistance and also make sure the panel will stay flush with the frame as it should. Do you recommend I use a hair dryer to heat it and then use some clamps for a few minutes? Or should I ask the repair center to redo the fixing?
ask them to re apply the back cover. heat will only loosen it and not help. They probably didn't apply it properly or clean off the original adhesive residue before applying the new one.
@@PBKreviews Thanks, it seems exactly what you mentioned. When I press the back cover it becomes flush with the frame but after a short time it goes back outwards. It is very, very minimal but it bothers me.
Brilliant work chief !!! Looking at everything in detail would i be righ if i said the when people drop they phones and break they screen, its actuality front glass borkem only or does the actual aluminium sheet underneath gets damaged as well ? Just out of pure curiously. Thanks again i value your professionalism the most !!!!🙌
Good video. I only have one doubt. After doing that, does it still maintain protection against water and dust?
Thanks. Yes, as long as you properly remove the old adhesive, and re apply the original pre cut adhesive/rework kit made for the phone properly, it will retain the water and dust resistance.
I think 50%😅
Good update keep it up the good work 👍👍👍
👍 Thanks!
On the parts website for the screen it says it is LCD. Is it not the original screen since the screen is OLED?
Sorry if this is a dumb question.
Is the replacement part original or not ?
And does the fingerprint still work after screen replacement ?
yes original and yes fingerprint sensor works. You may need to factory reset the phone if you have any issues with the sensor not registering
1. Проклейку, после установки на корпус, нужно прогреть феном или нижним нагревателем для её "активации". Иначе, приклеится плохо и со временем, дисплей и крышка задняя, будут отклеиваться.
2. После этого, нужно телефон положить под пресс или зажать специальными прищепками на какое-то время.
I do put it with clamps after. Also the heat loosens the adhesive. From what I've been told from a Samsung Tech at the US repair team, they actually put the adhesives in a freezer to keep them more sticky. Then when installing the adhesives, they hold stronger.
#clean #design by #samsung ❤ finally 🎉
Masterful work once again !
Thanks!
@@PBKreviews БРАТ СКОЛЬ СТОИТ ЗАМЕНА ЭКРАНА ? ? ?? ? КАКАЯ ЦЕНА ? ? ?
Good work, you always inspire me!
Thank you
How much it cost for LCD repairing? Pls
i have an s24 plus does the screen have a color like the phone itself i sent mine in for a screen replacement but they say the only have violet and yellow?
One Inportant step I think we should check if the screen works or not before putting it on the frame :)
Yeah, should always be checked first. I know I checked it but should have mentioned it as well.
I'm curious, Do the phone keeps the water resistence after replace the water LCD screen?
Amazing video. Keep up the good content! 😎
Thanks!
Thanks for doing these!
You're welcome :)
Have you heard of the grainy/banding displays problems that are affecting some batches of s24 Ultra?
Could replacing the screen as you did be a solution to that issue?
I'm very worried since I have the issue, and read that people that requested a replacement got the whole phone replaced... with another faulty one.
hmm I'm not too sure, since it could be a screen issue but can also be an issue with software or the gpu on the phone.
@@PBKreviews I'm fairly convinced it's related to the display (to the individual pixels).
Also, if it was a software problem I think it should affect all units, but as far as I've read around, many people claim theirs are perfectly fine.
always nice and informative 💪❤
Thanks!
Do i have to go through the whole process just to change out the screen?
Technically, you can remove just the screen without disassembling the rest, but applying a new screen is more difficult since once you apply new adhesive, you have on chance at applying the screen perfectly to the frame while aligning the screen connector to the cable so it snaps on when you apply the screen. If you don't get a good connection or the cable doesn't connect, you will have to pry the screen off again which poses a high chance of damaging the screen. So best way is to remove the back, and the bottom speaker assembly so you can disconnect the flex cable for the screen, then remove the screen, apply the new one and reconnect the flex cable from the back. Then re assemble the back cover etc. If you are referring to the process of removing the old adhesive, and applying the new ones, if you want to maintain the water resistance and dust resistance, then yeah you need to properly apply the adhesive made for the phone to be safe on that end.
Thanks you for video.
Can you please send direct link for screen replacement, everything you used in this video?
I got lost in link in descriptions to many items in that website, I don't know how to look for & don't want to order wrong thing.
I need to replace Screen going to cost me $550 here after your video I want to try to replace myself.
Autocorrect in descriptions.
You can get it from www.mobilesentrix.com/replacement-parts/samsung/galaxy-s-series/galaxy-s24-ultra-5g or rounded.com/galaxy-s24-ultra-sm-s928b/ . It's easier if you get the screen with frame combo, since all you have to do is move over your motherboard and parts to the new screen with frame and not worry about attaching the screen to the frame. Rounded.com link has the combo in stock but a bit more pricey. If you are getting the screen without the frame, make sure to get the adhesive for the screen/lcd which is sold separately.
Is loosening up that back glass adhesive and removing the glass itself really that easy?
It's not too difficult. If it's not prying off enough to put a pry tool in between the frame and back glass with the suction cup, you need to apply more heat. Once its hot enough should peel off easier.
great design from Samsung and thank for tutorial.
you're welcome
Wooooow...amazin job, SUBSCRIBED!
Thanks!
Wow! Nice to see your video. 😊
👍
Is going to be waterproof after repair
The coating on my screen looks to be peeling in one area after 3 months, I've contacted Samsung and booked a repair, I'm still covered by warranty, but worse case scenario can only the front glass be replaced?
Nope, requires special tools and machines to get it done.
Very helpful and well explained. Will keep in mind to fix my own phone if I brake it
👍 thanks
When you have applied the new screen i sow a lego type connector on the bottom of the screen I didn’t hear a clicking sound when you applied the screen why
I replaced my s24 ultra screen today, I told the technician to install the new screen. Thank God the screen worked well and without any defect, I only noticed one problem, the S pen stopped working, a message appears saying that the s pen is not compatible with the screen ... It does not let you write or do any air commands with the pen. The S pen is very important to me and I use it a lot, I do not know what to do now😢😢😢... my S24 Ultra is the Global black version and i replaced the screen with the one that comes with the frame..... do you know what should it be?
Might have to check the spen connection inside the phone
Now after this will the phone retain its IP rating?
Oh boy, I wish I could get my hands on some original spare parts and kits like you did right here. It’s so bad we have to put up with third party crap over here, they can’t even come close to the original quality!
check out rounded.com or mobilesentrix.com both carry original replacement parts and ship international just in case you need parts.
So good mr miss you from Iraq🎉...
Thank you 👍
Too good 👍
Would be nice to see if it holds its water resistance
Wow bro amazing fiting done
👍
I really do prefer a suction-heating machine to remove a screen. It's easier and safer than heatpad or hairdryer. I've already removed a lot of screens without damaging it by doing like that.
👍
Doesnt it void your warranty? Too risky for me to do
well if your screen is broken, your warranty is void. But yep, not for everyone to do.
What is the screen price for the s24 ultra?
I paid $240
Is that direct from Samsung, or 3rd party? @@PBKreviews
What's the Link or Web Site to order a replacement screen for the Samsung 24s Ultra?
Thank you
Master class
👍
So no more display repair with frame?
There is, but its much more hard to find the complete screen with frame assembly even though it is available because samsung is now doing screen only replacements vs the frame combo (I assume because of the higher cost of the titanium frame). So more people will be doing a screen only replacement vs screen with frame combo on the S24 ultra.
Please teardown the new one of samsung a55 5g and a34 5g. Thank you
Will do hopefully in a week
@UC20o1OUWGrixnCEE1gQ9 I will buy one of them after seeing your video.
Thank you
Very impressive. Almost makes me think I can do it. Almost.
👍
any idea why my S pen isn't working after screen change
БРАТ СКОЛЬ СТОИТ ЗАМЕНА ЭКРАНА ? ? ?? ? КАКАЯ ЦЕНА ? ? ?
You must test lcd before you reassemble
Team Samsung Galaxy S24 ultra ❤
👍
Samsung 👑 🏅 🎉😮
Tq!
Welcome
Can you still use the phone without the glass???
I miss the days of getting an OCTA for repairs.
yep :)
Even the service center people don't clean it this much.
👍
After samsung S7, the ony S series phone in which no need of housing replacement
Mai kal hi liye ye phone 🎉🎉🎉🎉 150000 pada🎉🎉🎉❤❤❤❤
Nice
👍
Display is so wired there is no adhesive between display and glass poor build quality
Hi, there is, its just the first thin layer which is glued to the glass peels off easily when heated from the screen so stays attached to the glass. That's why the glass looks dark in color, or else the glass is clear. If you look at parts of the glass where that thin layer got peeled off you will see its clear. But yeah that's what I thought at first until I looked closer and saw there is a thin layer glued to the glass which just peels off from the screen when prying it off.
Это матрица так расслаивается на две части.
Самая верхняя её часть, остаётся на стекле.
У Самсунга все Soft OLED дисплеи, сделаны так.
@@PBKreviews but after getting flat panel we are not able to replace only glass in case we broke it that's how they done intentionally. And ultimately display quality is just downgraded 😢
yup
Display how pixel glass seperate
not sure what you mean
60 dollar difference between just the display or display with frame I would go for with the frame . Can't imagine any water resistant front or back.
👏👏👏👏👏👏
👍
Main question still remains:- the water resistance😧
hi, are from iraq🇮🇶 ?
Hi, no I'm from US
Engineering marvel🎉
Why did Samsung do this. After keeping their screen replacement almost identical from Samsung s20 to s23 ultra, they finally changed the internal design,😢
👍👍😉
👍
I guess its cheaper now to replace samsung screen as the frame is not included to it.
Yup, there is still screen and frame combos, but its much harder to find since samsung is mainly doing screen only repairs now on the 24 ultra (I assume due to increased cost of the titanium frame).
Doesn't Samsung Replacement Screens come with the Frame attached now?
In this newer model, they mainly sell the screen itself now due to the titanium frame. However they do sell the combo also just harder to find since they do screen only replacements primarily for this model.
do a xperia 1 v teardown video
I have looked into it, but there are already a few teardowns of it on UA-cam and I usually don't get enough views on the sony phones to justify purchasing the device. So currently I don't have any plans to do that model but may look into doing the VI when it releases.
Why you dont iphone15 repair and screen change?
because of all the software locks, I don't bother much with iphones :)
Do samsung a55 please
soon, waiting for it to come in
No clamps ?!
Nice, long, informative video and as always, thank you for keeping the social/political nonsense out!
Thanks!
Iam Samsung ❤ but this one i give it to Apple 😢
Very good boro 🇮🇳 . give me samsung s24 ultra plz
Thanks!
Hiii
Hello
Batterie et Camera photo 📷 ⚠️⚠️⚠️😥😭
what kind of weird screen does the S24U have...
Idk but orange you tube looks hella fine
Ichiga suv kirmasligiga ishonchingiz komilmi
If it's done correctly, it shouldn't.
I recommend you disassembly Sony Xperia 1 v
I have looked into it, but there are already a few teardowns of it on UA-cam and I usually don't get enough views on the sony phones to justify purchasing the device. So currently I don't have any plans to do that model but may look into doing the VI when it releases.
But can you fix my life? 😂
😂
😂 idon.t know it was broken
Why no Exynos for the S24 Ultra????? Why only Spandragon for this? BECAUSE SAMSUNG KNOWS THEUR EXYNOS IS INFERIOR TO SNAPDRAGON, THATS WHY THEY DIDN'T TAKE CHANCES THE THWIR FLAGSHIP........
Snapdragon best stfu 😂😂
restaurado samsung galaxy s24 ultra 📱📲😉
👍
Remove rhe ear speaker as well,mine was full of dirt
You can watch the teardown video I did on the S24 Ultra to see that.
Just before launch, the weren't enough replacement parts.
👍
😢 murder of s24 ultra
if you want to replace the back glass, do what this lame video shows you. Otherwise, start by heating it up first. So lame...
Maybe you don't know how to listen to the video, where it clearly is stated to apply heat..
fake disassembly
fake comment
A LOT OF LOVE AND TNK A LOT MR.Bro FOR YOU FROM IRAQ...🇮🇶🇮🇶🇮🇶$%&*-+;'😎❤️❤️🩹❤️🔥💯💥💜💙🤍🖤🌹🌹🌹🌹🌹🌷🌷🌷🌹🌷... 0:24
👍
No ip68 anymore
So that thing has a screen size cooling copper 💀🫡
yup, most phones will have the copper film behind the screen to transfer heat. In addition to that, there is the vapor chamber (which not all phones will have) and graphite film.