Buy a trailer from Copart, so you can tow it yourself instead of having someone move your vehicle. That’s what I did, I saved so much money and you don't have to deal with the driver messing up your vehicles.
I don't think he goes to copart because some of them transport fees are high . He's buying from copart online from states around NC and paying for it to be transported from SC Virginia etc
@@BilalFlips Overall you doing good fam✊🏾! Yo vids helped me out when I started. I just didn’t want to run up the tab, to get a mf shady ass driver to deliver my car to my house or have it delivered to a mechanic shop.
Good to see you're back and killing it. Some advice: 1. Buy a multimeter and learn how to use it. On youtube, it's so easy. This can save you from scrapping a good battery where the problem lies elsewhere. Its like 10-20 bucks. 2. Buy a battery tester, same reasons as above. Also cheap. 3. With something small like changing the bulb is difficult due to a newer model year or different brand altogether. Get your phone out and search youtube/online. Like that bulb which is changeable form the front fender liner. 4. Protocol for cars with no dipstick. Turn on ignition (not engine start) and see if theres any prewarning about oil. Check underneath the car for oil leaks, and damage to engine sump. Usually we drain the oil and refill so we know there is oil in there. If you don't do the above you are risking starting an engine and seizing it, throwing thousands in the bin. If you dont want to do it from the drain plug below, get one of those oil vacuum machines. You can put the oil back in, if its good. All the above will add alot of money to your profits.
Just saying cause I work at advance auto, you can always just call and give your vin number and see if they have the piece instead of wasting time and money driving to 3 different stores
It literally says it in the screen mate, you should read it till the end. at 7:19 "The engine must be warm and TURNED OFF" you need to put the car in accessory/diagnostic mode then give it a try.
I’m surprised how many people don’t have AAA. It’s $68 and you get 4 tows a year up to 100 miles. You just paid $80 for 1 tow for only a couple miles. Crazy!
@@McDzy they don’t ask many questions. Just if you are the driver and what the issue is. Tire, gas, or won’t start so they know what to send. I used 3 tows in a week with them once. Also got towed about 100 miles before too. That was all when I was younger or in college. Saved me quite a bit!
P0300 is random misfire P0301 P0302 so on and so forth is misfire cylinder 1 misfire cylinder 2 Idk how replacing one fuel injector fixed the engine misfiring on all 4 cylinders
This was lowkey my first car I had back in high school 4 years and the amount of headache from oil to coolant leak having to be fix countless times, broken fuel line causing fuel to spray out from the hood, serpentine belt replace ( as a result of coolant leak speeding up its wear and tear) plus the 2-3 times I had to wait on the side of road waiting for a tow truck as a 17 years old . It was a good decision to get rid of it cost wise but deep down I still miss especially after watching this video😅
2.0T are good engines, if all the work has been done to them. Timing chains stretch around 100k miles and need to be replaced (new balance shaft chains and crank/cam chain with new guides), oil burning due to low tension oil control rings on the pistons which clog up (Needs complete teardown to replace pistons to revision DM pistons), PCV diaphragms tear and cause even more excessive oil burning (easy 10min job though), and underboost codes due to bad wastegate. If the chains and new pistons have been done, the 2.0T Gen 2 is a great engine, unfortunately its let down by these two major problems, especially the chains which can completely total the engine if it jumps timing. You can check if chain is stretched by going into the ECU, and checking the live data for "Camshaft phase adaptation, bank 1". If its more than 5 degrees, replace it. 6.84 degrees is about 3/4 of a tooth stretched and it definitely needs to be replaced. Also a dipstick can be purchased for about $15 from amazon and be put into the tube where you pulled that black nub out. My 2013 A4 allroad 2.0T made it to 165k before I was t-boned. I did chains and was about to remove the engine to replace pistons to fix oil burning (I was burning 1qt/900 miles right before car was totaled). To start the car, since it has the "Push to Start" button, you don't actually have to put the key into the key slot on the dash. You can start the car by getting in with key in your pocket and pressing the Push to Start. As a backup (and for lower trim cars without push to start), you can put your foot on the brake and push the key fob into the key slot all the way down to start the car.
@@gallitoalargado Timing chains, all in with OEM parts and the timing tools, was about $550 - $600. The pistons, if you can pull the engine yourself (this is a longitudinally mounted 4-cylinder, so its pretty easy) is about $1,400 with revision DM piston. Is it annoying, most certainly, but if you've done a decent amount of DIY work, this engine can be fixed up for cheap.
@@gallitoalargado Because the S2000 isn't a luxury sedan, its a mini sports car. They're completely different market segments. I doubt anyone who is looking at an A4 is cross-shopping with an S2000.
You don’t need a dib stick anymore cause you can tell it has dirty oil from the drip on the ground, you now need to change oil. Also some advice call the shops for the parts you need instead of wasting gas for disappointment lol 😂 love your channel tho
Nice job on the flip! How come you never include the DMV fees? I’m in Cali n I bought from IAA which is like Copart. I needed a CHP inspection and got raped with DMV fees to register it before I could sale it.
@@BilalFlips I mean that’s kinda misleading bro, flipping for you is $$$, but not for the average Joe that isn’t a dealer and is forced to pay DMV fees.
California is no good for flipping. lots of inspections and fees and taxes and notaries and bill of sale and blahblah that get in the way of the common man. Move from that god forsaken state
@@mohamedbenabdelmentalebthat is nothing but a rumor. My work truck cost more for parts than my merc. Name one part on a 2018 e450 that cost more than the same part in a 17’ gmc Denali. I’ll be waiting… rotors on truck $128.99 ea(did them last week), rotors on merc were less than $85/ea last time I did them. Hell let’s go to the extreme here, brand new replacement engine on the e450 is $7,899+ install straight from Mercedes. Replacement duramax for my truck is $16,500 for a USED “remanned” aka rebuilt engine. As for install cost, haven’t looked into it but I’d assume my truck cost about double as the cab has to come off the frame.
@@PitManenuver it is not a rumor, i am generally talking about keys and especially all keys lost for euro, for example 2015+ mercedes locksmith cannot add key since its a fbs4 system, the only way out is to get a copy made or tow it to the dealership which the key is around 800-1100 depending on if its a prox or non-prox fobik. I hope you get my point of euro cars being quite expensive on keys and programming. You are a mechanic i am guessing, i dont know too much in that category so dont have anything to say about it.
Yeah that's one thing I do t like about my audi no dipstick and also no tire pressure numbers it only alerts you when the pressure is off but you need to have a gauge to check
@@BilalFlips yeah I know because they want all the maintenance money.. I think audi might be higher than both mercedes and bimmer as far as labor hrs.. but it's the most fun car I've ever owned.. and I've had 1 s class and 3 7 series... nightmares
What app or platform do you use when you break everything down prices and time with the car, I use regular excel sheet but I like how you can add the picture of the car in the bottom.
So I'm confused... do you not actually work on the cars.. is this channel literally you buying a car and using mechanics??? What's the point then??? I rather watch someone actually fixing it and selling it. Not some wanna be
He's a flipper, doing what flippers do. Don't hate on a brother. Not all flippers are mechanics. Sometimes we can do small jobs ourselves.But we have to know when to call the professionals and he's doing a good job.
![Flipping a $7,000 Infiniti Q50 [STEP-BY-STEP]](http://i.ytimg.com/vi/U-jgChG4irw/mqdefault.jpg)
![Flipping a $7,000 Infiniti Q50 [STEP-BY-STEP]](/img/tr.png)
Buy a trailer from Copart, so you can tow it yourself instead of having someone move your vehicle. That’s what I did, I saved so much money and you don't have to deal with the driver messing up your vehicles.
Truth
@@carsnob If I was him I’ll have them neqros do it
I don't think he goes to copart because some of them transport fees are high . He's buying from copart online from states around NC and paying for it to be transported from SC Virginia etc
Don’t have the time for that brodie
@@BilalFlips Overall you doing good fam✊🏾! Yo vids helped me out when I started. I just didn’t want to run up the tab, to get a mf shady ass driver to deliver my car to my house or have it delivered to a mechanic shop.
Good to see you're back and killing it. Some advice:
1. Buy a multimeter and learn how to use it. On youtube, it's so easy. This can save you from scrapping a good battery where the problem lies elsewhere. Its like 10-20 bucks.
2. Buy a battery tester, same reasons as above. Also cheap.
3. With something small like changing the bulb is difficult due to a newer model year or different brand altogether. Get your phone out and search youtube/online. Like that bulb which is changeable form the front fender liner.
4. Protocol for cars with no dipstick. Turn on ignition (not engine start) and see if theres any prewarning about oil. Check underneath the car for oil leaks, and damage to engine sump. Usually we drain the oil and refill so we know there is oil in there. If you don't do the above you are risking starting an engine and seizing it, throwing thousands in the bin. If you dont want to do it from the drain plug below, get one of those oil vacuum machines. You can put the oil back in, if its good.
All the above will add alot of money to your profits.
Buy a better scanner and just call the parts store before driving there. Saves you time and money.
Just saying cause I work at advance auto, you can always just call and give your vin number and see if they have the piece instead of wasting time and money driving to 3 different stores
Good point, I’ll keep that in mind thank you
Exactly, I never randomly drive to part stores without calling and verifying if they have the part first 😂😂😂
you always suppose to change oil before turning it on if you don't know how long it's been sitting for
OR AT LEAST CHEK IT ON THE CLUSTER BEFORE STARTING THE ENGINE!! They also make an aftermarket dipstick that you can buy.
As long as the car has oil your good for small distances
Amateur hour
It literally says it in the screen mate, you should read it till the end. at 7:19 "The engine must be warm and TURNED OFF" you need to put the car in accessory/diagnostic mode then give it a try.
I’m surprised how many people don’t have AAA. It’s $68 and you get 4 tows a year up to 100 miles. You just paid $80 for 1 tow for only a couple miles. Crazy!
it can be buying a non running car and towing it to your place?? if thats the case i may buy AAA. let me know when you can brother, thank you
@@McDzy they don’t ask many questions. Just if you are the driver and what the issue is. Tire, gas, or won’t start so they know what to send. I used 3 tows in a week with them once. Also got towed about 100 miles before too. That was all when I was younger or in college. Saved me quite a bit!
@@Jagster7k hell yeah, no doubt.. i paid about 180 for a 20 mile tow,, idk if i just got robbed or something
i dont think aaa can tow off copart lot
P0300 is random misfire
P0301 P0302 so on and so forth is misfire cylinder 1 misfire cylinder 2
Idk how replacing one fuel injector fixed the engine misfiring on all 4 cylinders
it didn’t… that shits gonna blow eventually..
This was lowkey my first car I had back in high school 4 years and the amount of headache from oil to coolant leak having to be fix countless times, broken fuel line causing fuel to spray out from the hood, serpentine belt replace ( as a result of coolant leak speeding up its wear and tear) plus the 2-3 times I had to wait on the side of road waiting for a tow truck as a 17 years old . It was a good decision to get rid of it cost wise but deep down I still miss especially after watching this video😅
the plug you pull out, that’s the dip stick located, you need to buy one and you can check through that
Ahh
2.0T are good engines, if all the work has been done to them. Timing chains stretch around 100k miles and need to be replaced (new balance shaft chains and crank/cam chain with new guides), oil burning due to low tension oil control rings on the pistons which clog up (Needs complete teardown to replace pistons to revision DM pistons), PCV diaphragms tear and cause even more excessive oil burning (easy 10min job though), and underboost codes due to bad wastegate. If the chains and new pistons have been done, the 2.0T Gen 2 is a great engine, unfortunately its let down by these two major problems, especially the chains which can completely total the engine if it jumps timing.
You can check if chain is stretched by going into the ECU, and checking the live data for "Camshaft phase adaptation, bank 1". If its more than 5 degrees, replace it. 6.84 degrees is about 3/4 of a tooth stretched and it definitely needs to be replaced. Also a dipstick can be purchased for about $15 from amazon and be put into the tube where you pulled that black nub out. My 2013 A4 allroad 2.0T made it to 165k before I was t-boned. I did chains and was about to remove the engine to replace pistons to fix oil burning (I was burning 1qt/900 miles right before car was totaled). To start the car, since it has the "Push to Start" button, you don't actually have to put the key into the key slot on the dash. You can start the car by getting in with key in your pocket and pressing the Push to Start. As a backup (and for lower trim cars without push to start), you can put your foot on the brake and push the key fob into the key slot all the way down to start the car.
so much money and effort for a subpar car.
@@gallitoalargado Timing chains, all in with OEM parts and the timing tools, was about $550 - $600. The pistons, if you can pull the engine yourself (this is a longitudinally mounted 4-cylinder, so its pretty easy) is about $1,400 with revision DM piston. Is it annoying, most certainly, but if you've done a decent amount of DIY work, this engine can be fixed up for cheap.
@@mydimeisup5103 so much effort and money. Why not go Honda route and get an s2000
@@gallitoalargado Because the S2000 isn't a luxury sedan, its a mini sports car. They're completely different market segments. I doubt anyone who is looking at an A4 is cross-shopping with an S2000.
2:10 I love how he hid it in the wheel that’s hella nice lol
Liked the video, and ur tools they seemed affordable and reliable. Got any links?
-Scanner
-Jumper
-Air pump
Scanner: amzn.to/4dllIHK (amazon)
Air Pump: amzn.to/3SqsjbP (amazon)
Jump Pack: amzn.to/3Yk14na (amazon)
I appreciate the way u carry urself, not to cocky, nor arrogant and honest..
You could have gone online to check with the auto part store instead of driving around! Like you said time is money 😊
Have you considered if parts arent in stock to use FCP euro? OE/OEM parts for really good prices
I’ll look into them, thank you
I’m trying to get into this rn yo videos helping me fr💯 appreciate it
I love your videos im learning a lot
New to the channel what website do you use?
I like my Audi but the whole oil cpu not showing you engine oil pisses me off about my car
@11:40 You know you are down south when the tow truck driver is caring a gun on his hip lol.
Truth
Why you try to check oil level with engine on? Even the display give you the information you need...
You don’t need a dib stick anymore cause you can tell it has dirty oil from the drip on the ground, you now need to change oil. Also some advice call the shops for the parts you need instead of wasting gas for disappointment lol 😂 love your channel tho
You’re inspection at a regular mechanic ? Or smog type of shop and do they hook you up because of the dealer license ?
ماشاء الله تبارك الله وين تحصل السعر الأسطوري ذا على audi
Good informative video. Thank you. God bless you.✌👍
Buy yourself like a six or $700 actuel scanner and you can program your own keys
Do you have an actual brand and model you use and that really works?
@@andvivauctel
Hi I am from Kenya 🇰🇪 living in Qatar 🇧🇭 love watching your channel 👌🏾🙏🏾🙏🏾
Shout to Kenya! I’ve been wanting to visit Qatar, insha’Allah!
Salam bro! Another awesome video 💪🏼
Walaikum assalam. Thank you, JazakAllah kheir!
Hey brother, I had an A5, and these are really good cars if you take care of it and keep up with all the service items
love these videos keep it up
Preciate you !
Do I need a dealership license?
May allah grant you jannah brother
It shouldn't make u put the key in the port to start the car?? That's weird
I know you listed the gasket, injector and other parts, but what about the labor costs to change them? Feel like it’s not the true cost
its there mate 380usd.
There might be a spare key in the glove box Did you check? My 2015 q5 had one
If you are a dealer, why did you list Dealer fees?
Is this a Clean Title car? Salvage? Was the listing saying Run and Drive?
May Allah put baraka in the business brother
Ameen
As soon you said you going to pray first I commented Mashallah may Allah bless you and guide you 🙏🏽💯
You as well, Ameen.
آمين يارب العالمين بجاه النبي الأمين عليه افضل الصلاة والسلام
MashaAllah akhi. Alhamdullillah for the profits and good content, keep it up.
Jazakallah kheir
Nice job on the flip! How come you never include the DMV fees? I’m in Cali n I bought from IAA which is like Copart. I needed a CHP inspection and got raped with DMV fees to register it before I could sale it.
I’m a dealer so I don’t pay that
@@BilalFlips I mean that’s kinda misleading bro, flipping for you is $$$, but not for the average Joe that isn’t a dealer and is forced to pay DMV fees.
@@gilhdez196get your dealer license become a chad no Av Joe
California is no good for flipping. lots of inspections and fees and taxes and notaries and bill of sale and blahblah that get in the way of the common man. Move from that god forsaken state
Could you start including the mileage of these vehicles
Yeah good idea
Yeah good idea
Smart as hell I wish I would have got into this business
You still can
Salam Alaykum we make keys as well in nc and are license, for those type of audis we usually charge 250-300.
Expensive
@@TacticalRuse its a euro car nothing is cheap about it.
@@mohamedbenabdelmentalebthat is nothing but a rumor. My work truck cost more for parts than my merc. Name one part on a 2018 e450 that cost more than the same part in a 17’ gmc Denali. I’ll be waiting… rotors on truck $128.99 ea(did them last week), rotors on merc were less than $85/ea last time I did them. Hell let’s go to the extreme here, brand new replacement engine on the e450 is $7,899+ install straight from Mercedes. Replacement duramax for my truck is $16,500 for a USED “remanned” aka rebuilt engine. As for install cost, haven’t looked into it but I’d assume my truck cost about double as the cab has to come off the frame.
@@PitManenuver it is not a rumor, i am generally talking about keys and especially all keys lost for euro, for example 2015+ mercedes locksmith cannot add key since its a fbs4 system, the only way out is to get a copy made or tow it to the dealership which the key is around 800-1100 depending on if its a prox or non-prox fobik. I hope you get my point of euro cars being quite expensive on keys and programming. You are a mechanic i am guessing, i dont know too much in that category so dont have anything to say about it.
@@mohamedbenabdelmentaleb i think you are a cheat.
If low on oil the the computer will communicate notify on dash
Brother you are awesome. Can you please tell me how you are doing profit and roi in notes🎉
I’ll try to include that in one of my next videos
Was this a salvage or clean title? and in general, what type of title do you buy? Great videos brother!
Salvage and mostly buy salvage
*Here from morocco*
Keep up brother
May Allah bless you ameen
Loving these vids bro, looking to do some flips soon.
Preciate it, you got it
I subbed and liked the moment you said you were gonna go pray at the mosque. Keep up the imaan g 😘
This car is going to break down in a few months.
Hugh?
Why is that?
Yeah that's one thing I do t like about my audi no dipstick and also no tire pressure numbers it only alerts you when the pressure is off but you need to have a gauge to check
Idk why they do that
@@BilalFlips yeah I know because they want all the maintenance money.. I think audi might be higher than both mercedes and bimmer as far as labor hrs.. but it's the most fun car I've ever owned.. and I've had 1 s class and 3 7 series... nightmares
@@lifeisagambletv7 series are a nightmare
How do you actually make money to survive
Can we get a brief breakdown
What app or platform do you use when you break everything down prices and time with the car, I use regular excel sheet but I like how you can add the picture of the car in the bottom.
I just use the notes app on iPhone
@@BilalFlips thanks starting off with public auctions lien paper work, is their a way you recommend like to sell people cars with lien paper work
11:23 that jump was CLEAN
From Algeria
Machaallh bro ✌️
It has crack on shock absorber mount in front when he try to jump start vehicle. 😂😂😂 Good luck for new owner
🤡 🤡 stop hating, there’s no mf crack.
You could save alot of time by just calling the parts stores
Salute as always bro! From 919
Salute!
What area are you in?? Looks like Illinois??
SEEING U FROM BRAZIL. KEEP GOING WITH THE VIDEOS
Shout out Brazil!
Call before hand or check online instead of running around to different stores
Always put on hold unfortunately
Just got uh 2011 A4 don’t know what problem is on it yet
Is winter time a good time to start getting into buying cars?
Yeah why not
Amazing! Allah give you barakah habibj
You as well ameen
gotta hit it with the Bismillah every time
How do you buy cars where and what auction you using
Copart mainly
Love from New Orleans brother how do you buy from insurance companies?
Online auctions like Copart and iaa
@@BilalFlips do you need an auction license or do you use the personal one
مشالله إن شاء الله قريب🔥🔥
Insha’Allah
How is a 2015 Audi 7 Grand bro
Love the notes, I do the exact same thing
What website did you use to bid on the car bro ?
Copart
Salam brother what auctions do you go to im in the sc area looking to get started is copart better than dealer only auctions
Copart and iaa
@@BilalFlips are they better than dealer only auctions ?
does the auction place allow you to pay with business credit card
Yes but you get a discount if you pay with secured funds
mashsallah good content keep it up mn
salut de pe ce site ai cumparato
?
ERASING ENGINE CODES WITHOUT DRIVING THE VEHICLE IS CRAZY WORK 😭🤣
Thats standard, if they come back you know they are current.
Moroccan love
to save time next time just call the stores if possible they'll usually pick up and ask for the part number to not waste ur time
Preciate it but they always put me on hold for the longest time
New drinking game ! take a shot everytime he says alright yall
Drink water
@@BilalFlipsalcohol haram
At this point you should become a mechanic
How do you hop in every car and drive it around dealer tag?
Yeah
@@BilalFlips what state r you in Florida here
cool, great job.
Every German car part I get from fcp euro bro.
Good to know thank you
💪🏾
🤝🏼
Leading by bad example never drive without knowing the oil
Put it in reverse terry 💀
How much 😮😮
Can u start posting more please
Insha’Allah
Masha’Allah free game
So I'm confused... do you not actually work on the cars.. is this channel literally you buying a car and using mechanics??? What's the point then??? I rather watch someone actually fixing it and selling it. Not some wanna be
He's a flipper, doing what flippers do. Don't hate on a brother. Not all flippers are mechanics. Sometimes we can do small jobs ourselves.But we have to know when to call the professionals and he's doing a good job.
seatbelts at all times.
Guy lieing on the price
What the fuck did he say did he “Ahdi”
MashaAllah
Audis are not hard to work on
ALL AUDI ARE RUBBISH
Buy a better obd reader yours is absolute trash
Just bought a Audi a4 myself this shii nice ✅
Aye congrats!