Hii. I need your help. First of all, I have an Opel Insignia Sport Tourer 2.0 CDTI 2010. When I switch to reverse, it just flashes on my screen that the back sensor is supposedly on, but nothing is heard. I have a button for the front sensor but when I press it just a couple of times the light blinks and that’s it. Do you know where the sensor module is and what could be the problem that they are not heard? Can it be checked via Opcom?
Hi, i am in need of your help i hope you can. Here my problem; i have an astra 1.6t gtc and it is 2009 years. As you know,it has automatic headlight sensor, when i select auto mode and i go into a tunnel it runs my headlights but rear stop lights do not run but brake lights run when i make brake. İf i run headlight manually, rear stop lights work but as i said they do not run in automatic mode. How can i make these setting with op-com?
On auto I believe that in short time it's turns only DRL (Day running lights) and when they are on then in tailgate lights not coming on. But in night time should work all lights.
@@tolgaozkok3099 you can try to play with op-com like in this video ua-cam.com/video/ER8sXhFpCYc/v-deo.html But I don't think it will give some results.
Hello, I was wondering if you might know why but when I was doing a datalog, it wasn’t reading the RPM. I was doing normal driving and then I was doing full throttle acceleration and both times it didn’t read the rpm
Unknown ok thank you. Maybe I will try again when I have time. I did turn the car off completely and then started the car when it was all still plugged in so maybe that threw it off.
That can cause low battery power on coding. Normally when coding engine needs to run or must be strong battery. Common errors can be made with bad connection between ecu and computer
Hello, can i change display language for Zafira A?
Never tried but I believe there shouldn't be a problem
Hii. I need your help. First of all, I have an Opel Insignia Sport Tourer 2.0 CDTI 2010. When I switch to reverse, it just flashes on my screen that the back sensor is supposedly on, but nothing is heard. I have a button for the front sensor but when I press it just a couple of times the light blinks and that’s it. Do you know where the sensor module is and what could be the problem that they are not heard? Can it be checked via Opcom?
I don't think that you can check that with opcom. But the module normally is in boot on right or left side behind the panel.
good helpful video
How do you get all the different temperature gauges on the bottom of the screen please
I don't understand which you mean. There is no temperature gauge.
Unknown the numbers across the bottom of the screen please
Was going to attach picture but don’t know how to do it
My friend just told me that it’s for climate control
@@danielcoopey1746 that's already in car software inside. Those who got dual climate control they all got them.
Hi, i am in need of your help i hope you can. Here my problem; i have an astra 1.6t gtc and it is 2009 years. As you know,it has automatic headlight sensor, when i select auto mode and i go into a tunnel it runs my headlights but rear stop lights do not run but brake lights run when i make brake. İf i run headlight manually, rear stop lights work but as i said they do not run in automatic mode. How can i make these setting with op-com?
On auto I believe that in short time it's turns only DRL (Day running lights) and when they are on then in tailgate lights not coming on. But in night time should work all lights.
Unknown I also try in night time in auto mode, stop lights do not work in night too. They only run in manual mode..
@@tolgaozkok3099 strange. Stop lights should work all the time.
@@tolgaozkok3099 you can try to play with op-com like in this video ua-cam.com/video/ER8sXhFpCYc/v-deo.html
But I don't think it will give some results.
Unknown ok, i will try. Thanks a lot.
Hello, I was wondering if you might know why but when I was doing a datalog, it wasn’t reading the RPM. I was doing normal driving and then I was doing full throttle acceleration and both times it didn’t read the rpm
My guess that problem is with software or diagnostic cable because I never had that problem.
Unknown ok thank you. Maybe I will try again when I have time. I did turn the car off completely and then started the car when it was all still plugged in so maybe that threw it off.
@@xvReece that shouldn't be a problem. But you can try.
I can't do this on my 06 Opel Astra H ☹️ The options for the corporation type is grayed out for me. I have a BID display.
Probably your software version is different than mine.
@@--unknown-- I have Opcom V 1.70, if that's what you are talking about.
Here you can see what version I'm using. ua-cam.com/video/Ww7X8GEJC58/v-deo.html
Hello bro when i find it the color of display was black and white ... enney solution ?
I don't understand what you mean
@@--unknown-- I used op com and a problem occurred in the colors of the screen became black and white ...😢
That can cause low battery power on coding. Normally when coding engine needs to run or must be strong battery. Common errors can be made with bad connection between ecu and computer
@@--unknown-- Is there a solution ?!
@hichemsaifi2789 only if you saved "restore log file" before making changes. If not I'm afraid there is no way back. At least I'm not aware of that.
Need some help with my opcom
It says
Error I terface not found
I have a vectra c
Check this video ua-cam.com/video/Ww7X8GEJC58/v-deo.html
Maybe you didn't install the driver.