@@BCreativeDIY Yes, I tried with a wheel that was to big, the torque became too weak :( (I'm sorry for grammar mistakes, English is not my main language)
@@runningwithscissors7715 Yes, the 4wd has a lot of torque. I have put in the description the link with video "Hoverboard to OFF-ROAD 4X4 SEGABOT#5 - ( Electronics & Drive TEST )" . Success to built the go-kart. For go-kart, I approached a simpler but special version, I say. I also put a link in the description with video "Make an Electric GO-KART - Airplane STYLE // Hoverboard second LIFE"
Great guide! That looked like a straight valve, not a bent one. Is that correct? Does the valve foul the hoverboard at all? Have you remade the mud guards on the hoverboard?
Have you had any issues with the stem of the tube wanting to suck itself into the tire? Since that's not its natural position and it's twisted it seems to me it would naturally want to go where it belongs.
I have inflated the wheels and I can say that the valve was not pulled back. I'm going to test what happens when it's loaded. I'm a little worried if it withstands the 6 screws with which the hub cap is fastened. Now I build a platform with 4 wheels of this type. I hope to find time to complete and test it. I wish you a good day and thank you for your interest.
@@BCreativeDIY that's great. I'd like to see the platform with four wheels when you're done with it. If the tube does have a problem you could always take the tube out and fill those tires with foam. A lot of people do that.
Hello I did the same with the same size wheels but when inflating the wheel goes out of the perimeter of the motor. It works only if not inflated so much
Thats awesome i ended up drilling four holes and using the one hub cap and bolting on but makes trying to get them balanced a bitch and a half .... i need to try this ..... have you tried the no flats of the same size ?? I switch one of my front ends to no flats ... made a couple supped up power wheels with these motors
There is no way you used that size tire ..... what is the inside diameter of rubber tire because there’s no way i am getting this harbor fright tire of that size on that hub the way you did
@@addisonlather5536 You're right, the diameter of the rubber inside is really a little smaller than the hoverboard's hub. I used a little lubricant for the rubber and the hub and pressed hard. Honestly, I struggled a bit with this operation :). I hope I answered your question because English is not my native language and I am not sure I understood correctly what you meant.
@@BCreativeDIY ya i forget how much we rely on idioms sometimes. Feeling a bit like archer on pirate island.. but was gonna check out a few different sizes at the local store, might try a no flat ten inch tire and sand out more if it needs adjustment. I should upload a video just to show my go kart conversion but i probably won’t to be honest if only i could just drop a pic in chat
How does this affect the bearings and mounting hardware? Will it make the center point of the board sag more and put more bad kinds of loads on the bearings?
It's a purpose-made hole punch. Sometimes called a dinking punch. They come in kits of various sizes. When piercing rubber (various kinds exist), it's a good idea to avoid drilling -- hence, the punch. Drilling produces a very unclean edge. Rubber cuts more easily when it's lubricated, the punch is lubricated, or both are; liquid soap will do the trick. These punches will work better when the backing support -- usually a block of wood -- receives the cutting end of the punch on the end grain of the wood, rather than on the cross-grain. Finally, these punches tend to produce a slightly conical hole. This might be advantageous, given the application, so you'd do well to experiment with some similar material, and determine whether you'd prefer to punch from the outside in, or from the inside out...
I use 4.10 / 3.50 - 5 tires - normally used for agricultural machinery. This mean, WIDTH=4.1, PROFILE=3.5 and RIM SIZE=5, which result in a DIAMETER=2XPROFILE+ RIM SIZE = 2x3.5+5=7+5=12 inch (30.48cm).
Hola buenas, utilizo 4,10 / 3,50 - 5 neumáticos, normalmente utilizados para maquinaria agrícola. Esto significa neumáticos con dimensiones, ANCHO = 4.1, PERFIL = 3.5 y TAMAÑO DE LA LLANTA = 5 pulgadas. Considerando que 1 pulgada = 2,54 cm, los valores se pueden convertir a cm, esto significa (ANCHO = 10,414 / PERFIL = 8,89 TAMAÑO DE LLANTA = 12,7) en cm.
After wasting a lot of time searching the internet without success, I managed to order them at a local store that deals with sales of tires for agricultural machinery.
hi does anyone here know if its possible to get rid of the over speed "push back" feature on a ninebot mini pro i have made a wheelchair conversion but the push back is making it dangerous.thanks
I tried this on a 6.5 inch hoverboard wheel with a 5 inch inner diameter tire, no luck. It was too big. And the 4s are way too small... unless there is some way to stretch the wire inside the bead of the tire.
@@rjquibodeaux4004 I actually did get it to work. Its a bit make shift but there is a plumbing part for a toilet called a "metal flange ring". It worked for me as an adapter between the hub and tire. The 2 things worth mentioning: bigger tires = much less torque... so going over grass and stuff is actually more difficult because due to the motors lagging (at least for the weaker 350w hubs). Next is that the centering of the wheels is a bit more challenging since there isn't a true bead for the tire to sit in and align to. Best of luck to ya!
Creo que podría ponerse un motor en el cubo de una rueda de motocicleta eb el sitio del tambor de frenos para hacer una bicicleta eléctrica. Es sólo una idea, pero me queda la duda de si es capaz de moverse adecuadamente en una rueda de mayor tamaño.
What is the benefit of a bigger tire on a hub? There’s a debate with onewheelers who are angry that the new GT board uses a unconventional go cart tire custom size 11.5″ x 6.5-6.5″ but I’m sure it’s the same motor as previous model but the GT has a faster top MPH and claims to be 3 horsepower no idea what any of that mean community says the company made this tire to control where customers get the tire from which is them since no one makes these size tire… does having a bigger tire make any difference on a hub just curious it’s funny to see all the debate about it.. many claim it serves no purpose other than control so I dunno 🤷🏽♀️
Simply put, the larger your tire, the more of a grip your vehicle has on the road. As a tire's width increases, it covers more surface area on the road, larger wheels can go faster than the ones with smaller wheels because the radius of the wheel is larger they are also more stable at higher speeds. That’s what google says
В итоге автор понял что колесо не станет на транспорт и почему было принято решение сосок поставить вовнутирь,чем и какими знаниями руководствовался автор для меня остается загадкою,но все же было интересно смотреть
Хорошее наблюдение. Я решил установить клапан внутри, потому что подумал, что таким образом он будет более защищен, когда марсоход преодолевает препятствия. Мы использовали эти колеса для создания управляемой радиоплатформы 4X4, которая может перемещаться по пересеченной местности. Я поместил ссылку в описание на "Hoverboard to OFF-ROAD 4X4 SEGABOT # 5 ua-cam.com/video/SJ9LJA1GQ3k/v-deo.html"
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
Exactly what I needed! A mod that don't ruin the hub
I ❤️ this idea! Thank you for showing us.
Thanks for the measurements and useful video!
Also you are a legend for answering the comments. Subbed!
excellent idea, thanks for sharing it, I'm going to use it
That's what I was looking for, thanks !
I'm glad. However, keep in mind that the wheel size increases and therefore the traction torque decreases.
@@BCreativeDIY Yes, I tried with a wheel that was to big, the torque became too weak :(
(I'm sorry for grammar mistakes, English is not my main language)
@@BCreativeDIY but if you make it a 4wd then torque should stay the same....am currently buiding such go kart and will let you know the results :)
@@runningwithscissors7715 Yes, the 4wd has a lot of torque. I have put in the description the link with video "Hoverboard to OFF-ROAD 4X4 SEGABOT#5 - ( Electronics & Drive TEST )" .
Success to built the go-kart. For go-kart, I approached a simpler but special version, I say. I also put a link in the description with video "Make an Electric GO-KART - Airplane STYLE // Hoverboard second LIFE"
@@electrophotomechanics8797 your grammar is perfect :)
wonderful
The internet: "This will be $299.99. Each."
UA-camrs: "You got a hammer?"
❤
Thank you so much 💓 that is what I'm looking for...I have the haverboard .Can you please insert a link to buy the rubber wheel🙏😘
i am looking for this video longtime thank you
Nice idea! Will try tomorrow :)
Me ha costado un monton encontrar neumaticos 4.1/3.5-5 donde los conseguiste?
I tried but I couldn't. beautiful work
Какой внешний диаметр получился? 10 дюймов будет? Если так то это идеальный вариант для самоката ( переделка в полноприводный)
how did you get the wheels to fit i am struggling
What size is the hoverboard wheel?
Thanks
Great guide!
That looked like a straight valve, not a bent one. Is that correct?
Does the valve foul the hoverboard at all? Have you remade the mud guards on the hoverboard?
He made that look easy I can’t even add the tire to the rim
WOW 👌👌👌👌👏👏👏
😳😳😳😲😲😲😲😲Wooooow
Brilliant!
Nice ideia THX
Thanks for appreciation. I'm curious to see how it will work on the offroad terrain.
Какого диаметра поставили покрышку? На вид похожа на 14".
Колесо не проскальзывает?
1:17 на камере размер вроде наисан
Can you put a link to the tool you used to cut the hole in the tire? I'm struggling to find it.
it looks like a learherworking hole punch?
ARC punch
So I finally found the tire size and can’t get them on without a lot more grinding on the inside I’m guessing you just left out that part ?
Did you put some oil in the tire só the same can fit ?
Gonna try to make a battle bot with these bad bois
Que medida es la rueda grande?
Have you had any issues with the stem of the tube wanting to suck itself into the tire? Since that's not its natural position and it's twisted it seems to me it would naturally want to go where it belongs.
I have inflated the wheels and I can say that the valve was not pulled back. I'm going to test what happens when it's loaded. I'm a little worried if it withstands the 6 screws with which the hub cap is fastened. Now I build a platform with 4 wheels of this type. I hope to find time to complete and test it. I wish you a good day and thank you for your interest.
@@BCreativeDIY that's great. I'd like to see the platform with four wheels when you're done with it. If the tube does have a problem you could always take the tube out and fill those tires with foam. A lot of people do that.
Ban luar ukuran berapa dan ban dalem ukuran brapa .Mr???
Hello, You seem like you would know, what is the rim size on the all terrain 8.5 wheel? Can you put air filled tires on those motors?
Is this go for a regular hoverboard since I have a Go kart attachment would it work or I need extra parts
I have used the wheel from a common hoverboard 6.5 inch.
ممتاز
thanks
I'm guessing different tires have smaller variations and some might fit easier.
I'm yet to find one that would fit.
Hello I did the same with the same size wheels but when inflating the wheel goes out of the perimeter of the motor.
It works only if not inflated so much
so your saying the wheel rim needs to be bigger or smaller?
@@khabaabrufai281 bigger
Has anyone done this and installed it back into the original hoverboard? am trying this as well but struggling mounting the tires.
What tire size you used?
I use 4.10 / 3.50 - 5 tires - normally used for agricultural machinery.
Thats awesome i ended up drilling four holes and using the one hub cap and bolting on but makes trying to get them balanced a bitch and a half .... i need to try this ..... have you tried the no flats of the same size ?? I switch one of my front ends to no flats ... made a couple supped up power wheels with these motors
There is no way you used that size tire ..... what is the inside diameter of rubber tire because there’s no way i am getting this harbor fright tire of that size on that hub the way you did
@@addisonlather5536 You're right, the diameter of the rubber inside is really a little smaller than the hoverboard's hub. I used a little lubricant for the rubber and the hub and pressed hard. Honestly, I struggled a bit with this operation :). I hope I answered your question because English is not my native language and I am not sure I understood correctly what you meant.
@@BCreativeDIY ya i forget how much we rely on idioms sometimes. Feeling a bit like archer on pirate island.. but was gonna check out a few different sizes at the local store, might try a no flat ten inch tire and sand out more if it needs adjustment. I should upload a video just to show my go kart conversion but i probably won’t to be honest if only i could just drop a pic in chat
Классно
What is the size of the original hoverboard tire?
hello friend help me please, I have a motor of that inch so it is thinner, from one edge to the other it is only 27mm, will it work?
Where do you find the tires whith this size ?
On a local supplier. They had more connection than I could find on the internet :) .
Podpowiesz gdzie kupić taką oponę?
How does this affect the bearings and mounting hardware? Will it make the center point of the board sag more and put more bad kinds of loads on the bearings?
Extra stress on all parts yes. Its just extra weight, thats why there are "hoverboards" that are made for off road with beefier internals.
Hello
What is the name of the tool you use to make the hole in the tire and pass the valve? or is it a homemade invention?
You could use a drill bit if you wanted to, also that tool isn’t homemade
Sacabocados
It's a purpose-made hole punch. Sometimes called a dinking punch. They come in kits of various sizes. When piercing rubber (various kinds exist), it's a good idea to avoid drilling -- hence, the punch. Drilling produces a very unclean edge. Rubber cuts more easily when it's lubricated, the punch is lubricated, or both are; liquid soap will do the trick. These punches will work better when the backing support -- usually a block of wood -- receives the cutting end of the punch on the end grain of the wood, rather than on the cross-grain. Finally, these punches tend to produce a slightly conical hole. This might be advantageous, given the application, so you'd do well to experiment with some similar material, and determine whether you'd prefer to punch from the outside in, or from the inside out...
what is the size of the tire you use? any measurements?
I use 4.10 / 3.50 - 5 tires - normally used for agricultural machinery.
This mean, WIDTH=4.1, PROFILE=3.5 and RIM SIZE=5, which result in a DIAMETER=2XPROFILE+ RIM SIZE = 2x3.5+5=7+5=12 inch (30.48cm).
Qual as medidas desse pneu
Hola buenas de cuantas pulgadas es ese neumático
Hola buenas, utilizo 4,10 / 3,50 - 5 neumáticos, normalmente utilizados para maquinaria agrícola. Esto significa neumáticos con dimensiones, ANCHO = 4.1, PERFIL = 3.5 y TAMAÑO DE LA LLANTA = 5 pulgadas. Considerando que 1 pulgada = 2,54 cm, los valores se pueden convertir a cm, esto significa (ANCHO = 10,414 / PERFIL = 8,89 TAMAÑO DE LLANTA = 12,7) en cm.
@@BCreativeDIY vale muchas gracias
Can you put the tires link maybe aliexpress link thanks
After wasting a lot of time searching the internet without success, I managed to order them at a local store that deals with sales of tires for agricultural machinery.
@@BCreativeDIY ЗДРАВСТВУЙТЕ ПОСТАВЬТЕ ПОЖАЛУЙСТА ГЕОЛОКАЦЫЮ КАКОЙ ГОРОД ИЛИ РАЙОНЕ ГОРОДА И МНОГО ПОДПИСЧИКОВ ССУПЕЕРРРРР
hi does anyone here know if its possible to get rid of the over speed "push back" feature on a ninebot mini pro i have made a wheelchair conversion but the push back is making it dangerous.thanks
Send link tire
ada link tire mas?
What is the compound you applied on the rim and the seam of the tires?
I used vaseline for lubrication.
@@BCreativeDIY Oh thanks man
What tipe of maquinary use this tires?
Thank you
I have no idea. This is how I was informed by the supplier, whose specifics are the agricultural equipment.
@@BCreativeDIY can you share the name of the vendor or the link?
@@Andrei-zc6se I don't know how to say a supplier. I bought them from a local supplier that works in the field of agricultural equipment.
Try Tractor Supply Company.
Can you tell me an online site from where I can buy these tyres rather than a local shop
Try Tractor Supply Company.
Can I get the link to these wheels
Try Tractor Supply Company.
I tried this on a 6.5 inch hoverboard wheel with a 5 inch inner diameter tire, no luck. It was too big. And the 4s are way too small... unless there is some way to stretch the wire inside the bead of the tire.
Did you ever figure out how to make it work?
@@rjquibodeaux4004 I actually did get it to work. Its a bit make shift but there is a plumbing part for a toilet called a "metal flange ring". It worked for me as an adapter between the hub and tire. The 2 things worth mentioning: bigger tires = much less torque... so going over grass and stuff is actually more difficult because due to the motors lagging (at least for the weaker 350w hubs). Next is that the centering of the wheels is a bit more challenging since there isn't a true bead for the tire to sit in and align to.
Best of luck to ya!
👍
Salut, poti sa-mi dai te rog un contact sa comand si eu 2 cauciucuri?
hello friend help me please, I have a motor of that inch so it is thinner, from one edge to the other it is only 27mm, will it work?💥💥💥💥💥💥💥💥
what size tires do I need ?
4.10 / 3.50 - 5. I also mentioned in the description.
You put the inter two in backwards
عرض الاطار هو 4..10/3.50 -5
покрышку тоже разрежь, чтоб одевалась легко
would you know the matching size for the 200x90 hoverboard tire ?
I would like to do the same but with the bigger sized hoverboard wheels...
Good question. I'm interested in this information too.
The tires!!!where buy!!!!
I don't know how to say a supplier. I bought them from a local supplier that works in the field of agricultural equipment.
Try Tractor Supply Company.
My problem is that the axle won't go back in there's not enough room the tires rubbing real bad
Alguien sabe las medidas de las llantas o alguna liga ? Para poder comprarlas.
Would 4.10/3.50-4 tyres work
No.
Anyone else struggle to get the tries on? I can’t get one on really upset
What's that mean "...-5 tires" ??
Hi. (4.10 / 3.50 - 5 tires) , it is a tires with dimension WIDTH=4.1, PROFILE=3.5 and RIM SIZE=5.
La balbula debe estar por fuera
Creo que podría ponerse un motor en el cubo de una rueda de motocicleta eb el sitio del tambor de frenos para hacer una bicicleta eléctrica. Es sólo una idea, pero me queda la duda de si es capaz de moverse adecuadamente en una rueda de mayor tamaño.
What is the benefit of a bigger tire on a hub? There’s a debate with onewheelers who are angry that the new GT board uses a unconventional go cart tire custom size 11.5″ x 6.5-6.5″ but I’m sure it’s the same motor as previous model but the GT has a faster top MPH and claims to be 3 horsepower no idea what any of that mean community says the company made this tire to control where customers get the tire from which is them since no one makes these size tire… does having a bigger tire make any difference on a hub just curious it’s funny to see all the debate about it.. many claim it serves no purpose other than control so I dunno 🤷🏽♀️
Simply put, the larger your tire, the more of a grip your vehicle has on the road. As a tire's width increases, it covers more surface area on the road, larger wheels can go faster than the ones with smaller wheels because the radius of the wheel is larger they are also more stable at higher speeds. That’s what google says
Faster top-end speed, but slower off the line. More comfortable ride as there is more air/cushion and tire sidewall.
I actually don't fit on my hoverboard now I'm tired rubbing real bad
В итоге автор понял что колесо не станет на транспорт и почему было принято решение сосок поставить вовнутирь,чем и какими знаниями руководствовался автор для меня остается загадкою,но все же было интересно смотреть
Хорошее наблюдение. Я решил установить клапан внутри, потому что подумал, что таким образом он будет более защищен, когда марсоход преодолевает препятствия. Мы использовали эти колеса для создания управляемой радиоплатформы 4X4, которая может перемещаться по пересеченной местности. Я поместил ссылку в описание на "Hoverboard to OFF-ROAD 4X4 SEGABOT # 5 ua-cam.com/video/SJ9LJA1GQ3k/v-deo.html"
ua-cam.com/video/iOKxdxVf_x0/v-deo.html -- Hoverboard to OFF-ROAD 4X4 SEGABOT#4 - ( DIY Mechanics )