Literally have a 2009 beetle and this exact same thing happened to me today. Autozone makes a kit, it cost $30 and took LITERALLY 30 seconds to snap on
My jetta wouldn't start after installing the doorman diaphragm, so I switched it back to the original, though it did have a small tear and was filthy. I will be going to the shop this week to see what's going on with the rough idle.
Same part first purchased for 2010 Jetta 2.5L from local auto supply place and installed. That generated new code P2187 in two days, Found the diaphragm was not seated properly, I found lots of air was leaking and the PCV valve diaphragm was not seated. Press around upper three tabs and found there was a slack but the tabs was seated fine. The lower tabs had no slack on finger press but upper three do. Thought may be the parts cap and diaphragm were defective. Spent another $40 and purchased from Autozone and installed very carefully. This time I was able to open the oil fill cap quick to check PCV when engine was idling. After two day I found the new one failed with the same symptoms. The upper tabs were not holding the tight enough and PCV was leaking air. I stick a temp clamp to hold the cap tight, it was still leaking some but was able to open cap on idle. Now I am stuck, what is the problem. Why the all three upper tabs are not holding tight enough. I do not see any damage on tab!!!
Had exact same issue. Fixed by using upgraded diaphragm by RKX (google them). They make it thicker and side clip tolerance clicks and hold tight and well..
Hello sir thanks for the video. I just replaced the PCV valve as recommended. However, the old one had no tears or holes in it. Of course it was dirty but nothing that indicated an air leak...I still put the new one in obviously but I'm worried this won't fix my problem. I'm having a problem where my car shakes when idle and sometimes it even dies and I have to restart. I've gotten the code ran at my local VW dealership and they said it needs a new map sensor....but I've been told by longtime mechanics that the throttle just needs to be cleaned out
Hello John, I would do a smoke test before anything else, if you have a vacuum leak it might effect the MAF sensor too, google how to make your own vacuum pump, it’s not very complicated, 🙏🏻
during my repair for this, i accidentally screwed up the duct when using the channel locks to loosen the clamps... now i can’t get the clamp to go back up to its locking position. any advice? if it is punctured is that gonna make the problem worse? 😓
I usually do it with channel locks but in your case you might want to use the special pliers, you can buy it from Amazon, its not good if its punctured.
Mine idle is weird and after it heats up goes fine. If i start and stop 3-4x straight it gets worse and stops by it’s own! Gave it some gas and runs fine. Coil pack problème?
So if the diaphragm is good and you take oil filler cap off while it's idling, is the motor supposed to surge? And should there be resistance when you take the cap off due to vacuum in the crankcase? Thanks
Hi Sam, the Pcv system is an enclosed system , so if you remove the oil cap that could be as if it had a larger vacuum leak which would make it stall, remember that if you have an engine with worn piston rings it could cause strong blow by, if I was to do an oil cap test I might as well do a vacuum test with a gage at the same time, the closer to 18-22 psi the better 👍🏼
@@hugoscreations You mean another 1 it's not in the video is a turbo Is that what you mean Mine doesn't even make it hissing noise On the PCV valve and you put your finger over and it doesn't change anything
@@benden4249 you are right it’s another one, I’ve actually done a few already, taking out the cap on the diaphragm it’s only one of the process of elimination, the problem is when the cap’s locks brake than you have to replace it regardless
The dorman one that they sell at auto zone didn’t work for me. The holes for locking it in place were distanced apart differently. I’m gonna try one from Amazon - see if that works
I believe you are right about the doorman Friend. I replaced mine last year and it is now leaking oil causing my map sensor to be implausible with a P0106 engine code. I notice oil in the intake manifold..so about 400 to 500 miles cleaning the damm map sensor & the intake manifod when the check engine light comes on with a P0106 code
Literally have a 2009 beetle and this exact same thing happened to me today. Autozone makes a kit, it cost $30 and took LITERALLY 30 seconds to snap on
This video just saved me. My car is running perfectly now
Glad to hear that!
Holy Sh*t, after 5 months of searching, i think this solved the problem on my 2008 Jetta
Gracias,Hugo, it was my car problem now it's working good.
Good to hear that!
Thx just save my day been screwing with the Jetta for 6months ...
Awsome!
My jetta wouldn't start after installing the doorman diaphragm, so I switched it back to the original, though it did have a small tear and was filthy. I will be going to the shop this week to see what's going on with the rough idle.
Same part first purchased for 2010 Jetta 2.5L from local auto supply place and installed. That generated new code P2187 in two days, Found the diaphragm was not seated properly, I found lots of air was leaking and the PCV valve diaphragm was not seated. Press around upper three tabs and found there was a slack but the tabs was seated fine. The lower tabs had no slack on finger press but upper three do. Thought may be the parts cap and diaphragm were defective. Spent another $40 and purchased from Autozone and installed very carefully. This time I was able to open the oil fill cap quick to check PCV when engine was idling. After two day I found the new one failed with the same symptoms. The upper tabs were not holding the tight enough and PCV was leaking air. I stick a temp clamp to hold the cap tight, it was still leaking some but was able to open cap on idle.
Now I am stuck, what is the problem. Why the all three upper tabs are not holding tight enough. I do not see any damage on tab!!!
Did you ever figure this out ?
Had exact same issue. Fixed by using upgraded diaphragm by RKX (google them). They make it thicker and side clip tolerance clicks and hold tight and well..
Hello sir thanks for the video. I just replaced the PCV valve as recommended. However, the old one had no tears or holes in it. Of course it was dirty but nothing that indicated an air leak...I still put the new one in obviously but I'm worried this won't fix my problem. I'm having a problem where my car shakes when idle and sometimes it even dies and I have to restart. I've gotten the code ran at my local VW dealership and they said it needs a new map sensor....but I've been told by longtime mechanics that the throttle just needs to be cleaned out
Hello John, I would do a smoke test before anything else, if you have a vacuum leak it might effect the MAF sensor too, google how to make your own vacuum pump, it’s not very complicated, 🙏🏻
I meant to say smoke pump, sorry!
during my repair for this, i accidentally screwed up the duct when using the channel locks to loosen the clamps... now i can’t get the clamp to go back up to its locking position. any advice? if it is punctured is that gonna make the problem worse? 😓
I usually do it with channel locks but in your case you might want to use the special pliers, you can buy it from Amazon, its not good if its punctured.
Time to eat a chicken after hearing this video.
04:01 my car did not make that sound though! What am I doing wrong?
If you have those plastic trim removing tools its better to use when taking off the cap. Harder to break plastic on plastic.
you are right, thanks!
True but most kits come with a new cover.
Mine idle is weird and after it heats up goes fine. If i start and stop 3-4x straight it gets worse and stops by it’s own! Gave it some gas and runs fine. Coil pack problème?
Did You fix it?
Having the same problem 😢
@@Chris-jc9nw had wire issues / throttle body
The Gallos are hungry!🐓🐓🐔🐔
So if the diaphragm is good and you take oil filler cap off while it's idling, is the motor supposed to surge? And should there be resistance when you take the cap off due to vacuum in the crankcase? Thanks
Hi Sam, the Pcv system is an enclosed system , so if you remove the oil cap that could be as if it had a larger vacuum leak which would make it stall, remember that if you have an engine with worn piston rings it could cause strong blow by, if I was to do an oil cap test I might as well do a vacuum test with a gage at the same time, the closer to 18-22 psi the better 👍🏼
Thanks Hugo!!
Rooster good job
Thank you!
You're welcome!
Chicken: ehohehoeh.....Fixed.
I lost the spring but everything else is good. Is there anywhere i can get a spring?
If you have an LKQ near you, they should have many there
What sensor is that on the air intake duct
Hello Romi, that's the air charge temp sensor,
Hi Hugo I don’t think I have that problem but when I try and start my car it sounds like a vacuum and it doesn’t start at all
Can you help me
Hi Reyna, if you step on the gas pedal about 1/4 of it it should start even with a vacuum leak. if it don't start than you have a different problem.
@@hugoscreations I have done that and it still didn’t start
Thank you for good Video.
Our pleasure!
I'm glad it helped!
I heard the ones from Dorman didn't work?? I think that was a turbo version?
Yes it’s turbo, so far so good after 1 year!
@@hugoscreations You mean another 1 it's not in the video is a turbo Is that what you mean Mine doesn't even make it hissing noise On the PCV valve and you put your finger over and it doesn't change anything
@@benden4249 you are right it’s another one, I’ve actually done a few already, taking out the cap on the diaphragm it’s only one of the process of elimination, the problem is when the cap’s locks brake than you have to replace it regardless
The dorman one that they sell at auto zone didn’t work for me. The holes for locking it in place were distanced apart differently. I’m gonna try one from Amazon - see if that works
@@fixitall85 update? on amazon part
Would this cause a check engine light to come on? I suspect this is my issue amd is leaking oil and making my map sensor tweak out.
Yes it will, it’ll throw lean condition codes as well as evap codes, aside of messing with the air flow meter.
Don't waste your $20, doorman crap doesn't work for very long. Spend the $200 on a new valve cover.
I believe you are right about the doorman Friend. I replaced mine last year and it is now leaking oil causing my map sensor to be implausible with a P0106 engine code. I notice oil in the intake manifold..so about 400 to 500 miles cleaning the damm map sensor & the intake manifod when the check engine light comes on with a P0106 code
I can’t find the part number
What year and model is your car?
If it’s like the one on this video it’s Dorman 917-064
@@hugoscreations 2011 VW Jetta SEL with the 2.5L
@@THEPOSSUMNUTS it should be the same dorman number 917-064
Hey you have roosters
Was there a retaining spring in the original diaphragm?
Yes there was.
@@hugoscreations thanks for the video. I changed mine and the rough idle is fixed.
Press this little thing right here..
Also know as satans little clips. 😆
I hate these clips!
Only thing i dont like about VW.