hello brother, nice video, can i have some pointers for all of us,.... Scenario1:. Need not to crack open the Inlet steam valve, make it full open position same with the Outlet steam valve of Fuel oil heater, let alone the the temperature controller control the set point temperature of fuel oil. (Condition: Inlet /Outlet , temperature control valve no leak) Scenario 2: In case temperature control valve are leaking or the controller set point are lagging please control the set temp. at steam outlet valve not in steam inlet valve. ( procedure has to be done this way for easy isolation of steam and to avoid fatigue/damage to inlet steam valve seat or during steam heater maintenance) If a controller has a delayed response you may send it ashore for recalibration or if the valve are leaking change it with new or reconditioned spare on board if available.... Thank you☺️
Thank you so much for the information and ideas Sir. ❤ Maybe that will apply to some of the heaters on board not to Purifier Heater. Because if we fully open the inlet valve of Purifier heater the temperature will rise and alarm for High Temperature Fuel oil will occurs.
It is used for opening and closing the bowl of purifier as well as sealing Sir. Opening of bowl means discharging sludge and closing the bowl for purification process.
After you lined up and open the necessary valves for operating the purifier and set the temperature setting Sir Start the feed pump. In some ship feed pump is separate and its not coupled to the purifier motor, Starting the feed pump or purifier starter motor the fuel will go to the heater for heating and going back to Settling tank. If the temperature is at the setting you set (98°C usually) start or push the auto start of Purifier.
Usually, is goes to the sludge tank, eventually transfers to the BOT or bilge oil tank, then transfer the waste oil tank, where in it will be incinerated by the incinerator
Operating water is for opening and closing the bowl sir, Opening of bowl for discharging and Closing the bowl for purification. Sealing is to provide separation line or interface between two liquids.
Pwede naman po applicable lang po yun kapag nagpalit ka ng main seal ring or pilot valve o-rings para maexercise at maglapat masyado ang seal ring sa main cylinder. Pero samin after auto start saka mag discharge test. Para malaman kung walang leaking at talagang nag didischarge.
Would you explain about backpressure And where are we can found place of that bypass/fo flow adjustment valve? And how much the pressure on inlet and outlet valve of purifier?
Thanks for the video sir . Very clear precise and informative . I hope you can upload more informative videos . More power and smooth sailing sir 👍👍
salamat po sa video sir na kung pano po ang operation and starting ng purifier godbless po laking tulong po ito sa gaya ko na ratings sir
Lupet mo lodi precise ang explanation mo
Very clear explanation at may actual video or photo pa nung ineexplain, I subscribed po, I hope you continue making vids like this very helpful po.
Thank you so much for watching and subscribing Sir💖
Thx you engineer you are best
Hi brother u vds r just outstanding very neat clean simple to understand ❤❤keep it up
Watching Chief, nice sharing, thumbs up
Thank you Ta❤❤❤
Very useful your videos.Thank you very.
Support here.. 😊 more ideas to learn here.
Detail Explainaton.... Thank you for your great efforts❤️🔥
Kudos sir. Very precised and informative❤️❤️
Thank you Sir hehe ❤
Very nice good explanation tq
Thankyou so much! Galing talaga video nyo sir! 👏🏻 Napaka simple at informative, gawa pa po kayo madaming videos. God bless po. Naka subscribe na ako.
Thank you for watching and subscribing Sir❤😎
Thanks.for the information sir.
More knowledge to share labs
❤️❤️❤️❤️
Very educational po salamat 🙌
Thank you for watching Sir❤
Thank you sir Godbless po please more videos and knowledge Ingat po palagi sir ❤️❤️
Thank you for watching Sir❤
Nicely explained
Goodjob sir!
Informative sir❤
Thanks for this clear explanation! Please sir can you do boiler & steam system operation??
Noted Sir.❤ Thank you
hello brother, nice video, can i have some pointers for all of us,.... Scenario1:. Need not to crack open the Inlet steam valve, make it full open position same with the Outlet steam valve of Fuel oil heater, let alone the the temperature controller control the set point temperature of fuel oil. (Condition: Inlet /Outlet , temperature control valve no leak)
Scenario 2: In case temperature control valve are leaking or the controller set point are lagging please control the set temp. at steam outlet valve not in steam inlet valve. ( procedure has to be done this way for easy isolation of steam and to avoid fatigue/damage to inlet steam valve seat or during steam heater maintenance) If a controller has a delayed response you may send it ashore for recalibration or if the valve are leaking change it with new or reconditioned spare on board if available....
Thank you☺️
Thank you so much for the information and ideas Sir. ❤
Maybe that will apply to some of the heaters on board not to Purifier Heater. Because if we fully open the inlet valve of Purifier heater the temperature will rise and alarm for High Temperature Fuel oil will occurs.
Sir more videos about the machineries in engine room, thank you so much sir
Noted Sir Thank you for watching❤
Thanks for the video. What is the fresh water supply used for in the purifier? Cleaning out sludge?
It is used for opening and closing the bowl of purifier as well as sealing Sir.
Opening of bowl means discharging sludge and closing the bowl for purification process.
Opening the inlet and outlet valves
fully or crack?
Stay safe bro.
You gained a new subscriber today bro, do more videos - I promise to like, share
Thank you so much Sir.❤
Thank you!🙏
Wow nays nays
Sana olllll
Salamat po Sir.
Sir about naman po sa Lube purifier system po ng M/E po, sana po maituro niyo din po Sir salamat po.♥️🙏
Kindly check my new upload po. 😁❤
And How to start Lub oil purification ? the same way ???
Nice video
Same procedure Sir. The difference is the maintaining temperature and feedrate only
Super 💯
Good
Let me know how to adjust pressure, temperature and feed rate setting
nice
Sinubscribe ko kau sir..dinownload ko rin po ung videos nyu babaonin ko sa barko... Salamat po
Salamat Sir. 😉❤
Approved! ❤
Make video on Alpha level purifier
Excellent Training.9/30/2022yr
My bruv what is the mm function means? Can just tell me in simple words. Thank you for doing gods work.
Its Multi Monitor ON Sir. For activation of alarms if their is any abnormalities in Purifier, such as Oil leak, No opening of bowl etc..
Ty lodi
Sir pwedi po video ng ballasting at deballasting tapos bildge pumpout.
Sige po Next time. Thank you for watching Sir❤
What is significance of bcak pressure valve in purifier
When do you start the feed pump . you have to start the feed pump then only fuel temperature will increase. Pls explain.
After you lined up and open the necessary valves for operating the purifier and set the temperature setting Sir Start the feed pump. In some ship feed pump is separate and its not coupled to the purifier motor, Starting the feed pump or purifier starter motor the fuel will go to the heater for heating and going back to Settling tank. If the temperature is at the setting you set (98°C usually) start or push the auto start of Purifier.
What is done with the sluge after removed by device ?
Usually, is goes to the sludge tank, eventually transfers to the BOT or bilge oil tank, then transfer the waste oil tank, where in it will be incinerated by the incinerator
@@ElChavacano22 does the waste oil incynator (sp) power any steam to electric generator?
@@solstar4778 is does not supply power to the generator, but before it's incinerated it will be heated by steam then it can be burn
@@ElChavacano22 🤔a thought maybe just that ,and make the progress more efficient? And make you money ?
sir how does sealing water and operating water works?
Operating water is for opening and closing the bowl sir, Opening of bowl for discharging and Closing the bowl for purification.
Sealing is to provide separation line or interface between two liquids.
Hello sir bago ba i-auto start kailangan ba na i-manual discharge muna o hindi na? Salamat sir
Pwede naman po applicable lang po yun kapag nagpalit ka ng main seal ring or pilot valve o-rings para maexercise at maglapat masyado ang seal ring sa main cylinder. Pero samin after auto start saka mag discharge test. Para malaman kung walang leaking at talagang nag didischarge.
what is MM ON button sir?
Multi Monitor ON Sir so that the alarms will activate/ sounded if their is abnormalities in Purifier.
Thanks
Ano po agency niyo sir sa apex. AQUALINK poba??
Apex po . Pero Bouvet Shipping po ang Manning
Sir any 3 reasons why oil purifier is using water???
For sealing, opening the bowl for discharging and closing the bowl for purification
Would you explain about backpressure And where are we can found place of that bypass/fo flow adjustment valve?
And how much the pressure on inlet and outlet valve of purifier?
sorry sir..if you to make safty dont make switch on to MM before check oil leakage to pur..becouse nobody know when the pur is dischg
Panahon namin walang nakalagay na position sa cover all namin
Optional lang din ngayon Sir kung maglagay ko or hindi. Pero pag sa port na may mga authorities need po.
Very dangerous when checking leaking oil.
Please reply fast
Poor purifier representation.
Noted. I will make it better❤
very useful ！but i want to ask sth detail how could i contact you？
You can direct message me through my facebook and messenger (Christoper Pimentel)