yeah so i got a fg25n that has a little throttle response.. like you floor it, it raises rpms very slighty. like 15-20%, got e-24 and e-31 code. should i try what you did here, or is there another route i should be taking ?
I am assuming the field tech is new at his job. Not following through with the setup procedure is a little sad. thanks for sharing another job with us.
I think what would be neat is if you did a video featuring the different electrical diagnostic tools that you use and why you chose to use one instead of the other and maybe even how they are used correctly or at least how you use them i believe that would really help a lot of techs maybe encourage them to troubleshoot instead of parts changing also where do you obtain your info like the 0.6vdc and the 0.3vdc info.
Have you Run into the E31 throttle issue on the K21 engine? I’m having this issue on my unicarrier. E31. Limp mode throttle response What are some troubleshooting steps to take? Thank you 😊
Hi mate please help me with AL 86 fault code on an electric forklift JungHeinrich, very erratic throttle response, only works when its started in morning then as soon as this code comes up no more throttle response at all
Code popped up from some kind of fault. The tech called the pod which was right, but didn’t catch the adjustments. It’s happens to the best of us and they’ll not make the same mistake again. I’ve been a tech for years and just the other day I installed arc lights. Plugged everything in flipped the key switch and nothing. Troubleshooted for 2 hours. The ground wire to the relay looked connected from a certain angle. Plugged it in let there be arc lights.
Thank you so much for this video. This information has helped me many times .
Its great when you get a Mitsi or Cat with an OBD2 port to be able to clear down DTCs. Its so much simpler than 'the pedal dance'!! 🤦♂️🤦♂️😁😁👌👍
yeah so i got a fg25n that has a little throttle response.. like you floor it, it raises rpms very slighty. like 15-20%, got e-24 and e-31 code. should i try what you did here, or is there another route i should be taking ?
I am assuming the field tech is new at his job. Not following through with the setup procedure is a little sad. thanks for sharing another job with us.
Maybe the field mechanic didn't have the repair manual
No rpms when pressing throttle
I would've just done the pedal dance
Mantap
Changed throttle pot
Ibe watched all of you video and its very informative
I think what would be neat is if you did a video featuring the different electrical diagnostic tools that you use and why you chose to use one instead of the other and maybe even how they are used correctly or at least how you use them i believe that would really help a lot of techs maybe encourage them to troubleshoot instead of parts changing also where do you obtain your info like the 0.6vdc and the 0.3vdc info.
The voltage readings are in the service manual.
Have you Run into the E31 throttle issue on the K21 engine?
I’m having this issue on my unicarrier.
E31. Limp mode throttle response
What are some troubleshooting steps to take?
Thank you 😊
Hola genio, tenés un cat p5000 , funciona bien a gasolina pero no quiere funcionar a GLP , llega bien GLP hasta el inyector de GLP
Hi mate please help me with AL 86 fault code on an electric forklift JungHeinrich, very erratic throttle response, only works when its started in morning then as soon as this code comes up no more throttle response at all
Code popped up from some kind of fault. The tech called the pod which was right, but didn’t catch the adjustments. It’s happens to the best of us and they’ll not make the same mistake again. I’ve been a tech for years and just the other day I installed arc lights. Plugged everything in flipped the key switch and nothing. Troubleshooted for 2 hours. The ground wire to the relay looked connected from a certain angle. Plugged it in let there be arc lights.
What a rook. Basic stuff that should've been solved out in the field. Transport fees to the shop is easy $500 one way
Bro how about a "D83" error?
I’m a field tech myself and I would like to know where you get all of the paperwork you have . It would be extremely useful for me to
They are company supplied
FYI if you get a bit better scan tool , it will read P codes which can be very helpful.