I just bought the FLYSKY I6X , setup is exactly the same as you describe , except the I6X allows you to assign switches as a channel , which actually makes the setup a little easier , but works so well on my 1.8 meter Piper Cub :) , Cheers Andrew !
I could use some help setting mine up . I tried for 3 hours today . I have the FS-i6 but mod to 10 channels so it's like the FS-i6x .... I'm trying to put the flaperons on ( C )switch 1,2,3 the other 3 are taken . And I don't want it on the sliders dials . Not sure you will even see this comment. But I thought I would try to reach out , you made it sound easy . Much respect 👏
Thanks Andrew for all the info you share, it has been really helpful to me and thousands of other people. You explain everything clearly. Great job Cheers Brian NZ
Hey Andrew, thank you so much for this video. Ive been looking to set flaperons on my new Hobbyking EZIO but couldnt get it to program to a switch. Thanks to you i've now been able to do it. Cheers mate!
I realize I needed mix 3 for the servo on channel 5 but that doesn't change what happened. When I wrote potentiometer 1 I meant potentiometer A. It seemed that as soon as I adjusted the positive and negative that's when trouble started. I want to use the potentiometer but have just 1 battery left and am reluctant to attempt that program again. I think you owe me a battery. Best of spirits!
The UBEC provides no ground from batt to Rx but then neither would the average 4AA pack. The battery is an eflite. Quality pack. UBEC is generic but had no problems until I wanted to use the program you provided for potentiometer use. I purchased two new packs but don't want those fried too.
I have a 2s 120mah 20c into a 5v ubec then onto the FS I-6 Reciever I successfully connected a servo to channel 1 with the first mix being 5 slaved and another servo to 5. I had servo function then I added mix two with potentiometer 1 with channel 1 slaved to that I adjusted the potentiometer and only one servo moved I started to adjust positive and negative to find control for both servos from the potentiometer and the servos started sizzling, trembling and going all over the place. I removed the potentiometer from the mix. After that I found that there was no servo response at all. Re binded the Rx and nothing still. Thought battery was dead and plugged it into the charger. Error response from charger. Looked at battery and noticed it had ballooned a little. Plugged in another battery and Rx and servos are ok. That program you instructed on using the potentiometer for flaperon mixing fried one of my batteries!
thanks Andrew......had my fsi6 for a while and never got around to using mixes ... now when i need them i can check out your vids for an easy tutorial ...and congrats on the 10 k .
Hmmmmhhhh.....I don´t understand how it works...... And where do You connect the servos ??? This vid is just what I looked for ! I`m just assembling a new Multiplex indoor funnycub, and it needs just those flaperons. Thank You very much !
ACE !!!! MANY MANY THANK YOU'S !!!! was looking for an easy solution to having flap function with just ailerons for ages :) and video so easy to follow. keep up the great informational vids ( esp for the FS-i6 ) CHEERS !!
Hi Andrew. I must say that your channel is great, informative and helpfull. I have started to fly RC planes in about half a year ago and learnd a lot from your channel. I have just finished to build Photon from from ExperimentalAirlines by Ed, and as I have FlySky i6 I really like your tutorial how to set Flaperons, which I want to use. Here comes the problem. I have two separate servos plugged in to channel 1 and channel 6 is right aileron. I have settup the radio the same way as you describe. It works... "but" my ailerons are reversed. You mentioned in the video that we should change positive and negative mix to either 100% or -100%. Ailerons are wokring in the separate direction as they should when I set 100%, but reversed. If I choose -100 on positive mix both are up and for my understanding negative mix left aileron should go down, but id does not. If I have both mixes on mix#1 on -100 both ailerons go up. But if I have 100% it works but reversed. Can you please help me to figure out the problem? My goal is to use separate leads for servos, and have flaperons for soaring. I would really appriciate any help and any advice. Thank you in advance. :)
Hi Martin. Photon was my first plane too. I would start from the beginning with your mixing. Just plug in the L aileron to Ch1 and get it working in the correct direction. Select Reverse for Ch1 if it's working in the wrong direction. Then my instructions should work for you. Good luck.
Hi Andrew, I must say that your answer kind of helped. :) I got it working eventualy, just had to set up new plane on the radio and start from CH1, put it to revers, played with it for about 20 min and got it working :D juhuu :) Now just waiting for a windless day to maiden it. Thank you anyway :)
Hi Andrew, being a man of immense RC knowledge, can you answer a question for me? I would like to program Flaperons on a Volantex G2 but I have a BGL-6G-AP GPS Flight Stabiliser on board. As the Ailerons have to be split using Ch's 1 & 6 on my FlySky I6 Controller, is there anyway around this as the FC gets the Aileron commands from Ch 1 on the controller and uses a Y cable? What do you think?.....Best regards, Pete
@@AndrewNewton Thanks Andrew, yer that's what I thought. Shame really cos you can't have GPS/RTH for FPV & Flaperons. That will be something for the FC Manufacturers to think about, it could be done with an extra FC Ch. :) Happy Flying, regards, Pete
Pretty easy to understand the case when you mix a channel into itself. The radio executes commands in sequence, like a flowchart. 1. take the value of CH2 2. modify it by the amount given in the mix 3. write it back to CH2 4. output the final value to CH2's port, or display it, or whatever 5. goto 1. For example if you set a mix of -100%, than whenever you move the stick, it will always subtract the same amount from it, so it will remain at 0. p.s. However I've noticed, that if you add another mix, and make for ex. CH1 follow exactly CH2, (a mix of 100%) it will not do so! (will not stay at 0) Actually it will follow CH2's stick movement.
I was thinking two Servos to a Y lead to one Chanel on the Receiver. Rotating the nob would give it lots more persise You do lay things out in a way that is understandable, thanks.
Hello Andrew, I have been watching your videos on the building and adapting the Phoenix 2000, with most interest. I am in the process of buying either a Phoenix 2000 or ASW-28 and on your video I have seen that you are using a "Flysky FS-i6" (the same transmitter that I have in my possession), Can you please help me to set up the transmitter to these gliders (the functions must be the same for both) and especially the set up of the flaps. Do you run the servo's simultaneously via two cables ending up to one going to the receiver or are the two servo's connected to two different channels? Thanks for y our help, Emiel Driessen.
I use Taranis radios and OpenTX mostly. The man to ask is Allen Moore of NoobieRC, he is the Phoenix 2000 and FSi6 expert ua-cam.com/channels/xp23yC005hanSysA4vodQA.html
Good morning Andrew, Thank you for your reaction, very much appreciated. Unfortunately your reference to Allen Moore of NoobieRC does not work. Nevertheless I got answers to all my questions from you anyway, through your You Tube movies/explanations because when further surfing on You Tube I found videos made by you on 18 December 2016; 1. FS-i6 Programming. 2. FS-i6 Flapperon 3 methods. They are christal clear and thanks to your good work and the time spent by you, I will be able to program my Flysky FS-i6. Regards, Emiel Driessen
Those knobs do not come with center position do they? Just saw it doesn't... The idea of adding offset to them as to one only goes up and the other only goes down and if you turn it all the way it turns that mix off. Great. You know... Gliding life lol
Hi again ☺️ I was trying to set up my ailerons into flapperons and i could not get it to work . Is it because my left and right servo wires come together with a (Y) and plug into the #1 on reciver? ..... to make it work does each servo need to plug into a different channel? ... if you get some time I could use some help . I gave it my best for 3 hours today . I was trying to put them in the ( C ) switch 1,2,3 .... I followed your other video and I got the motor safe on ( A ) and the dual rate sport mode on ( B ) and training/student on ( D ) switch. Those 3 work perfectly. I just can't get the flaperons to work . And I'm doing it on a FS-i6 mod to 10 channels . The reciver is FS-iA6B ....do I need a 10 channel reciver? I really enjoy your videos , thank you
i like the first method with the variometer thing but if your concern in not been able to find the neutral position easy, why not just use a dead zone on the curves like you did for the throttle?
Thanks Andrew your how to videos are some of the best and easiest to follow. Couldn't get my head around this kind of thing without help. The Engrish manual doesn't make it any easier. lol PS. Congratulations on 10 00 I'm not surprised realy such good videos and useful to information.
I'm wondering what is more effective in slowing down a Sky Surfer? flaperons? or Spoilerons? what is more effective and gives a better overall flying experience? any insight you can give Andrew based on your experience is greatly appreciated!
Dual rates and expo are affecting channel 1. With ailerons on separate channels and mixing, channel 6 is mirroring channel 1. That way, all effects of dual rates and expo on channel 1 (1st aileron servo) are being repeated on channel 6 (2nd aileron servo). So flaperons and dual rates should work together. Am I missing something here?
@@AndrewNewton thanks for the reply. I don't have a plane to try it on. I've inly checked the display option in settings, where it seemed working fine. Also used i6x with latest firmware(I think). Maybe it was i6 or firmware issue.
Thank you so so much, this really helped! For some reason my switch c when set on position 3, kicks in the motor, i checked every setting but not able to shut that down form the switch C. I have set the flaps to 1 position switch D for now on my Efxtra. Cheers!
In Switch assign i have 3 options - Fly mode, Idle mode, Thro. Hold. Fly mode set on switch A - normal/sport. Idle mode set to switch B, and throttle hold = off, for some reason the 'Switch C' does not shop up in switch assign as an option, i can only select Switches A, B & D for the 3 parameters. Wonder if its a software bug
You're right about the C switch not appearing, mine is the same. C must be in a mix maybe? Does anything happen in the Display screen when you switch C?
Yes, when the C switch is all the way down to position 3, on the display the throttle goes exactly midway 30% That means by default the C switch's 3 position is set on 50% throttle. I have this since the day i got this transmitter and haven't been able to resolve this problem
ok i figured it out, the swich C pos 3 was set to 50% throttle under 'Throttle Curve' i simply changed that to 0% when the swich C is on position 3, Now i have working 2 position flaps. :) Last thing is, when on position 3 the ailerons do not work however they work on position 2 (while the flaperons are activated) is this the same with you ? Thanks again
thank you. so. much. I am making the RB-8 (My own plane) and its the first one. im almost done and this helped alot. also, You're so close to 40k!!! congrats!
Andrew, you are SO AWESOME!!! Thank you SO MUCH! One thing, though, mate....I don't understand why you say (in your comments section above) why dual rates AND flaperons are not possible. Mine both work great. I separated the leads like you said, so right aileron goes on ch6 and left on ch 1 (with no y lead). I have the exact same radio, too. ??? Could I possibly be running on different firmware? (I'm running version 1.1 from March 2015)
Thanks Bill. I think it was something like the dual rates only working on Ch1 and not passing through the mix to Ch6. I'd have to recheck it. Don't often use that radio
After watching this video while setting up my first 4 channel foam board plane I got to thinking, is it possible to set up a aux switch or program a duel rate so with a flick of the switch at a set hight range it will slowly bring you in for a landing while only having to use the rudder or the throttle? Without having a gyro/stableizer
Thanks for that! I programmed all the mixes but flicking on flaperon mode causes a massive nose dive...I can’t add another slave to compensate the dive with up-elevator...any idea what to do?
Andrew, main problem with i6 and flaperons is that if you want to have dualrates or expo you are screwed. Mix1 takes raw input from ch1 and sends to ch6, no rates/expo settings applied. the only way to adjust throws remains endpoints. If you know a workaround for that let me know please:)
Thanks for the info , that has helped me out no end , unfortunately I cant do it with the receiver I'm currently using tho (the one supplied with the transmitter) as I have a flight stabilizer installed , I have a spare variometer , but no spare slot for the separate aileron servo ..........looks like I'll need a 9 channel receiver ?
hi. on my plane (volantex phoenix 2000), the left and right aileron servo are connected together in a Y cable and connected to CH1 (since both servos are oriented with the servo arms pointing to the tip, they are acting in the opposite direction as they should). how can i add flaperons with my configuration (your setup in the video has each aileron servo on a separate channel) - when i try to do it via your method 2 in this video, my ailerons dont do an "offset" (lowered flaps) - they are always acting against each other. thanks
i found your i6 crow/butterfly mix tutorial (ua-cam.com/video/q953NjiB6uA/v-deo.html). i connected one aileron directly to a Channel of my receiver (so the Y lead wont be used anymore).
Thank you I have been surching for 3 hours on how to do this but they are all using the dx8 And I was using a flysky sf-t6 so it was really the same agen thanks a lot
Great video Andrew, I have the i6x, and have found a really annoying flaw (Flysky software designers whoopsie moment) in that switch assignments are global for all models, there is no way to configure switches to different assignments on different models...! A real wtf to flysky on that one, it has the potential to be such a great radio, just let down by a hungover software designer. Anyway, flaperons are great, much better than cutting flaps into unequipped wings.
Well, I updated the firmware to 1.0.38.1413 and guess what..they fixed it! One thing though, despite the 'successful update', the version number displayed in the menu has not changed, and it only displays the first two numbers with a date.. i guess they could do a version update update.. At least it is a painless smooth process. Thanks for spurring me into it.
Hello AndrewI am having some problems with turnigy 9xr I bought 3 of them 3 years ago from hobbyking. 2 of them still in their boxes. Recently I noticed that the limits tends to drift ( if that's the word ) so instead of being 0.0 the Alieron Elevator and Rudder seem to self adjust sometimes -34.6 for Alieron 5.6 for elevator -1.2 for rudder. Sorry I hope I have not confused you. What do you think could be at fault? could it be I may have to replace my gimbals. Anyway I opened the other Turnigy 9xr and checked it to find that the throttle when all the way down is not down because timer is counting down and when I apply down pressure on the throttle stick it stops the timer. So out of 3 turnigy 9xr radios I only have one that works.
Yes even after I recalibrate it does the same thing. I am using frsky DJT telemetry in my radio and frsky D8R-11plus as receiver. I don't know if gimbals could cause it. Maybe I could send radio to you if ok? I am scared to go on using it just incase.
Keith, it's not a problem I have encountered before so I wouldn't know how to fix it. All I can suggest is updating the firmware and maybe replacing the gimbals if you can find them. Not much else you can do.
thanks Andrew. I put it away and stick with the flysky fs-i6 much easier to operate and works great. its pity have a few frsky D8R-11plus receivers and frsky DJT Telemetry radio modules.
I don't understand....how do you manage to control both the servos down if your using a Y-connector on both of your servos? The signal would be the same on both servos because it only has one cable from the rx....unless you connected the servos on two separate channels...
Thanks andrew.... you have given me an idea of how to slow down my 2 planes in landing. Actually I was really thinking of it due to I was flying it in a not so large area and I have to descent maybe 20ft. then have to catch it on landing.... the DW eagles 1200 wingspan and the MG800. The eagle is ok but I want it more slower on descent but the MG800 is a little bit agile and descent from 20ft. for about 20 to 30meters away from you is still a little bit tricky to slowdown then able to catch it....
Hey Andrew, I've tried your method on my FlySky i6-X and only seem to get the vario able to make one aileron go up and the other down. I copied everything exactly and this has me stumped! If I knew what the pos and neg mix did and how the master and slave interacted, I might be able to figure it out :( As it stands, I'm sort of lost.
If the ailerons are working correctly and on separate channels, all you have to do is change the flaperon mix weight values from - to + for the offending flaperon (or + to -)
@@AndrewNewton thanks! The more I played around with the settings while sitting on the lounge with my superEZ on the coffee table, the better I understood how the programming works.. the first time round I was using a y lead and of course, it didn't work lol. I separated the servos on channel 1 and 5 and now I'm set. Ive got some mild camber, but because this plane is already so light and floaty, I feel it was a bit pointless. GREAT learning experience, tho. As a side note, what are the rules for us hobbyists popping out to a wide open field during the Coronapocalypse? No go? Or go but be careful? Take care, Andrew and I look forward to the next video. Thanks so much for your fast reply, too.
Hi M. Newton, I have a nano talon and installed skies on it, I can controlled it nicely with a ski at the back plug on my channel 6, my problem is it is difficult to lift, I was wondering if I can assign my switch D to control the flaperons, but I’m using kopilot so is it possible to program it thank you and have a nice day
@@AndrewNewton Thank you for your respond, what would be a autopilot like kopilot that I can use the plaperons with it, if you can propose me one, easy and something not to complicated 😂 have a nice evening and thanks again for your information.
Hi Andrew have followed your info on the flapperon setup but I have tried to relate this to a NX3 flight contoller with the 3 position SW3 operates the function of the unit. Have exactley the same equipment as you and have followed your instructions. Please help (74 yr old oap) Colin
How to make the alieron and elevator mix ? For example when I turn left and right with the alieron I want the elavtor to move up aswell . instead when I turn to one side the elevator goes down and when I turn to the other side it goes up . how to make the elevator stay up when I turn both sides?
Hello Andrew. I need help for biding FS-i6 transmitter, with Nighthawk M-16 receiver. I try it the same biding with FS-iA6 receiver but doesn't work. Can you help me? Thanks.
Hello Andrew. I have an FS-i6 transmitter and work normally with an FS-iA6 receiver but don't bind the Nighthawk M-16 receiver. The transmitter isn't compatible with this receiver? Can you help me?
@@AndrewNewton Yes, I have a Flysky receiver and FS i6 transmitter and working normally on the binding. But the bind on the Nighthawk M-16 receiver doesn't work. Can you help me for binding this receiver with the FS transmitter? Thanks for the help.
I have the same Transmitter i use for my racing quads, iv decided to give fixed wings a go reptile s800, win wing z-84 and a rainbow 800mm, do you have a video on how to set up this transmitter for fixed wings? cheers
Don't know, I would have to do a "black-box" input and output state assessment and infer what went on inside the "black box" from that. I expect it would mean adding a hypothetical feedback system that stopped runaway conditions.
Andrew, thanks for that mate. Really helped me set up my easystar ailerons. Took me a while to understand what the pos and neg mix referred to and also understanding the offset. New stuff to me. Do you have a vid on understanding the basic terminology, I'm 49, you think I should know this by now lol. Thanks from the UK.
@@AndrewNewton thanks anyway. You clearly have a good setup there looking at all the planes in the background to your vids. Where are you in the world..Oz?
Cool, Thanx for all the informative vids. Fordingbridge, Hampshire. UK. Not quite Australia but it will do, the wildest animals we have here are ponies 😆!!!!
Switch aileron rates with the Fly Mode switch. Normal or Sport can be setup with any rates and expo. What do you mean by 7? There is no Ch7 on this radio.
Probably came upon both this excellent tutorial and the RC hobby a bit late on the brain deterioration curve. But if I decide to try anything more than RTF cheapies it'll be nice to not have to add the vagaries of an indecipherable accent to the results of a lifetime of operating heavy machinery. ;-)
HI Andrew firstly I follow you all the time brilliant videos all the best keeping this hobby exciting daily. Just wanted to ask if you have or you could do a video showing the same functions on a taranis x7 cause this was hard to follow. I really wanna add flaps into my flying on a 4 channel thanks again ...
Many thanks, yes I have done OpenTX flaps and flaperons (same for all OTX radios). Check out the playlist - OpenTX and Taranis - ua-cam.com/play/PLC8MdCMvxwBh_Pkp1EkLilgWcK8CQINd9.html
thanks andrew for the quick response checked out the video was really helpful. forgot to ask does do u have to have separate channel for each servo or can I program it with y cable?
oh right gotcha , but say for an example you use separate channels for ailerons alone, and somehow program the mix; the pos mix and neg mix to something that wont require the servos to be mounted in a certain way to have ailerons? is that possible on this transmitter, cuz ik it is on the spektrums
Similar but different. Flaperons are aileron that are also used as flaps (when you don't have separate flaps) Elevons are Ailerons that are also used as elevators (like on a flying wing)
I just bought the FLYSKY I6X , setup is exactly the same as you describe , except the I6X allows you to assign switches as a channel , which actually makes the setup a little easier , but works so well on my 1.8 meter Piper Cub :) , Cheers Andrew !
I could use some help setting mine up . I tried for 3 hours today . I have the FS-i6 but mod to 10 channels so it's like the FS-i6x .... I'm trying to put the flaperons on ( C )switch 1,2,3 the other 3 are taken . And I don't want it on the sliders dials . Not sure you will even see this comment. But I thought I would try to reach out , you made it sound easy . Much respect 👏
Thanks Andrew for all the info you share, it has been really helpful to me and thousands of other people.
You explain everything clearly.
Great job
Cheers
Brian NZ
Thanks Brian, glad it's understandable.
A great 'public' service this was! I just finished setting up my Flaperons and they work perfectly - thank you sir!
Excellent, thanks for letting me know
Thank you very much for that Andrew! Just what I needed to set up my SU26
Thanks for making things easy. Very clear and concise solution to a frustrating problem, thanks again !!
Thanks for the feedback, I do strive keep it clear and simple
I'm a new to RC plane, and your videos has taught me a lot! Thank you!
Great to hear!
Hey Andrew, thank you so much for this video.
Ive been looking to set flaperons on my new Hobbyking EZIO but couldnt get it to program to a switch.
Thanks to you i've now been able to do it.
Cheers mate!
Excellent, glad the video helped
I realize I needed mix 3 for the servo on channel 5 but that doesn't change what happened. When I wrote potentiometer 1 I meant potentiometer A. It seemed that as soon as I adjusted the positive and negative that's when trouble started. I want to use the potentiometer but have just 1 battery left and am reluctant to attempt that program again. I think you owe me a battery. Best of spirits!
It's not the mix causing problems Brian. I'll bet you have a dodgy servo, battery or connection.
You could try again with a 4xAA rechargeable battery pack plugged straight into the receiver.
The UBEC provides no ground from batt to Rx but then neither would the average 4AA pack. The battery is an eflite. Quality pack. UBEC is generic but had no problems until I wanted to use the program you provided for potentiometer use. I purchased two new packs but don't want those fried too.
As you are the only one having such issues I am convinced you have faulty connections or equipment. Check everything again
I have a 2s 120mah 20c into a 5v ubec then onto the FS I-6 Reciever I successfully connected a servo to channel 1 with the first mix being 5 slaved and another servo to 5. I had servo function then I added mix two with potentiometer 1 with channel 1 slaved to that I adjusted the potentiometer and only one servo moved I started to adjust positive and negative to find control for both servos from the potentiometer and the servos started sizzling, trembling and going all over the place. I removed the potentiometer from the mix. After that I found that there was no servo response at all. Re binded the Rx and nothing still. Thought battery was dead and plugged it into the charger. Error response from charger. Looked at battery and noticed it had ballooned a little. Plugged in another battery and Rx and servos are ok. That program you instructed on using the potentiometer for flaperon mixing fried one of my batteries!
thanks Andrew......had my fsi6 for a while and never got around to using mixes ...
now when i need them i can check out your vids for an easy tutorial ...and congrats on the 10 k .
Thanks David, mix it up
Thank you. I opted this route rather than adding flaps to my motor glider!!!
Glad it helped!
Hmmmmhhhh.....I don´t understand how it works......
And where do You connect the servos ???
This vid is just what I looked for !
I`m just assembling a new Multiplex indoor funnycub, and it needs just those flaperons.
Thank You very much !
ACE !!!!
MANY MANY THANK YOU'S !!!!
was looking for an easy solution to having flap function with just ailerons for ages :)
and video so easy to follow.
keep up the great informational vids ( esp for the FS-i6 )
CHEERS !!
No problem. Let me know of any other programming you would like to see.
Excellent video! I have the FlySky i6 TX and was hoping to be able to add flaperons without buying a new transmitter👍
Glad I could help
Hi Andrew. I must say that your channel is great, informative and helpfull. I have started to fly RC planes in about half a year ago and learnd a lot from your channel. I have just finished to build Photon from from ExperimentalAirlines by Ed, and as I have FlySky i6 I really like your tutorial how to set Flaperons, which I want to use. Here comes the problem. I have two separate servos plugged in to channel 1 and channel 6 is right aileron. I have settup the radio the same way as you describe. It works... "but" my ailerons are reversed. You mentioned in the video that we should change positive and negative mix to either 100% or -100%. Ailerons are wokring in the separate direction as they should when I set 100%, but reversed. If I choose -100 on positive mix both are up and for my understanding negative mix left aileron should go down, but id does not. If I have both mixes on mix#1 on -100 both ailerons go up. But if I have 100% it works but reversed. Can you please help me to figure out the problem? My goal is to use separate leads for servos, and have flaperons for soaring. I would really appriciate any help and any advice. Thank you in advance. :)
Hi Martin. Photon was my first plane too. I would start from the beginning with your mixing. Just plug in the L aileron to Ch1 and get it working in the correct direction. Select Reverse for Ch1 if it's working in the wrong direction. Then my instructions should work for you. Good luck.
Hi Andrew, I must say that your answer kind of helped. :) I got it working eventualy, just had to set up new plane on the radio and start from CH1, put it to revers, played with it for about 20 min and got it working :D juhuu :) Now just waiting for a windless day to maiden it. Thank you anyway :)
Hi Andrew, being a man of immense RC knowledge, can you answer a question for me? I would like to program Flaperons on a Volantex G2 but I have a BGL-6G-AP GPS Flight Stabiliser on board. As the Ailerons have to be split using Ch's 1 & 6 on my FlySky I6 Controller, is there anyway around this as the FC gets the Aileron commands from Ch 1 on the controller and uses a Y cable? What do you think?.....Best regards, Pete
Not possible with the BGL I'm afraid
@@AndrewNewton Thanks Andrew, yer that's what I thought. Shame really cos you can't have GPS/RTH for FPV & Flaperons. That will be something for the FC Manufacturers to think about, it could be done with an extra FC Ch. :) Happy Flying, regards, Pete
Pretty easy to understand the case when you mix a channel into itself.
The radio executes commands in sequence, like a flowchart.
1. take the value of CH2
2. modify it by the amount given in the mix
3. write it back to CH2
4. output the final value to CH2's port, or display it, or whatever
5. goto 1.
For example if you set a mix of -100%, than whenever you move the stick, it will always subtract the same amount from it, so it will remain at 0.
p.s. However I've noticed, that if you add another mix, and make for ex. CH1 follow
exactly CH2, (a mix of 100%) it will not do so! (will not stay at 0) Actually it will follow CH2's stick movement.
Thanks, that makes sense.
Thanks mate, great advice got this tx this year big help nice 1 🤙
Really nice video Andrew, was considering this as my first radio and I think you've just sold me....
It's still the best first radio (and beyond)
I was thinking two Servos to a Y lead to one Chanel on the Receiver. Rotating the nob would give it lots more persise You do lay things out in a way that is understandable, thanks.
OK for flaps, but you need separate channels for flaperons
@@AndrewNewton Programming flaps would free up my now yous'd channel sweet.
Brillant, all your videos are well thought out and understandable!
Thanks Tony. That is my aim
Thank you very much. In my opinon one of cleaest explations on you tube. I have been trying to set up my Redina D.L.G
Thanks Gavin
Hello Andrew, I have been watching your videos on the building and adapting the Phoenix 2000, with most interest.
I am in the process of buying either a Phoenix 2000 or ASW-28 and on your video I have seen that you are using a "Flysky FS-i6" (the same transmitter that I have in my possession),
Can you please help me to set up the transmitter to these gliders (the functions must be the same for both) and especially the set up of the flaps. Do you run the servo's simultaneously via two cables ending up to one going to the receiver or are the two servo's connected to two different channels? Thanks for y our help, Emiel Driessen.
I use Taranis radios and OpenTX mostly. The man to ask is Allen Moore of NoobieRC, he is the Phoenix 2000 and FSi6 expert ua-cam.com/channels/xp23yC005hanSysA4vodQA.html
Good morning Andrew,
Thank you for your reaction, very much appreciated. Unfortunately your reference to Allen Moore of NoobieRC does not work.
Nevertheless I got answers to all my questions from you anyway, through your You Tube movies/explanations because when further surfing on You Tube I found videos made by you on 18 December 2016;
1. FS-i6 Programming.
2. FS-i6 Flapperon 3 methods.
They are christal clear and thanks to your good work and the time spent by you, I will be able to program my Flysky FS-i6.
Regards,
Emiel Driessen
Another great video, well done 👏 thank you 😊
Those knobs do not come with center position do they? Just saw it doesn't... The idea of adding offset to them as to one only goes up and the other only goes down and if you turn it all the way it turns that mix off. Great. You know... Gliding life lol
Very informative video. Many thanks for sharing. BTW, would you recomend this FlySKY RC trasmitter ? TIA
Yes, best cheap programmable radio. But if you can afford a little more I would recommend the Taranis QX7
@@AndrewNewton Great. Will check if we can get Taranis in England
Hi again ☺️ I was trying to set up my ailerons into flapperons and i could not get it to work . Is it because my left and right servo wires come together with a (Y) and plug into the #1 on reciver? ..... to make it work does each servo need to plug into a different channel? ... if you get some time I could use some help . I gave it my best for 3 hours today . I was trying to put them in the ( C ) switch 1,2,3 .... I followed your other video and I got the motor safe on ( A ) and the dual rate sport mode on ( B ) and training/student on ( D ) switch. Those 3 work perfectly. I just can't get the flaperons to work . And I'm doing it on a FS-i6 mod to 10 channels . The reciver is FS-iA6B ....do I need a 10 channel reciver? I really enjoy your videos , thank you
Yes you need separate channels for each aileron for flaperon mix
@@AndrewNewton Thank you 😊
i like the first method with the variometer thing but if your concern in not been able to find the neutral position easy, why not just use a dead zone on the curves like you did for the throttle?
I meant to say variable resister rather than variometer. Dont think curves are available for that
great tutorial, thanks! do you know if It is possible to mix in some elevator trim (pitch up) when flaperons are deployed? regards.
Insufficient mixes for that unfortunately
@@AndrewNewton thanks for the reply! 👍👍
Thanks Andrew your how to videos are some of the best and easiest to follow.
Couldn't get my head around this kind of thing without help.
The Engrish manual doesn't make it any easier. lol
PS. Congratulations on 10 00 I'm not surprised realy such good videos and useful to information.
You're right about the dodgy manuals these days. I still find OpenTX way more logical than this but it's fun learning
Andrew Newton if I buy a pnf plane that needs a DX transmitter can I use the flysky i6 or will I need to change the receiver to flysky
DX is Spektrum I think, you would need to change the receiver to use your radio
thanks
I'm wondering what is more effective in slowing down a Sky Surfer? flaperons? or Spoilerons? what is more effective and gives a better overall flying experience? any insight you can give Andrew based on your experience is greatly appreciated!
Flaperons for shorter takeoff and slower flying but more lift, Spoilerons for shorter landing and less lift (specially for slope soaring)
@@AndrewNewton Im in Florida USA so not much slope soaring here. I will do the Spoilerons for shorter landings. THANK YOU!
Hi Andrew.....Do you think that a similar protocol would work with Taranis for creating mixes for flaperons and spolierons
Here's how to do it in OpenTX - ua-cam.com/video/zzv77R1efes/v-deo.html
Dual rates and expo are affecting channel 1. With ailerons on separate channels and mixing, channel 6 is mirroring channel 1.
That way, all effects of dual rates and expo on channel 1 (1st aileron servo) are being repeated on channel 6 (2nd aileron servo).
So flaperons and dual rates should work together.
Am I missing something here?
I seem to recall some problem with the mix on Ch1 not being passed on to Ch6
@@AndrewNewton thanks for the reply. I don't have a plane to try it on. I've inly checked the display option in settings, where it seemed working fine. Also used i6x with latest firmware(I think). Maybe it was i6 or firmware issue.
Thank you so so much, this really helped! For some reason my switch c when set on position 3, kicks in the motor, i checked every setting but not able to shut that down form the switch C. I have set the flaps to 1 position switch D for now on my Efxtra. Cheers!
Is switch C assigned to any function in the Switch Assign screen, like throttle hold or idle?
In Switch assign i have 3 options - Fly mode, Idle mode, Thro. Hold. Fly mode set on switch A - normal/sport. Idle mode set to switch B, and throttle hold = off, for some reason the 'Switch C' does not shop up in switch assign as an option, i can only select Switches A, B & D for the 3 parameters.
Wonder if its a software bug
You're right about the C switch not appearing, mine is the same. C must be in a mix maybe? Does anything happen in the Display screen when you switch C?
Yes, when the C switch is all the way down to position 3, on the display the throttle goes exactly midway 30% That means by default the C switch's 3 position is set on 50% throttle. I have this since the day i got this transmitter and haven't been able to resolve this problem
ok i figured it out, the swich C pos 3 was set to 50% throttle under 'Throttle Curve' i simply changed that to 0% when the swich C is on position 3, Now i have working 2 position flaps. :) Last thing is, when on position 3 the ailerons do not work however they work on position 2 (while the flaperons are activated) is this the same with you ? Thanks again
thank you. so. much. I am making the RB-8 (My own plane) and its the first one. im almost done and this helped alot. also, You're so close to 40k!!! congrats!
Thanks Rapid. Great to hear the video helped
Have you done a AT10 II 12 channel Transmiter, If would you be willing to do so?
Thanks
Pat.
Haven't looked at the Radiolink. If they wanted to send one for review I'd look at it.
Thank you so much !Great Job Manfred (Austria)
Sweet Manfred.
What if you have separate flaperons like on the eflite timber while using the FS-i6x
I think you mean flaps? ua-cam.com/video/xt5IdeLdiug/v-deo.html
Thanks once again, will add #2 to my setup. And by the way congrats for 10k!
Glad it helped, and many thanks for noticing the 10K
i also added #2
Andrew, you are SO AWESOME!!! Thank you SO MUCH!
One thing, though, mate....I don't understand why you say (in your comments section above) why dual rates AND flaperons are not possible. Mine both work great. I separated the leads like you said, so right aileron goes on ch6 and left on ch 1 (with no y lead). I have the exact same radio, too. ??? Could I possibly be running on different firmware? (I'm running version 1.1 from March 2015)
Thanks Bill. I think it was something like the dual rates only working on Ch1 and not passing through the mix to Ch6. I'd have to recheck it. Don't often use that radio
After watching this video while setting up my first 4 channel foam board plane I got to thinking, is it possible to set up a aux switch or program a duel rate so with a flick of the switch at a set hight range it will slowly bring you in for a landing while only having to use the rudder or the throttle? Without having a gyro/stableizer
Nice idea but this radio might be a bit too limited. Would be easy with Taranis and OpenTX
Thanks for that! I programmed all the mixes but flicking on flaperon mode causes a massive nose dive...I can’t add another slave to compensate the dive with up-elevator...any idea what to do?
Use less flaperon movement and be ready on the elevator stick, or buy a transmitter with more mixes available
Andrew, main problem with i6 and flaperons is that if you want to have dualrates or expo you are screwed. Mix1 takes raw input from ch1 and sends to ch6, no rates/expo settings applied. the only way to adjust throws remains endpoints. If you know a workaround for that let me know please:)
Oh thanks, that explains why my Ch1 and Ch6 limits are slightly different.
Nice now I can setup the FT Bushwacker! Thanks!
Excellent, go to it
I have the same radio. I'm having trouble figuring out the differential throttles for a twin. Have you ever done that ? Great videos, thanks !
No I haven't but iforce2D has.
Thanks for the info , that has helped me out no end , unfortunately I cant do it with the receiver I'm currently using tho (the one supplied with the transmitter) as I have a flight stabilizer installed , I have a spare variometer , but no spare slot for the separate aileron servo ..........looks like I'll need a 9 channel receiver ?
Time to switch to Taranis Q X7
hi. on my plane (volantex phoenix 2000), the left and right aileron servo are connected together in a Y cable and connected to CH1 (since both servos are oriented with the servo arms pointing to the tip, they are acting in the opposite direction as they should).
how can i add flaperons with my configuration (your setup in the video has each aileron servo on a separate channel) - when i try to do it via your method 2 in this video, my ailerons dont do an "offset" (lowered flaps) - they are always acting against each other.
thanks
i found your i6 crow/butterfly mix tutorial (ua-cam.com/video/q953NjiB6uA/v-deo.html). i connected one aileron directly to a Channel of my receiver (so the Y lead wont be used anymore).
@@unclealig Well done. Must have separate channels for the ailerons if you want flaperons
Thank you I have been surching for 3 hours on how to do this but they are all using the dx8
And I was using a flysky sf-t6 so it was really the same agen thanks a lot
My pleasure Davis
How much range it covers? PLEASE Reply...I bought but it loses the control after 100 Meters in my society....
Tell me your experience...
2km in perfect conditions. Which receiver are you using?
@@AndrewNewton Hello I am using FS ia6b..what about it? My transmitter is new from banggood
@@MartialArtLife That's a good receiver, should get much more range than that. Check for broken antenna
ua-cam.com/video/KZaE1qEnIWs/v-deo.html
Great video Andrew, I have the i6x, and have found a really annoying flaw (Flysky software designers whoopsie moment) in that switch assignments are global for all models, there is no way to configure switches to different assignments on different models...! A real wtf to flysky on that one, it has the potential to be such a great radio, just let down by a hungover software designer.
Anyway, flaperons are great, much better than cutting flaps into unequipped wings.
On te i6 switch assignments are unique to each model, but if it's not how the i6x works that's crazy.
It is first run i6x, firmware 1.0 01-jul-2016, I only hope they fix it with a future upgrade, else it becomes another junkbox radio.
Well, I updated the firmware to 1.0.38.1413 and guess what..they fixed it! One thing though, despite the 'successful update', the version number displayed in the menu has not changed, and it only displays the first two numbers with a date.. i guess they could do a version update update..
At least it is a painless smooth process. Thanks for spurring me into it.
Hello, great video!! Thank you Very much!! Can you tell me if I can use a 3.7 v lipo battery for the receiver? What battery do you use?
I use 5V supplied by the ESC or BEC, or 4 x AAA NiMH pack. 3.7V is not enough. Check the specs of your receiver for the voltage range
On flysky 1s will work no problem
@@peterzingler6221 Perfect ! thanks !!! I´ll use 1 s
Is it possible to programme flaps when ailerons are on a Y lead on one channel? Sorry if that’s a daft question!!
Not possible.
@@AndrewNewton thanks. Thought as much. I’ll separate them on the Conscendo. Cheers.
amazing.
Hello AndrewI am having some problems with turnigy 9xr I bought 3 of them 3 years ago from hobbyking. 2 of them still in their boxes. Recently I noticed that the limits tends to drift ( if that's the word ) so instead of being 0.0 the Alieron Elevator and Rudder seem to self adjust sometimes -34.6 for Alieron 5.6 for elevator -1.2 for rudder. Sorry I hope I have not confused you. What do you think could be at fault? could it be I may have to replace my gimbals. Anyway I opened the other Turnigy 9xr and checked it to find that the throttle when all the way down is not down because timer is counting down and when I apply down pressure on the throttle stick it stops the timer. So out of 3 turnigy 9xr radios I only have one that works.
Why they would drift I don't know but you could recalibrate the radio (If you're using OpenTX) Page 9 in Radio setup
Yes even after I recalibrate it does the same thing. I am using frsky DJT telemetry in my radio and frsky D8R-11plus as receiver. I don't know if gimbals could cause it. Maybe I could send radio to you if ok? I am scared to go on using it just incase.
Keith, it's not a problem I have encountered before so I wouldn't know how to fix it. All I can suggest is updating the firmware and maybe replacing the gimbals if you can find them. Not much else you can do.
thanks Andrew. I put it away and stick with the flysky fs-i6 much easier to operate and works great. its pity have a few frsky D8R-11plus receivers and frsky DJT Telemetry radio modules.
I don't understand....how do you manage to control both the servos down if your using a Y-connector on both of your servos? The signal would be the same on both servos because it only has one cable from the rx....unless you connected the servos on two separate channels...
You are correct. Must have separate channels
Thanks andrew.... you have given me an idea of how to slow down my 2 planes in landing. Actually I was really thinking of it due to I was flying it in a not so large area and I have to descent maybe 20ft. then have to catch it on landing.... the DW eagles 1200 wingspan and the MG800. The eagle is ok but I want it more slower on descent but the MG800 is a little bit agile and descent from 20ft. for about 20 to 30meters away from you is still a little bit tricky to slowdown then able to catch it....
Hey Andrew, I've tried your method on my FlySky i6-X and only seem to get the vario able to make one aileron go up and the other down. I copied everything exactly and this has me stumped! If I knew what the pos and neg mix did and how the master and slave interacted, I might be able to figure it out :( As it stands, I'm sort of lost.
If the ailerons are working correctly and on separate channels, all you have to do is change the flaperon mix weight values from - to + for the offending flaperon (or + to -)
@@AndrewNewton thanks! The more I played around with the settings while sitting on the lounge with my superEZ on the coffee table, the better I understood how the programming works.. the first time round I was using a y lead and of course, it didn't work lol.
I separated the servos on channel 1 and 5 and now I'm set. Ive got some mild camber, but because this plane is already so light and floaty, I feel it was a bit pointless.
GREAT learning experience, tho.
As a side note, what are the rules for us hobbyists popping out to a wide open field during the Coronapocalypse? No go? Or go but be careful?
Take care, Andrew and I look forward to the next video. Thanks so much for your fast reply, too.
Excellent Nick, glad you worked it out. No go is the message from the experts. Stay home. Doubt I will be flying for a long time.
@@AndrewNewton seems appropriate. I'd love lots of talking head videos sharing stories about flying and life in general.
So glad I found your channel.
Hi M. Newton, I have a nano talon and installed skies on it, I can controlled it nicely with a ski at the back plug on my channel 6, my problem is it is difficult to lift, I was wondering if I can assign my switch D to control the flaperons, but I’m using kopilot so is it possible to program it thank you and have a nice day
No programming with the Kopilot unfortunately.
@@AndrewNewton Thank you for your respond, what would be a autopilot like kopilot that I can use the plaperons with it, if you can propose me one, easy and something not to complicated 😂 have a nice evening and thanks again for your information.
Matek boards using INAV are the best but not simple at all. I don't know of anything in between sorry
Muito bem explicado 'parabéns
Very nice man
You are AMAZING! Thank you very much!
Thanks Nathan, glad to help
Hi Andrew have followed your info on the flapperon setup but I have tried to relate this to a NX3 flight contoller with the 3 position SW3 operates the function of the unit. Have exactley the same equipment as you and have followed your instructions. Please help (74 yr old oap) Colin
Hi Sonja, I don't know that FCB but I doubt that the firmware supports flaps
How to make the alieron and elevator mix ? For example when I turn left and right with the alieron I want the elavtor to move up aswell . instead when I turn to one side the elevator goes down and when I turn to the other side it goes up . how to make the elevator stay up when I turn both sides?
Not possible with this radio
@@AndrewNewton thanks I figured that . only way to do so is gyro right ? I was try to make my own stabilization mix
Would you know, if I may turn the mix on/off via one of the switches?
Not possible with this radio
that helped a lot thanks ^^
Hello Andrew. I need help for biding FS-i6 transmitter, with Nighthawk M-16 receiver. I try it the same biding with FS-iA6 receiver but doesn't work. Can you help me? Thanks.
Does it have a Flysky receiver?
Hello Andrew. I have an FS-i6 transmitter and work normally with an FS-iA6 receiver but don't bind the Nighthawk M-16 receiver. The transmitter isn't compatible with this receiver? Can you help me?
@@AndrewNewton Yes, I have a Flysky receiver and FS i6 transmitter and working normally on the binding. But the bind on the Nighthawk M-16 receiver doesn't work. Can you help me for binding this receiver with the FS transmitter? Thanks for the help.
@@aurelbarbor1125 No I cant help
i cannot thank you enough for you help :) :)
Woohoo thank you too
I have the same Transmitter i use for my racing quads, iv decided to give fixed wings a go reptile s800, win wing z-84 and a rainbow 800mm, do you have a video on how to set up this transmitter for fixed wings? cheers
Not something I have done. My mate Allen Moore would be able to help ua-cam.com/channels/xp23yC005hanSysA4vodQA.html
Hi Andrew, how to set a launch mode for a v-tail dlg (newbie on the sport..:-)
Same as flaperons in this video but apply the mix to elevator. But you really need more mixes like with Taranis and OpenTX for a full DLG setup
@@AndrewNewton Great !!! it was so easy, thank you Andrew. !!!
Channel 6 into Channel 6, recursive programming, very neat!
Why doesn't it create a run away feedback loop?
Don't know, I would have to do a "black-box" input and output state assessment and infer what went on inside the "black box" from that. I expect it would mean adding a hypothetical feedback system that stopped runaway conditions.
How can I mix flaperons for dlg?? So you have flaps on rudder, like you had on versus.
I suspect it's not possible with this radio.
@@AndrewNewton sorry on throttle
if I have the airelons plugget in just 1 channel (2 in 1 cable) , Can I do the flaperons?
No, must be on separate channels
Did it like you now, is perfect
Andrew, thanks for that mate. Really helped me set up my easystar ailerons. Took me a while to understand what the pos and neg mix referred to and also understanding the offset. New stuff to me. Do you have a vid on understanding the basic terminology, I'm 49, you think I should know this by now lol. Thanks from the UK.
To be honest I don't understand FlySKY logic very well. I tend to fiddle with numbers until it works the way I want. FrSKY makes more sense to me.
@@AndrewNewton thanks anyway. You clearly have a good setup there looking at all the planes in the background to your vids. Where are you in the world..Oz?
Correct. Geelong Victoria
Cool, Thanx for all the informative vids. Fordingbridge, Hampshire. UK. Not quite Australia but it will do, the wildest animals we have here are ponies 😆!!!!
@@mickelson8332 I'm scared of ponies, they can be nasty
Hi, which is the approximate range for this radio? Thanks
iforce2d has gone 2.3km but maybe 1.5km in normal circumstances
With what material is it coated? Why is the brightness?
Clear packing tape
hello, how can I run the aileron 50% by assigning the roll key to 7? Switch on : 100% | switch off 50%
Switch aileron rates with the Fly Mode switch. Normal or Sport can be setup with any rates and expo. What do you mean by 7? There is no Ch7 on this radio.
@@AndrewNewton For example, I want to assign sport and normal flight mode to switch 1. how can I do that ?
@@cancihancelebi3495 Watch my i6 programming video
Thanks for the video, it works great.
Excellent
10kkkkk!!! Congrats are in order!
Thanks for contributing Roberto
Thenks
Can you mix flaperons with elevator?
Not enough mixes I suspect
@@AndrewNewton well... People have been adding the open tx to it to fix that. Us glider flying folks love some mixes lol
Hello Brother.
I did it the way it was in the video, but mine keeps moving backwards
Change to negative weight in the mix
Can you do elevons in the same way?
Yes, it all has a preset elevon mix
Probably came upon both this excellent tutorial and the RC hobby a bit late on the brain deterioration curve. But if I decide to try anything more than RTF cheapies it'll be nice to not have to add the vagaries of an indecipherable accent to the results of a lifetime of operating heavy machinery. ;-)
Haha, happy to help a fellow ageing Aussie
so I can set up the butterfly system on a glider?
I think so. Maybe ask Allen, Noobie RC - ua-cam.com/channels/xp23yC005hanSysA4vodQA.html
HI Andrew firstly I follow you all the time brilliant videos all the best keeping this hobby exciting daily. Just wanted to ask if you have or you could do a video showing the same functions on a taranis x7 cause this was hard to follow. I really wanna add flaps into my flying on a 4 channel
thanks again ...
Many thanks, yes I have done OpenTX flaps and flaperons (same for all OTX radios). Check out the playlist - OpenTX and Taranis - ua-cam.com/play/PLC8MdCMvxwBh_Pkp1EkLilgWcK8CQINd9.html
thanks andrew for the quick response checked out the video was really helpful. forgot to ask does do u have to have separate channel for each servo or can I program it with y cable?
For flaps you can use a Y lead, but flaperons must be on separate channels
is there a dual aileron mode? or will i have to buy a y cable?
For flaperons you need ailerons on separate channels, for just ailerons you can use a Y lead in one channel
oh right gotcha , but say for an example you use separate channels for ailerons alone, and somehow program the mix; the pos mix and neg mix to something that wont require the servos to be mounted in a certain way to have ailerons? is that possible on this transmitter, cuz ik it is on the spektrums
Yes you can make them go either way in the mixing or channel reversing
Can i use spoiler ons with elevons to take off with them both going upwards
What plane?
Piper j3 cub balls wood 1.2m wingspan
@@aryamanshukla7248 Flaperons down a bit and elevator up would work
Ok thanks
Can i take off with just elevons or do I have to have flaperons
Are Flaperons the same as Elevons?
Similar but different. Flaperons are aileron that are also used as flaps (when you don't have separate flaps) Elevons are Ailerons that are also used as elevators (like on a flying wing)
Qudacopter f450 naza mlite setup with fs-i6 transmitter setting
Dont know about quads
Thanks ! CAVU
Thanks sir,,, i got it
Welcome 👍
What is vrr and vrb
Variable Resistor A and B (the knobs)
What if left and right Aldrin are plugged into the same channel
Then they will work only as ailerons
Andrew Newton that's a bummer. My wing is already built with the y harness only coming out of the wing
Andrew Newton got it working with just flaperons no spoilers thanks
check out the glider on my channel
Valeu 👍
hi where can I buy that plane ,I am in asia
Hello, you can buy kits from USA www.slopeaerobatics.com/le-fish-and-spindrift-plans/
fsi6x use - expo to make FIXED WING les twitch or +expo
Good question. Negative expo, which is different to most other systems.
@@AndrewNewton so say 100 rates - 35 expo for example
@@jujucattys156 Depends on how much throw that gives but that would be my standard starting setup for most planes
I need help....
Ask Allen Moore Noobie RC - ua-cam.com/channels/xp23yC005hanSysA4vodQA.html
They are called elevons, and nothing else.
Thanks again Peter. Feel free to call out all my blunders. You will be busy!
Thanks andrew! Helped a lot!!!
Good to hear it Hazwan
Thenks