Ok got it. Change both caps to 220uf 10v works great !!! This solves last led being dim, sequence is speeded just a little bit by cap on timer. paly around with the caps to get flash speed you want. Also you can discard the 4007 diode. Works fine without it.
Nice. Your initial cascading circuit reminds me of something I designed on a bar napkin at 2 AM many years ago. My circuit had a different purpose and it was critical that it be integrated with a larger circuit by 8 AM. Fun memories.
احسنت تقسيم التيار كان منتظم ابدعت فى التصميم ولاكن انت انسيت حجه وفيه فكره جديدا ولى هيه التصميم والاطار وبداع فى تقسم الايظاه وهكى المقطع يخد وقت واكثر مشاهده اعجبنى
Ppl really need to get in to small ic I can make one strobe, zig zag, flicker or solid on a board smaller Than that 9v battery and run off 3v . Programmable as well. What I started doing years ago was when I found something that interests me I'd buy two of the items one I took apart and learned from and a lot of times I do have to ask someone who knows, trial and error. The 555 is cool but way to much work to many parts and room taken up. I started with stuff like this and by no means am I kicking it. It's a good learning experience and circuit. But wouldn't you like to build the same or more advanced the size of that 9v and a whole lot less parts? Good job on the circuit and it is important to learn and teach. No disrespect intended.
Interesting component change would be to switch out one of the resistors on the 555 to a variable pot and you can change the speed of the LED's. Say to 50K. experiment a little bit.
@@RusoHacker007 So you are telling me that all those solder joints I made since my first job in 1965 until now are no good? All my employers would not agree with you. Yes, there are times that putting flux on maybe a piece of brass that is not tinned is necessary, but where he is soldering these components together, is OK just to use the solder with flux in it. The components he is soldering are pre-tinned. The flux in the solder is sufficient.
@@vpistilli Sounds good. Didnt mean to upset you. I just found whether the solder has flux or not, using soldering flux makes the solder flow a lot better.
pregunto.... como se puede hacer ese mismo efecto pero de derecha a izquierda y viceversa en un solo circuito y si es posible con control de velocidad...
A mí me duelen las retinas al ver como escribiste "hojos", todos tienen sus defectos, antes de hacer el comentario mejor subí un vídeo explicando cómo utilizar la soldadora y el estaño...
Está mal, en la colocación del diodo rectificador pone en pantalla el signo de positivo en el lado negativo (cátodo). Haz bien el vídeo y sorprende con tu circuito.
Невероятно полезная вещь. Но уж больно громоздкая ёлочная гирлянда. особенно кусачки для ногтей хороши. Для съёмки хоть в долг у кого взял бы нормальный инструмент.
Ok got it. Change both caps to 220uf 10v works great !!! This solves last led being dim, sequence is speeded just a little bit by cap on timer. paly around with the caps to get flash speed you want. Also you can discard the 4007 diode. Works fine without it.
Прекрасное видио. Спасибо! 👍👍👍👍👍
Bang saya mau tanya, resistor yang sudah tercantum ke lampu LED itu, berapa OHM ? Tolong balas saya 🙏 saya menunggu.
Speed control 👍
Навесная схема бегущих огней на 5-ти транзисторах. Набор деталей почти минимальный!!!
Nice. Your initial cascading circuit reminds me of something I designed on a bar napkin at 2 AM many years ago. My circuit had a different purpose and it was critical that it be integrated with a larger circuit by 8 AM. Fun memories.
Mạch này tui học rồi, dễ làm lắm
Neu minh su dung 100 hay 2_300 led thi sao,dau ss duoc k nhi
@@TaiNguyen-wj1fx xài cách khác, nội mà mắc mấy con đó chắc mua cho khỏe
Điện 12v khi qua ic 555 chỉ cho ra khoảng 5v hay 6v gì đó thui
@@tranvanquy6528 xài áp dc 3 _5 v à, đâu ai cấp 12 xì khói luôn sao
Very very nice
Good
Best offluck
I love Your "printed circuit board free" construction.
LivingCoolness That’s called “point to point” construction.
Another good idea would be if only one LED would switch on for a second, then it switches off and the next starts...and so on. Great work there!
The 555 timer could run slower with a larger value capacitor. With 1/2 Watt resistors and RED LEDs you could fashion a car turn signal.
Aetila Look at the CD4017 chip.
Great Vidio...
'
good nice LED project...
try add use a speed control from slow to fast
Хорошее изобретение, можете подсказать нужны моргалки на 24v. На прицеп,а то устал покупать, плафоны есть
Good job dear.
Can we increase the numbers of led?
Can we control the chasing speed of led?
Sir please mention all components in the comment. It's really amazing video!
احسنت تقسيم التيار كان منتظم ابدعت فى التصميم ولاكن انت انسيت حجه وفيه فكره جديدا ولى هيه التصميم والاطار وبداع فى تقسم الايظاه وهكى المقطع يخد وقت واكثر مشاهده اعجبنى
Buenas noches amigo. Excelente trabajo. Tengo una pregunta. Me soporta tiras led de 30 CM aproximadamente a 12vcc?
Ppl really need to get in to small ic I can make one strobe, zig zag, flicker or solid on a board smaller Than that 9v battery and run off 3v . Programmable as well. What I started doing years ago was when I found something that interests me I'd buy two of the items one I took apart and learned from and a lot of times I do have to ask someone who knows, trial and error. The 555 is cool but way to much work to many parts and room taken up. I started with stuff like this and by no means am I kicking it. It's a good learning experience and circuit. But wouldn't you like to build the same or more advanced the size of that 9v and a whole lot less parts? Good job on the circuit and it is important to learn and teach. No disrespect intended.
Vary vary nice video
Kya hum is ki speed ko variable bna sakty hain?
Reply please
Good idea
Big thanks, good idea, спасибо!😉
Hi Sir, good tutorial, so now, how to do if you need to make leds flashing every 60 minutes?
Good video that's help me!
great sir....!!! If I want use 5 Volt DC, what can i do?
Sir chashar se kitni led bulb Chala sakte Hain
Прикольная схема, но желаю автору поскорее узнать про существование флюса и научиться паять красиво и надёжно
Last led dim but works. I am still tinkering with it. If solved I will post resolution.
Excellent, I’ve wanting to do this for a long time. Thank you.
What is value of Resistor you last connect to IC 555 pin number 6 and 7.
Hello! Do you have the circuit in proteus?
¿Puedes hacer un amplificador de 30 Watts? (Can you make a 30 Watt amplifier?)
Спасибо! Очень доходчиво и всё просто! Thank you!
Ok
great sir i like that
The bulk charger have the same circuit, how do you mesuring the leds? How do you know that they are right?
otimo video parabens
Interesting component change would be to switch out one of the resistors on the 555 to a variable pot and you can change the speed of the LED's. Say to 50K. experiment a little bit.
Good project all the time. &very very clear.... Thanks
Hum isme aur kitne led badha sakte hain or kaise plz reply
Thà dùng thanh ghi dịch đỡ tốn linh kiện hơn
Very nice idea. Thank you my friend. 🌷🌷
Thank you Dear
Remove the 555, reduce capacitor of the transistor for 50 or 100uF use audio signal and have VU
What is this used for?
please , how can the diod discharge the capacitor , theoriquely impssible to discharge the capacitor throught the diod like this ??
10K and 220ohm resistance 1/4watts hay ya 1/2watts?
Absolutely beautiful project and execution! Very inspiring.
Great! You almost made it by selling this to Audi-the most profitable lamp factory
How long can a chain be built? with power 12v
The timing will change with longer chain. Just change values of caps for drain.
Wow
Sir please what is the name of the song used firstly
Para 3.7 vol??? por ejemplo con la pila 18650? sabrás? Saludos.
Hi,can i use 10 led for same extension .
Hello NE555N
NE555P
NE55555 dip 8
LM555
KA555
is it all the same? help? is there any difference?
Music ???
another project with the Ci 555 ... very cool, I would like to make one, but I can not find all the components!
Try Amazon they have EVERYTHING I get all my electrisions from Amazon
Excelente, gostei muito.
Obrigado pelo exemplar.
P
Not to be rude, but there is such a thing as Flux for soldering. Really helps out.
Yakov Yudin flux is in the solder.
@@vpistilli It isnt the same. Trust me.
@@RusoHacker007 So you are telling me that all those solder joints I made since my first job in 1965 until now are no good? All my employers would not agree with you. Yes, there are times that putting flux on maybe a piece of brass that is not tinned is necessary, but where he is soldering these components together, is OK just to use the solder with flux in it. The components he is soldering are pre-tinned. The flux in the solder is sufficient.
@@vpistilli Sounds good. Didnt mean to upset you. I just found whether the solder has flux or not, using soldering flux makes the solder flow a lot better.
Era isso que estava procurando! Parabéns e obrigado!
Cara vc sabe que parte só circuito da pra usar um potenciômetro?
Backsound?
Please explain how it works.
Parabéns pelo vídeo muito bom já vou me inscrever
Hey, great scheme. what value of the second capacitor which is sealed for 555 chips?
ok. bad watched a video.
It is 100uf 50v
Hello ! Can you send the circuit design? thank you!
how about 24v LED light can it run like that?
I think this is top secret. ;-)
Très intéressant
Nice
Thank you Dear
Super, GOD bless you
लेटरको भि जला सकते है क्या ? जैसे कि एक लेटर मे ३० लिड लगते है और एसा ५ लेटर है कैसे करें ?
agr ham is ko 12v 3amp pr chlaa chahy to kysy chlay
How to control led running speed.anyway great project.
Good
i want to use 4 led for per channel but end channel is dim light
Excelente trabajo. ¿ a que voltaje esta conectado?
Очень нужная в хозяйстве вещь.
Особенно в прихожей, сделал две шт, не знаю как без этого раньше жил
Alors où est ce qu'il faut placer un potentio pour jouer sur la fréquence de clignotement.
very good，If you can provide a formula to change the flashing time of the lamp is the best
Change the 555 capacitor to find the speed you want.
Easy, you go and farm your land and leave electronics to the clever one's.
How to increase speed of tht sequence
can I use it to 12 volts?
pregunto.... como se puede hacer ese mismo efecto pero de derecha a izquierda y viceversa en un solo circuito y si es posible con control de velocidad...
Good proyect.. thanks gracias
SUBSCRIBED
Красавэлло! Thank you!!!!!!
Take me also in this job.
nice
Kalo bikin jangan menggunakan batu batre.usahakan tegangan ac220 atau DC 24 vol /12 vol baru Berman FA at
Estaría bueno que dejes la lista de materiales que usas .
بھاٸ جان وہ اڈیو کے ساتھ جو ڈانس کرتے ھیں وہ ولا سر کٹ بنا کر بتاٸں
Muy bonito el circuito, pero..... por diossss Aprender a soldar que me duelen las retinas de los hojos al ver la tecnica que usais
A mí me duelen las retinas al ver como escribiste "hojos", todos tienen sus defectos, antes de hacer el comentario mejor subí un vídeo explicando cómo utilizar la soldadora y el estaño...
merci
タイマーIC 555
懐かしいですね
Está mal, en la colocación del diodo rectificador pone en pantalla el signo de positivo en el lado negativo (cátodo). Haz bien el vídeo y sorprende con tu circuito.
547 बोल्ड को नियम बना सकती इसलिए दुकान पर ही मिलेंगे
How if use led strip ?
Olá amigo, boa tarde! Se eu fazer esse pisca, da para fazer piscar mais rápido ou não? Pq eu quero fazer para usar como seta na bike! Valeu
Tenta diminuir a capacidade do capacitor, pode ser que funcione.
Why do not you use printed circuit?
Makasi infonya
Hasta cuantos LED'S soporta la instalación gracias y esta genial
Depende de la corriente de la pila supongo
necesito uno que esten todas prendidas y se vallan apagando de una por una podras hacer un tutorial
Невероятно полезная вещь. Но уж больно громоздкая ёлочная гирлянда. особенно кусачки для ногтей хороши. Для съёмки хоть в долг у кого взял бы нормальный инструмент.
Sir how to slow 40 second delay glow time please make video 👍