As an engineer I would not do this in series, raising the voltage from 220VAC to 290VDC-315VDC and split 27 strips so that each gets nearly 12VDC. When ONE wire or LED segment breaks, you will lose the whole light. Better to rectify 220VAC down to 12VDC with a large enough current supply and wire the strips in parallel. If one strip or wire goes bad, the rest remain lit. Might want to put a current limiting device in each strip so they're not exposed to the full increasing current as you lose strips or break wires. Voltage will remain constant, but the current will not as it will be divided among remaing good strips.
@@Kogacarlo But each piece barely has 10v on its terminals at ordinary 220v operation, how can they be able to draw more current as long as the voltage doesn't rise above 10v/piece?
@@yousufnofal9223 315 / 27 = 11,7 V. But I don't know how the voltage per strip will behave when you put these strips in series. My knowledge is too little.
@@Kogacarlo Simply the voltage is divided among them and the current is the same as if there is one strip connected, but the bridge doesn't output 327v, it rather outputs about 290v instead
@@kennmossman8701 it is definitely dangerous because there are exposed wires, but i don't know why it is dangerous to arrange lights like in the video, it seems okay to me. Would you be so kind to explain please.
@@jtucehok 1. First the circuit is more dangerous that you think; there is no fuse and the wrong type of cap is used [it should be a X type]. 2. Consider the strip itself. It has a direct connection [the power diodes dont count for anything] to the live Mains. For a standard interior strip there is that connection along the traces and leads - including the exposed tracks at the end. 3. Anyone touching the traces, leads, exposed ends and is grounded will be shocked. At up to 100mA it can be fatal. 4. This threat is expanded if the strip is resting on/touching a metal or damp surface. Imagine using it in the bathroom and an exposed part touches a damp wall - touching the wall where it is damp is a really bad thing.
I have an floor lamp, from the Chicago/Boston/Detroit series. I would like to convert the replace the dimmer board with something for leds instead but can't reall figure out how to do it. Can you do a video about that meaby?
Touching leds while its powered on may cause electrocution due to voltage differences between diifferent points. Do not use this at home. Nice content.
سلام من درست کردم نمیدونم چرا وقتی درایور رو وصل میکنم اولین ردیف از ال ای دی ها یک لحظه روشن میشه بعد میسوزه وقطع میشه تمام مراحل رو مطابق این کلیپ ساختم
Hi, good idea this other use of LED in 12V on 220V, however the support you show made in 3D printing I can not find the link in the description, can you tell me where I can possibly find it, not necessarily to redo this electrical assembly with these electronic components to rectify the 220V (I don't have any diodes at home and for the moment I don't have enough use for them to buy a batch, which is more interesting in terms of price, but you still need to have the use for them). On the other hand, your support can be used for 12V LEDs powered by 12V, so I might be interested in printing it to make another type of lighting.
At his home is 292V not 220V. So he did 27 strips and on each strip he had about 10V. On 220V outlet you would need 19 strips connected in series to have about 12V on each strip.
What are the two red plastic circles, are they specific for this work or are they related to something else that you used here? What are they related to?
عالی ایول، اگه امکانش هست لطفاً یک مدل چراغ قوه جیبی کوچیک که با یدونه باتری نیم قلمی کار کنه و در حد ۸۰ الی ۱۰۰ لومن نوردهی داشته باشه درست کنید دم شما گرم❤️🌹
This is ONLY a good idea IF: You find yourself locked in a basement of a night 😢😊darkness induced poltergeist hauntingand everyone has left for the weekend, the only lighting chance you'll have is to rip the cracked broken piece of LED strip in the trash, then clip off the old 1970s toasters plug off to make this OR your house is infested by spiders and you want it to burn it down completely. OR you're a psychopath and feed off of the bad energy from the people who did this and ended up burning their house down with their family and pets still inside.
Why go through all that when you could just buy a led lamp for a few dollars 😅😂 what a waste of time i bet you spent more in materials that what an actual lamp cost genius 😂.
Thank you for watching this video. If you have a new idea for a new video and the quality of the videos. Please write it to me.🙏
super 🤩🥳👌video sir .next video please make rgb decoration light with animation🙏
Titit mu di masak
does led bulb work on series ?
What is thw wattage consumed on this type of light??
@@ravikumarg4698qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
⚡️caıtion:
Please don’t touch the led lights during operation due 300v risk
✋❤❤❤❤❤❤
As an engineer I would not do this in series, raising the voltage from 220VAC to 290VDC-315VDC and split 27 strips so that each gets nearly 12VDC. When ONE wire or LED segment breaks, you will lose the whole light. Better to rectify 220VAC down to 12VDC with a large enough current supply and wire the strips in parallel. If one strip or wire goes bad, the rest remain lit. Might want to put a current limiting device in each strip so they're not exposed to the full increasing current as you lose strips or break wires. Voltage will remain constant, but the current will not as it will be divided among remaing good strips.
BIG MISTRAKE! no resistor to limit the inrush current - good way to burn out the LEDS!!!
The small boards do have resistors I think.
@@Kogacarlo the strips have - you are right, but they are designed to work at the normal rated voltage. They do little at a turn-on surge
@@Kogacarlo
But each piece barely has 10v on its terminals at ordinary 220v operation, how can they be able to draw more current as long as the voltage doesn't rise above 10v/piece?
@@yousufnofal9223 315 / 27 = 11,7 V. But I don't know how the voltage per strip will behave when you put these strips in series. My knowledge is too little.
@@Kogacarlo
Simply the voltage is divided among them and the current is the same as if there is one strip connected, but the bridge doesn't output 327v, it rather outputs about 290v instead
Congratulations on the success of quality products like this. I really enjoyed it.
Thanks Bhai maza aagaya
Молодец)
Но на алике такие кукурузы 5 лет назад продавали)
А с такой класной светодиодной полосы можно сделать что то намного полезней)
ни защиты ничего... он походу для алика товары проектирует
✋❤❤❤❤❤❤
It's a dangerous project, don't try to arrange like this
Why? If you warn people, you should explain why, otherwise it is hard to believe you.
@@jtucehok You do not know why???
@@kennmossman8701 it is definitely dangerous because there are exposed wires, but i don't know why it is dangerous to arrange lights like in the video, it seems okay to me. Would you be so kind to explain please.
@@jtucehok
1. First the circuit is more dangerous that you think; there is no fuse and the wrong type of cap is used [it should be a X type].
2. Consider the strip itself. It has a direct connection [the power diodes dont count for anything] to the live Mains. For a standard interior strip there is that connection along the traces and leads - including the exposed tracks at the end.
3. Anyone touching the traces, leads, exposed ends and is grounded will be shocked. At up to 100mA it can be fatal.
4. This threat is expanded if the strip is resting on/touching a metal or damp surface. Imagine using it in the bathroom and an exposed part touches a damp wall - touching the wall where it is damp is a really bad thing.
✋❤❤❤❤❤❤
Wow
So Good
So Thank bro
Brilliant bro🎉 nicely done video as well teaching !
Should share the amazon links as well regarding raw materials.
What you have shown in thumbnail of this video, do you have video link for it?
Why, you can clearly see what's going on.
Don't expect it to work, though.
Finally the simple detail yet crucial that I have been looking for in all those useless videos so far. Thank you man!
✋❤❤❤❤❤❤
I have an floor lamp, from the Chicago/Boston/Detroit series.
I would like to convert the replace the dimmer board with something for leds instead but can't reall figure out how to do it.
Can you do a video about that meaby?
Touching leds while its powered on may cause electrocution due to voltage differences between diifferent points. Do not use this at home. Nice content.
Good❤❤
عالییییی
Good
✋❤❤❤❤❤❤
سلام، داداش میشه در مورد بازدید کننده های اصلی کانالت که از کدوم کشور هستن و میزان درآمد کانال بگی؟ مثلا آر پی ام کانالت چقدره؟
Very useful video friends
❤️🙏
✋❤❤❤❤❤❤
❤great job 😊
Thanks 😄
✋❤❤❤❤❤❤
Is that 1 ampere 12v??
سلام من درست کردم نمیدونم چرا وقتی درایور رو وصل میکنم اولین ردیف از ال ای دی ها یک لحظه روشن میشه بعد میسوزه وقطع میشه
تمام مراحل رو مطابق این کلیپ ساختم
سلام خسته نباشی خیلی خوب بود ممنون لذت بردیم ❤❤❤
✋❤❤❤❤❤❤
really cooooooooool
This led. Stip. Connecting. Series....??
How many ledd in 1 strip?
✋❤❤❤❤❤❤
Hi, good idea this other use of LED in 12V on 220V, however the support you show made in 3D printing I can not find the link in the description, can you tell me where I can possibly find it, not necessarily to redo this electrical assembly with these electronic components to rectify the 220V (I don't have any diodes at home and for the moment I don't have enough use for them to buy a batch, which is more interesting in terms of price, but you still need to have the use for them). On the other hand, your support can be used for 12V LEDs powered by 12V, so I might be interested in printing it to make another type of lighting.
A 1 Amp 1000 PIV diode bridge is cheap. But this is a very bad design and is dangerous
At his home is 292V not 220V. So he did 27 strips and on each strip he had about 10V. On 220V outlet you would need 19 strips connected in series to have about 12V on each strip.
@@vytautasmotiejunas7639 you are so wrong... To convert AC to DC voltage you must multiply by a square root of 2 or ~1.41
3:58 hello 👋
Excellent project 👍👍🙏🙏🔥🔥❤️❤️❤️
Thanks for watch.☺️
Highly dangerous project
✋❤❤❤❤❤❤
Nice work ❤
Thank you! 😊
✋❤❤❤❤❤❤
Einstein. 👏
Amazing
به به پست جدید🎉
بلی ☺️☺️
✋❤❤❤❤❤❤
what is the width of the wire?
✋❤❤❤❤❤❤
That's amazing
How To Make 24w Please Help
Excellent bro
✋❤❤❤❤❤❤
සුපිරි
*Horrific* unsafe practices here. You're responsible for all those who ignorantly copy you.
totally agree
no hes not
awesome✌🏻✌🏻 Lovely Best 9205 Multimeter 💪🏻❤️
Thanks ✌️
Sir in which city do you live
im from iran
and city
grate man♥
Crative idea good
Thanks a lot
Hello if Led smd If we cut 10 pieces, there will be a problem😊
✋❤❤❤❤❤❤
Idenya sungguh kreatif sangat kawan
✋❤❤❤❤❤❤
хорошо делаешь
✋❤❤❤❤❤❤
Good job sir, I am. Very appreciative from your work.
Keep it up 👍
✋❤❤❤❤❤❤
Lights jali nhi hai us py marker mara hai
this is freakin AMAZING✨✨
My opinion is that it's dangerous
What are the two red plastic circles, are they specific for this work or are they related to something else that you used here? What are they related to?
✋❤❤❤❤❤❤
WARNING!!! this circuit is DANGEROUS! a serious shock is possible, even a FATAL shock
It is very irresponsible not to warn viewers
Every exposed circuit is dangerous, but why this in particular?
1. ANYONE TOUCHING THE STRIPS COULD BE SHOCKED
Hi could you make a video of how to do this the right way? Use 220 with a led strip
ansforming 220v into LED brilliance? Consider me enlightened! This video makes DIY lighting look like a piece of cake
Very nice sir ji
✋❤❤❤❤❤❤
9v. Idea.🙏
Hello coach, I followed the video but how to make it flash Which transistor should be added and how to master it?
very nice
and very good
✋❤❤❤❤❤❤
Super Video Sir
Good Idea
✋❤❤❤❤❤❤
Nice
Very nice
Nice 🎉
supeur video
very good thak.
Crative.
عالی ایول، اگه امکانش هست لطفاً یک مدل چراغ قوه جیبی کوچیک که با یدونه باتری نیم قلمی کار کنه و در حد ۸۰ الی ۱۰۰ لومن نوردهی داشته باشه درست کنید دم شما گرم❤️🌹
ایول بچه شهر
How ti make same circuit in flasher
Super
✋❤❤❤❤❤❤
NO explantion, few details, no tips/hints/traps............very poor effort
As made it ,Sir would like to u that do we have use the same circuit board for a solar panel 3W 8.97v 3A or any changes to be done
سلطان کجایی دلتنگت بودیم ؟قهری با ما ویدئو نمیزاری
هامیم جان درگیر دانشگاه بودم ولی دیگه تمومه از این به بعد بیشتر هستم
My dude you’re going to be responsible for someone killing themselves… how about be responsible for taking this video down.
Jos
Screen shot alag aur video alag. ...
✋❤❤❤❤❤❤
U now Need to wear sunglasses when light on
✋❤❤❤❤❤❤
That thumbnail can make someone do something really stupid and dangerous
truly horrible construction
✋❤❤❤❤❤❤
Please make it as rechargeable
Отличная штука ещё бы плафончик какой нибудь от пыли и было бы вообще шикарно
✋❤❤❤❤❤❤
Akh bana ke dikhao
Hi
Menit menit yang sia sia
Z(2?
Fucking death trap.
agree
This is ONLY a good idea IF:
You find yourself locked in a basement of a night 😢😊darkness induced poltergeist hauntingand everyone has left for the weekend, the only lighting chance you'll have is to rip the cracked broken piece of LED strip in the trash, then clip off the old 1970s toasters plug off to make this
OR your house is infested by spiders and you want it to burn it down completely.
OR you're a psychopath and feed off of the bad energy from the people who did this and ended up burning their house down with their family and pets still inside.
so you are using FOUR diodes to make the bridge - that is not clear
do NOT twist the leads like that - very poor practise
Why go through all that when you could just buy a led lamp for a few dollars 😅😂 what a waste of time i bet you spent more in materials that what an actual lamp cost genius 😂.
Absolutely foolish idea. 300 v DC is fatal
Mobile detail mein batao mines plus thoda dhire dhire banakar tha ki ham log bhi banaa
You are tired to live ?
👍
الحمدلله ماشاءالله الحمدلله
✋❤❤❤❤❤❤
👑👑👑👑
Bekar
燈炮
pls be vegan animals also have lifes
Never try this
Non sono molti quelli che traducono i commenti!....
😂😂