How To Step by Step AC Compressor Front Seal Replacement/Reseal/Shaft Seal
Вставка
- Опубліковано 15 чер 2024
- Repair / Rebuild kompressor wira DENSO / Lip's shaft seal. - bit.ly/3zK5V2y
How to Properly Recharge Your AC System / Cara isi gas Aircond kereta - www.shorturl.at/bdiqO
0:00:00 - Intro
0:00:09 - Disclaimer
0:00:26 - Compressor model DENSO 10PA15C
0:00:36 - Compressor has a leakage problem
0:00:47 - Damage O-Ring / Shaft Seal / Lip's seal
0:00:55 - Sign the compressor shaft seal failure
0:00:59 - oil under the car's hood
0:01:20 - some oil on the compressor pulley and around the compressor head
0:01:47 - Lip sealed / Shaft seal Denso 10PA15C
0:01:55 - Shaft Seal Protector Installer / Remover
0:02:07 - 1 Set O-Ring Compressor
0:02:10 - ND8 Compressor Oil
0:02:15 - 6 mm Hex Socket
0:02:19 - 10 mm socket
0:02:23 - Snap Ring Pliers
0:02:28 - Lots of Rags or Paper Towels
0:02:40 - Torque Wrench
0:02:42 - Phillips Screwdriver
0:02:46 - Flat Screwdriver
0:02:48 - Compressor Schematic Denso 10PA15 C
0:03:06 - Removing the Clutch Assembly
0:03:15 - Pulls off the Drive Plate
0:03:26 - Remove Pulley Circlip it using a Snap Ring Pliers
0:03:36 - Take Off the Pulley
0:03:36 - Remove the Ground Wire
0:04:05 - Remove the Magnetic Coil Circlip
0:04:08 - Pull the Coil off
0:04:20 - Remove the five Compressor Head Bolts
0:05:20 - Prying the front section of the Compressor
0:05:29 - The Cause AC Leaks
0:05:20 - Remove Snap Ring that hold the lip seal in place
0:06:02 - Push down the Lips Shaft Seal using
0:06:14 - Damage Lips Seal / Split into 2 pieces
0:06:25 - Clean the Shaft Housing from the older Lips Seal Carbon
0:06:33 - Remove the two-indexing pin
0:06:37 - Separate the Compressor sections
0:06:38 - Clean all the part off the Compressor
0:07:10 - Separate the middle sections of the Compressor
0:07:54 - Clean all the component and put back as before
0:08:12 - Coat the new o-ring install it
0:08:17 - Put back the middle section of the Compressor
0:08:23 - Lubricate the Compressor with some oil
0:08:51 - Position the two-guide pin on the Compressor
0:09:01 - Install the front suction valve, matches it with the pins
0:09:25 - Lubricate the Lip Shaft Seal
0:09:37 - Gently push the Lips Shaft Seal using 21mm socket
0:09:53 - Install flat surface Retainer facing the Carbon Seal
0:10:20 - Place the shaft seal protector over the shaft
0:10:38 - Shaft Seal Protector Installer keep the Seals in perfect condition
0:10:58 - Coat the new Shaft Seal and the Shaft Seal Protector
0:11:07 - Push down the compressor head with the new Seal in it
0:11:22 - Turn the Compressor upside down
0:11:33 - Remove the rear cover and change with the new O-Ring
0:13:09 - Insert the five through bolts
0:13:13 - Tightened the bolts with a star pattern
0:13:27 - Torque the bolt to 21Nm
0:14:10 - DENSO 10PA15C uses ND-8 oil - quantity 120 cubic centimeters
0:14:34 - Put in Compressor oil, rotate the Compressor
0:15:08 - Check the Compressor, sealed correctly??..
0:15:35 - Last O-Ring, on the top of the Compressor
0:16:03 - Reattach four screw bolts, torque it to 21 newton meters
0:16:53 - Put the Clutch Coil onto the Compressor
0:17:17 - Put the flat side snap ring facing the Magnetic Coil
0:18:46 - Congratulations, you have just rebuilt your AC Compressor
Dalam video ini, saya akan berkongsi dengan anda semua. Cara untuk rebuild semula kompressor air cond kereta. Kompressor ini ada masaalah leaking. Dan saya rasa, masanya sudah sampai untuk saya overhoul kompressor ini. Model bagi kompressor ini DENSI 10PA15C.
ITEM USED
invol.co/claxngf - AC Denso Compressor Shaft Lip Oring Seal Kit
invol.co/claxnhq - 10PA repair O-Ring Kit
invol.co/claxnir - ND-8 compressor oil
invol.co/claxo0l - Hex Shank Impact Socket 6mm
invol.co/claxo1b - F rod Breaker
invol.co/claxo1x - DEEP SOCKET 10mm
invol.co/claxo2m - Torque Wrench
invol.co/claxo33 - Flat Screwdriver
invol.co/claxo3u - Philips Screwdriver
invol.co/claxo44 - Long Nose Pliers
invol.co/claxo4n - Snap Ring Pliers
invol.co/claxoc3 - Impact Wrench Cordless
invol.co/claxodr - RATCHET WRENCH
In this video, I will share with you guys. On how to rebuild a compressor. It might help others who are thinking of fixing their compressor. This compressor has a leakage problem. You will notice the face of the compressor is damp with lots of oil. The model for this compressor is the DENSO 10PA15C. The process for replacing the compressor itself is fairly simple. However, replacing it alone is not advised. I would suggest a full replacement of all o-rings in the system (since there may be leaks). As you remove them, take note (or take photographs) of the arrangement of spacers for each bolt, as they must be put back in the same locations. You also need to change it with new compressor oil.
#rebuild
#compressor
#denso
#Denso10PA
#reseal
#Nippondenso
#leaks
#refrigerant
#shaft
#sealed
#gasket - Авто та транспорт
Masha_Allah nice and Informative video. Support and Love from Pakistan.
Terima kasih bang .kongsi ilmu jelas dan penerangan pon baik..baru faham cara kerja ..compressor 10pa15c.
awesome video, simple and informative thankyou very much
Salam tuan.klau kita beli lip's seal dpt sekali dgn protector tu x?
Gerçek bir ustasın🤩
Very informative. Thank you
Excellent instructional video, thank you!
Good job
Thank you for posting this most valuable video on UA-cam. ❤❤😂
Sangat sangat bermanfaat
This is a good video!
Thank you for your video sir.
TerBaik Tuan💯💢💯💢👍👍👍
Terbaik
Awesome bro, this is what i need
nice job.. thanks..
Thank you,sir!
Thank you, I have like and subcrive your magnificient video. Ps : I watch this from Indonesia.
Terbaik. Penuh dengan Info berguna.
Mantap
Proper work
Nice video thank you. Can you share schematic document for this compressor?
Good video!
powerlahh... 👍
Would this apply to a Denso 471-0124 compressor?
That was a great video. I wish I could find a rebuild kit for my mitsubishi 3000gt compressor because they are obsolete now.
head down to your local bearing and bolt store, most sell seals take seal with you they maybe match it. or a hydraulic parts store. I never buy seals from genuine or parts stores and ive always got what i need and I fix all sort of stuff.
I think I have a similar problem with a BMW N20 AC compressor shaft seal. And a issue locating the seal
Hi just curious does this model have rings on the piston. I could not make it out. I’ve got one out of my sons car. And it has no rings. Same model.
Thanks Errol
Well done. A very detail and informative video.
By the way where can I get hold of Denso 10P15 series compressor service manual?
User Manual
drive.google.com/file/d/1HV4d5qN7vokJ9utN9HmYiMxrE_CvvsaP/view?usp=sharing
drive.google.com/file/d/18xchRPSiS4IsIhbxD4dWdSW9BM5fYIsN/view?usp=sharing
drive.google.com/file/d/1FQ74dnvEktK3KK34laK6w7jlE4K6PDPg/view?usp=sharing
drive.google.com/file/d/165vrxrXiCgdj_3NIvcRKnRx6zAXrAQhl/view?usp=sharing
drive.google.com/drive/folders/1G57F3NWT3xXZV7KN4Mn3Lv_haJf0u5k9?usp=sharing
hai bos nak test bocor air pressure masuk dekat suction atau discharge?
mane2 bos.. masuk 100psi da boleh test leak..
Question; after we finish do reassmbling the compressor, so no need to do the vacum to suck the air from the system right? Cause it will also suck the oil that we have put in it, right? Please answer this question, thank you in advance
Vacuuming only removes gases, not liquids. Oil does not turn into a gas, it stays as a liquid, so it will not be pulled out. Water, for example, will boil at high vacuum, and the steam or gas will then get sucked out. If you had a leak in the system, some oil may have leaked out and needs to be replaced.
The a/c system still needs to be vacuumed out, no matter what. The air in the system is bad and can cause more problems than just making it cooler.
Can i know size of clutch bearing in thos video?
bearing size
Inner diameter x Outer diameter x Width: 22 mm
30 x 52 x 22
Are they the same tools with the type of 10PA 13C?
yup.. same item..
@@pro2chiloxbut for 10PA 13C, it doesnt use any rubber set oring, it use a packing from slight plat metal. My question is; since it doesnt use any rubber, can I use gasoline to do cleaning with any fabric towel? Or just use any fabric towel like your tutorial with ni gasoline?
mana nak dapat sparepart kompressor ya?
Shopee
Great video and info!! Sir I have a 1991 Nissan 240SX that I am rebuilding well, the AC compressor don’t work anymore so I want to rebuild it instead of trying to buy a aftermarket one.
What parts would you recommend me replacing and where could I find those parts? Thank you so much for all your help!!
Kompresor klo jem xde wt repair ke
kalau jem x bley buat bos, piston dah lekat, mmg kene ganti baru..
@@pro2chilox xde buat part time repair2 brg org ke
Ganti shaft seal hanya 8 hari leak lg as sudah kasih gosok kenpa ya kak
over charge gas agaknya.. berapa reading manifold masa ac engage..
@@pro2chilox gas pressure low 40 high 160psi
That’s fake oil and it’ll not mixed well with refrigerant at all.
Bari good
Good job