I just made 4 of these docks! I used 12’ 2x8s for the frame. The movable winch is genius engineering! They work great. I appreciate these videos with creative ideas. Nice job and thanks.
This is really cool, and great direction dude. Just got me a 2004 Sea Doo GTX and a guy on my lake here in Alberta 🇨🇦 is selling a variant of this for $800. I wanna try it cheaper, so…challenge accepted!!
Great idea! Do you support it in the ground somehow? I would think it would slide toward the sea doo when you crank it up. I’m definitely going to make one though, Thanks for the idea!
Hi Bernie- I actually didn’t support mine to the ground, but I set mine on a rough gravelly area. It would sometimes pull an inch or two toward the water, but usually I could step on the landing ramp and it would stay put. A little ground support would be a good idea!
Hey Guy! I’m in Northern MN, just a couple hours from Canada, but pretty good guess! The center to center distance 16.5”. I based that on the hull of my jet skis. Thanks for watching!
Well, I am not handy, but I am building this PWC ramp for my Seadoo RXT 255 for the lake in Canada. It actually has gone well. I'm almost done. I have to complete the winch stage. I do have an issue transporting it because its 12 feet long (Seadoo is just over 10 feet). So, I plan to cut it in half and use metal hinges to reattach it when I get it to the lake. Thanks for the easy to follow steps.
Hi @Michael Sharpe - that’s s good question! If you replaced the pvc pipes with two rows of casters, I don’t see why it wouldn’t work. Would you haul the whole assembly on a tilt trailer? That wouldn’t be a bad way to go!
Hi - good question! Yes, sometimes the lift will shift a little, moreso up than out toward the water. Out of habit, I just put one foot on the lift while I’m cranking. It’s not been a problem for me. Thanks for watching!
Did u consider rollers instead of pvc? What about a keel roller fo when you first go on? Do you anchor your ends somehow in the water. Considering this or the multinautic one, but this looks durable and cheaper
I went with pvc as a cost saving measure. My skis are old and I bought them pretty cheap. I didn’t want to spend a lot in the ramps. The ends aren’t anchored, but that’s not a bad idea. Mine are sitting on concrete and gravel, so they don’t slide much. I usually put my foot on the ramp while I start cranking to keep it from shifting.
Hey my seadoo is bigger than yours do you think it would still work? Would it be better cuz their smaller to put more of the ramp in the water? Great idea!
Yeah it should still work. Might want to look at a winch with a longer handle to make it easier to crank up. Definitely measure on your hull to make sure you don’t end up rubbing in the middle. You’ll want to err on the narrow side to be sure. The back 6-8” of my ramps are in the water, depending on lake level.
Hi Jean Sébastien- I think it would work. Just be sure to measure the hull to see how far apart your pipes can be so it doesn’t scrape the cross supports. Good luck!
Hi markbelina07- took me a bit to put it all together. I spent about $450 on this project. About $390 was for the lumber, with the rest being for spax screws and rebar. All of my sand and gravel was free from a local iron ore mine. Note that this was at pre-covid prices! Today the project would cost about $750! The 4x4’s went from about $1.20/ft to $2.00/ft. I needed 30 - 6’ posts and 18 - 8’ posts. I hope this helps!
@@NashwaukSteve yeah, this is my only concern, too. I did measure and have spaced it 24 inches apart (RXT 255 is a big three seater). My solution if I screwed up once I test it is to replace PVC pipe with larger pipe. I can probably go up to 2 inch pipe if needed.
I just made 4 of these docks! I used 12’ 2x8s for the frame. The movable winch is genius engineering! They work great. I appreciate these videos with creative ideas. Nice job and thanks.
Incredible job. Followed your directions and made two in about 4 hours. Works like a charm. Skis fit perfect!!! THANK YOU!!!
Great!! Happy to hear that!
Love the kid looking at the camera at the beginning!
Thanks! Great step by step, concise and to the point. Much appreciated!
Glad it was helpful!
Great idea! I’m in the process to adding a jet Ski slip to my dock and I’m going to incorporate your idea while building it. I like the PVC ramps!
Nice quick and easy build... Im going to make two today
Good idea I would put the front gusset on the inside with the angle on the front to make it stronger
I use this for my stand up jet ski
Thanks for posting!!
You bet!
This is really cool, and great direction dude. Just got me a 2004 Sea Doo GTX and a guy on my lake here in Alberta 🇨🇦 is selling a variant of this for $800. I wanna try it cheaper, so…challenge accepted!!
Hey @David Stock! Thanks for watching and commenting. Good luck on your build. I just wish lumber was cheaper for you!
I like the pvc slide ideal
Excellent! Thank you
Great idea! Do you support it in the ground somehow? I would think it would slide toward the sea doo when you crank it up. I’m definitely going to make one though, Thanks for the idea!
Hi Bernie- I actually didn’t support mine to the ground, but I set mine on a rough gravelly area. It would sometimes pull an inch or two toward the water, but usually I could step on the landing ramp and it would stay put. A little ground support would be a good idea!
Hi Steve from Canada. Would you remember the measurement in inches between the center of both pvc pipes ? Thx a lot and good job !!!
Hey Guy! I’m in Northern MN, just a couple hours from Canada, but pretty good guess! The center to center distance 16.5”. I based that on the hull of my jet skis. Thanks for watching!
Well, I am not handy, but I am building this PWC ramp for my Seadoo RXT 255 for the lake in Canada. It actually has gone well. I'm almost done. I have to complete the winch stage. I do have an issue transporting it because its 12 feet long (Seadoo is just over 10 feet). So, I plan to cut it in half and use metal hinges to reattach it when I get it to the lake. Thanks for the easy to follow steps.
Glad it’s going well. The hinge idea sounds great for transport!
I have the 155.. wondering how you made out! Any updates or dimensions are appreciated!
It’s finished..haven’t tested it yet because we can’t currently go to Canada. I plan to try it out on a small lake nearby...
I’ll put those dimensions up when I get home...👍
You didn't lie about your material list you just forgot. That's my motto
This is gold. Subbed, and def building
Great video Steve. Do you think this would work with caster wheels to launch from a boat ramp?
Hi @Michael Sharpe - that’s s good question! If you replaced the pvc pipes with two rows of casters, I don’t see why it wouldn’t work. Would you haul the whole assembly on a tilt trailer? That wouldn’t be a bad way to go!
When you started cranking the jetski up on the lift did the lift start pulling itself into the water or did it stay in place?
Hi - good question! Yes, sometimes the lift will shift a little, moreso up than out toward the water. Out of habit, I just put one foot on the lift while I’m cranking. It’s not been a problem for me. Thanks for watching!
do you have a set of plans for this Jet ski ramp that i can get? This is one of the best ideas i have seen.
Sorry, I didn’t make plans. I just used some sketches during the build to record my measurements.
Awesome idea be sweet if anyone had any plans
great video thanks
Did u consider rollers instead of pvc?
What about a keel roller fo when you first go on?
Do you anchor your ends somehow in the water.
Considering this or the multinautic one, but this looks durable and cheaper
I went with pvc as a cost saving measure. My skis are old and I bought them pretty cheap. I didn’t want to spend a lot in the ramps. The ends aren’t anchored, but that’s not a bad idea. Mine are sitting on concrete and gravel, so they don’t slide much. I usually put my foot on the ramp while I start cranking to keep it from shifting.
Hey my seadoo is bigger than yours do you think it would still work? Would it be better cuz their smaller to put more of the ramp in the water? Great idea!
Yeah it should still work. Might want to look at a winch with a longer handle to make it easier to crank up. Definitely measure on your hull to make sure you don’t end up rubbing in the middle. You’ll want to err on the narrow side to be sure.
The back 6-8” of my ramps are in the water, depending on lake level.
What was the cost on materials
I'm thinking of building one, do you think it would work for a Sea-Doo Spark?
Hi Jean Sébastien- I think it would work. Just be sure to measure the hull to see how far apart your pipes can be so it doesn’t scrape the cross supports. Good luck!
@@NashwaukSteve That's exactly what I was thinking. What a neat design you made!
Hi Jean! I also just bought a Sea-doo spark, how wide did you make the cross supports?
What was your total cost of the build?
Hi markbelina07- took me a bit to put it all together. I spent about $450 on this project. About $390 was for the lumber, with the rest being for spax screws and rebar. All of my sand and gravel was free from a local iron ore mine. Note that this was at pre-covid prices! Today the project would cost about $750! The 4x4’s went from about $1.20/ft to $2.00/ft. I needed 30 - 6’ posts and 18 - 8’ posts. I hope this helps!
What is the overall width of the ramp?
Mine is 21” wide, except for the gusset supports near the front. That part is 24” wide.
Would the bottom of the ski not hit the wood?
As long as you keep the pipes from being too far apart it will clear. Mine does not rub.
So do u need to Measure it to fit my mine?
Yes, it would be recommended.
@@NashwaukSteve yeah, this is my only concern, too. I did measure and have spaced it 24 inches apart (RXT 255 is a big three seater). My solution if I screwed up once I test it is to replace PVC pipe with larger pipe. I can probably go up to 2 inch pipe if needed.
Would your spacing be the same as your trailer spacing.