At the old tecnical school we learn " controler forward and reverse using contactor magnetic by 220v ac....replace the coil with 12vdc...and dont forget to use relay 12vdc for safety.
Hello! I'm currently putting 2x controllers and 2x motors in my scooter. 2WD Dualtron 2x 48V 1000W motors and I have 1x main controller + 1x subcontroller! Question: Do I have to connect all 2 controllers with Y cable parallel cable, these two controllers together and then connect them once to the 48V 24Ah battery? The main controller and sub-controller are connected with a 5 pin connector and on the main controller there is 1x display connector + 1x 3 pin gas connector. Or do I just have to connect the main controller once to the 48V 24Ah battery?
Good morning. Hello from Kazakhstan. Watching your video. That all wires can be bridged in parallel? I'm talking about the controllers, what you did with one wire output by color. Thanks.
Hi, I know it's a year late but you really don't want to do that. Most motor controllers rely on reading the current draw in each coil to determine the position of the rotor. This is used for soft-starting the motor, i.e. avoiding large current spikes when starting the motor up
Thanx for the video....In my dual motor scooter I upgraded my 52V battery from 20 Ah to 26ah but my bms overheats and has to be replaced constantly.....the BMS is rated at 52V 30A.....do you have a suggestion....Thanx.
Ich habe Hauptcontroller + Untercontroller von Brainpower jeder Controller hat 48V + Current 38A ! Wenn ich den Akku mit Y Parallel Kabel alle zwei Controller anstecken und danach einmal zum Akku habe ich dann nicht 38A current x 2= 76A Current?? Denn bei Parallel bleibt 48V gleich und Ampere werden zusammen gezählt bei Akkus zum Beispiel. Ist das bei den 2x Controller Set auch so?? MfG.
Hi friend . I am going to build a16000 watt escoot 2x8000w motor I’m good with the fabrication \build . But am not good at all with the electrical side . Can you please advise on what battery’s and controllers I will need for build I want 80plus volts kind regards thanks
Hello. Your video it really great. But please tell me if i have two controllers but there is the option of three speed witch. How do i connect the wires ? do you think i can use one switch wit three speed option to connect two controllers together ? or i need to have a second switch ? an connect them separately ? thank you for your help an answer.
I am also wondering about that...in my dual motor scooter I upgraded my 52V battery from 20 Ah to 26ah but my bms overheats and has to be replaced constantly........
Is it a 48V battery fully charged or is it a 52V fully charged? Each battery will be alot higher voltage when fully charged your BMS is not up to the job get a higher rated BMS and add a heatsink to keep it cool
Hello I have been doing this same test on my scooter . I noticed with my two controllers that are 48v 1000w that only the assist controller has self learning wires. So I can get self learning speed up to work with 1 wheel like u did in ur video. What about self learning on the main wheel. So we can get the low torque right on both wheels.
Hi!! How can i add more speed to my scooter with 48v 18ah battery, 800w dual motor(2200), it run at 25kmh but i need more speed..shoukd i change my motor to higher watts or should i change my motor controller?
@@Laamlee-yt Trc mình chế nghịch cái 3 bánh cho trẻ con chơi cũng chạy 2 ic riêng. 2 bánh sau lấy nguyên bộ giá đỡ của xe cb, còn trc là xe đạp trẻ e. Đợt này muốn làm thành scooter mà cũng bị thiếu vật tư. Sợ nhất kiểu chưa có exp mà đang làm mới biết thiếu gì chạy đi mua giờ này mới khó.
I mean with 2 different controllers and motors, the speed will not sync if running at the same time, resulting in waste of energy. Of course it is possible to use only one of them
Hi, I have e scooter with BLDC Hub Motor 800w of a 48V 21A battery, my problem is it can't go uphill with over 17 degrees angle, how can I go atlease 35 degrees angle uphills?
hello, i'm planning to build an electric scooter, i will buy scooter frame, 2 48v 500-1000w motor and 2 48v 500-1000w controler, does a single throtle dsiplay work with 2 motor at once? and will the 3 speed mode will work? please help me
It would have been better to explain in voice what he was doing. Plus it would be better if he used two throttles so he could use back wheelbthe front would not be working until he used other throttle. Or the other way take taping of throttle wire from controller and put a switch in line. That would give instant speed from front wheel two throttle is best. Like the top gun bikes they have one thumb and twist
Hiya I have got Dual 2 motor electric Scooter 1200watt but the problem no Speed Control just handle like motorbike just up and Down roles So please can you let me how I can Change the handle and I can send you a photos for the Electric Scooter thanks
It is possible to do the same but that a controller does not have a trottle, it simply takes care of obtaining energy. Is it possible that controller A can draw power from the battery at the same time as controller B recharges the battery? Could there be a problem? Thx
@Diego Vidal yes you can do that but it's totally useless, the efficiency of the regenerative breaking would be less than 99% and around 75/80, completely useless
Hm kaya aabutin I'm using mober kasi plan ko gwin dual hub for additional speed kc 36v 8ah lang sya additional batt sana plan ko and gwn ko dual hub possible kaya? And san po location niyo kayo po ata yung nag post sa marketplace
trên shopee bán nhiều mà e. ic tầm 200k~300k 1 cái. Motor 4~500k, e mua loại có sẵn dĩa chế cho khỏe, pin thì tùy e muốn đi xa hay quanh quanh chọn dung lượng cho phù hợp
At the old tecnical school we learn " controler forward and reverse using contactor magnetic by 220v ac....replace the coil with 12vdc...and dont forget to use relay 12vdc for safety.
coole Arbeit
mit welchen kabeln hast du die 2 controller verbunden
Hello! I'm currently putting 2x controllers and 2x motors in my scooter. 2WD Dualtron 2x 48V 1000W motors and I have 1x main controller + 1x subcontroller! Question: Do I have to connect all 2 controllers with Y cable parallel cable, these two controllers together and then connect them once to the 48V 24Ah battery? The main controller and sub-controller are connected with a 5 pin connector and on the main controller there is 1x display connector + 1x 3 pin gas connector. Or do I just have to connect the main controller once to the 48V 24Ah battery?
Good morning. Hello from Kazakhstan. Watching your video. That all wires can be bridged in parallel? I'm talking about the controllers, what you did with one wire output by color. Thanks.
Hi, I know it's a year late but you really don't want to do that. Most motor controllers rely on reading the current draw in each coil to determine the position of the rotor. This is used for soft-starting the motor, i.e. avoiding large current spikes when starting the motor up
Sao a ko quay khúc lắp đĩa xong r lắp cùm, e thắc mắc đoạn đó
Thanx for the video....In my dual motor scooter I upgraded my 52V battery from 20 Ah to 26ah but my bms overheats and has to be replaced constantly.....the BMS is rated at 52V 30A.....do you have a suggestion....Thanx.
Bigger heatsink and add fans for additional cooling
Se me ocurre la idea de crear un súper dron con estos motores.
Ich habe Hauptcontroller + Untercontroller von Brainpower jeder Controller hat 48V + Current 38A ! Wenn ich den Akku mit Y Parallel Kabel alle zwei Controller anstecken und danach einmal zum Akku habe ich dann nicht 38A current x 2= 76A Current?? Denn bei Parallel bleibt 48V gleich und Ampere werden zusammen gezählt bei Akkus zum Beispiel. Ist das bei den 2x Controller Set auch so?? MfG.
Hi friend . I am going to build a16000 watt escoot 2x8000w motor I’m good with the fabrication \build . But am not good at all with the electrical side . Can you please advise on what battery’s and controllers I will need for build I want 80plus volts kind regards thanks
DAYUM!!!! I wish you lived near me!!
Can increase speed?
What about this combination: 2 motors, 2 controllers, 1 throttle handle?
that's what he did lmao
Hi, would that work with the signal coming from the pedal Assist sensor instead of accelerator?
Can my 36V throttle work on a 48-volt controller/battery for an e-bike?
usually the throttles are are only 4.2v
No… you need a 48v throttle or it will blow the sensor as soon as you give it juice.
I have two identical motors and a controller that have the option of driving backwards and electric brakes on how to connect. Thanks for the reply.
I háve scooter 250w ecs IF put two bateries on 36v + 36v? Demage esc or ?
Hello. Your video it really great. But please tell me if i have two controllers but there is the option of three speed witch. How do i connect the wires ? do you think i can use one switch wit three speed option to connect two controllers together ? or i need to have a second switch ? an connect them separately ? thank you for your help an answer.
just use Flipsky VESC6.6 its a single controller for two motors can be use for different types of electric ride like skateboard escooter ebike
When you say 3phase wires to 3phase wires meaning from one hub to controller?
Yes, each hub to each controller
how did you install the wheel on the table?
How long will the battery last with this setting?
I am also wondering about that...in my dual motor scooter I upgraded my 52V battery from 20 Ah to 26ah but my bms overheats and has to be replaced constantly........
Is it a 48V battery fully charged or is it a 52V fully charged? Each battery will be alot higher voltage when fully charged your BMS is not up to the job get a higher rated BMS and add a heatsink to keep it cool
hello, can I also run two motors on one shaft,
thank you,
I think it will be with some adjustments
Do the controllers need to be identical?
I just bought a new scooter and the single motor works but when I try pressing the “Single dual” only 1 wheel works
Very nice video
É possivel amigo uma única controladora controlar 2 motores ?
Hello I have been doing this same test on my scooter . I noticed with my two controllers that are 48v 1000w that only the assist controller has self learning wires. So I can get self learning speed up to work with 1 wheel like u did in ur video. What about self learning on the main wheel. So we can get the low torque right on both wheels.
Onde vc comprou
Hi!! How can i add more speed to my scooter with 48v 18ah battery, 800w dual motor(2200), it run at 25kmh but i need more speed..shoukd i change my motor to higher watts or should i change my motor controller?
I think u need upgrade controller and battery to 60v
Cut the speed limiter wire
Why didnt u show how to wire everything up? 😭
Correct
Exactly. Sucks.
do you try 60v ? i like to get speed !
Will two motors, controllers and two batteries give me more distance ?
Yes but you better off just getting a bigger motor and more batteries
@@thatguy7612 I already have a 48v 20ah battery. I could not fit a bigger one. Plus i really like that it will bring me up a hill easily.
Do you have complete diagram of this including all accessories like brake,turn signal,brake lights...thanks
Each controller have diagram. U can search google or using manual of your controller
@@Laamlee-yt this is NOT TRUE. lol
@@Mike_Greene some controllers have sticker on wires stating which connection it is used
@@von9794 this is true. Keyword being "some" lol
Hoàn thiện xong xe chưa bạn ơi.
Chưa bạn ơi, cách ly xã hội mấy chỗ bán đồ nghỉ ko có đồ làm. :(
@@Laamlee-yt Trc mình chế nghịch cái 3 bánh cho trẻ con chơi cũng chạy 2 ic riêng. 2 bánh sau lấy nguyên bộ giá đỡ của xe cb, còn trc là xe đạp trẻ e. Đợt này muốn làm thành scooter mà cũng bị thiếu vật tư. Sợ nhất kiểu chưa có exp mà đang làm mới biết thiếu gì chạy đi mua giờ này mới khó.
Can do this on one brushed motor and one brushless motor?
I think can not
@@Laamlee-yt I think I'll just separate the controll and battery, but brushed motor on rear, and brushless on front.
I mean with 2 different controllers and motors, the speed will not sync if running at the same time, resulting in waste of energy. Of course it is possible to use only one of them
@@Laamlee-yt thanks for the input
Hi, I have e scooter with BLDC Hub Motor 800w of a 48V 21A battery, my problem is it can't go uphill with over 17 degrees angle, how can I go atlease 35 degrees angle uphills?
U can add one more hubmotor to become 2wd, or replace current motor and controller to at least 1500w.
hello, i'm planning to build an electric scooter, i will buy scooter frame, 2 48v 500-1000w motor and 2 48v 500-1000w controler, does a single throtle dsiplay work with 2 motor at once? and will the 3 speed mode will work? please help me
Si te funciono?
It would have been better to explain in voice what he was doing. Plus it would be better if he used two throttles so he could use back wheelbthe front would not be working until he used other throttle. Or the other way take taping of throttle wire from controller and put a switch in line. That would give instant speed from front wheel two throttle is best. Like the top gun bikes they have one thumb and twist
Hiya I have got Dual 2 motor electric Scooter 1200watt but the problem no Speed Control just handle like motorbike just up and Down roles So please can you let me how I can Change the handle and I can send you a photos for the Electric Scooter thanks
It is possible to do the same but that a controller does not have a trottle, it simply takes care of obtaining energy. Is it possible that controller A can draw power from the battery at the same time as controller B recharges the battery? Could there be a problem? Thx
@Diego Vidal yes you can do that but it's totally useless, the efficiency of the regenerative breaking would be less than 99% and around 75/80, completely useless
Hm kaya aabutin I'm using mober kasi plan ko gwin dual hub for additional speed kc 36v 8ah lang sya additional batt sana plan ko and gwn ko dual hub possible kaya? And san po location niyo kayo po ata yung nag post sa marketplace
How do youcconnect two controllers 5ogether?!?!
What is the voltage and amperage of the battery please?
Full kitt prices
Full kitt price
👍👍👍 ))) ✌
Just imagine 500watt two motor on fat bike unlimited fun.
Two speed controller green line connect speed Handel green line
A cho e hỏi,2 bánh xe cân bằng 20cm,2 ic điều khiển 24v 350w với bin,nhiêu dậy a
trên shopee bán nhiều mà e. ic tầm 200k~300k 1 cái. Motor 4~500k, e mua loại có sẵn dĩa chế cho khỏe, pin thì tùy e muốn đi xa hay quanh quanh chọn dung lượng cho phù hợp
@@Laamlee-yt bộ tầm cở 2tr,2tr mấy,bin di cở 7 cây chở lợi,e lây bộ
😊😊😊😊
waiting for the Part 4?!
Comming soon dude !!! Because of corona virus affected my country, all works slow down :(
Hlo
Would have been easier to explain the process.
will this set up lower operation system temperature?
rất tuyệt vời
Show all next time
Hi
Hllo
Hey. Puedes. Ayudarme. Y. Te pago. Por. La. Ayudas.
Why do ppl make dumb videos that don’t show how the wires were all connected properly. They just show the results. 👎🏼
Why so many freaking wires, what are they all going too? Why does every single wire need to be conn3cted too something makes no sense.