SuperATV Prop Shaft Installation on Can-Am Maverick X3 | How To

Поділитися
Вставка
  • Опубліковано 11 лип 2024
  • Take a look at what it take to install one of SuperATV Heavy Duty Rhino Driveline prop shaft into a Can-Am Maverick X3.
    Our shaft utilizes at 4340 u-joint, shaft made of 4130 chromoly tubing, phased and balanced offering zero vibration. If you want to install a strong prop shaft this is the prop shaft you want.
    Order your prop shafts today:
    www.superatv.com/can-am-maver...
    #SuperATV #RhinoDriveline #BuiltForBattle
  • Навчання та стиль

КОМЕНТАРІ • 14

  • @dougcompton6207
    @dougcompton6207 3 роки тому

    good video

  • @schumif1champ
    @schumif1champ 4 роки тому +1

    What light are mounts are those and for what length light bar?

  • @ericlaplante2291
    @ericlaplante2291 2 роки тому

    rear fix yok has to be 180 with the front one even with the stock drive shaft???

  • @dougcompton6207
    @dougcompton6207 3 роки тому +1

    I think you meant to say rotate 90 deg.

  • @johnm.lashmit8855
    @johnm.lashmit8855 2 роки тому

    Something with the aligning of the shafts isn't making sense, by the way it's shown in the video the rear yoke out of the transmission is in the horizontal position and so is the front yoke but before front shaft went in it was shown that the front yoke had to be vertical which would've put the pinch bolt vertical also but when in the machine front yoke is horizontal putting both shafts in the same position. It was said they have to be 180 degrees off, 180 is half a turn which is still the same position, was that supposed to be 90 off, if so that's not the way the video shows it going to gather.

  • @renedelgado2789
    @renedelgado2789 Місяць тому

    Shouldn’t the fixed ears on the shaft be facing the same front and back?

    • @SuperATVMedia
      @SuperATVMedia  Місяць тому

      They should be clocked 90 degrees of each other.

  • @0531lilrock
    @0531lilrock 3 роки тому

    Love the driveshaft, hate the bearing. Being a solid mount with no rubber to isolate it the bearing and driveline noise resonates through the floor and entire cage. Very annoying.

  • @billyzkool1
    @billyzkool1 Рік тому

    I watched this video but there wasn’t a part about the stock rear slip joint being seized up taking 2 weeks a torch and a sawzall to get off ??? Lmao

    • @SuperATVMedia
      @SuperATVMedia  Рік тому

      Some installs can certainly take longer than others when parts are seized!

  • @mandytuning
    @mandytuning 4 роки тому +2

    A bearing that is pressed , hold with snap ring and need to be serviced i will not use the retaining compound loctite,with that much it willl turn in hell to remove it ,even with all the heat of the sun .

    • @ezekielgordon8852
      @ezekielgordon8852 3 роки тому

      Pro trick : you can watch series on flixzone. Me and my gf have been using it for watching all kinds of movies during the lockdown.

    • @boonebridger1674
      @boonebridger1674 3 роки тому

      @Ezekiel Gordon Yea, have been using Flixzone for since november myself =)

    • @jaxtynmartin2841
      @jaxtynmartin2841 3 роки тому

      @Ezekiel Gordon Definitely, been using Flixzone for since november myself :)