The front axle of the truck was broken, I was not confused and repaired it again
Вставка
- Опубліковано 30 вер 2024
- The front axle of the truck was broken, I was not confused and repaired it again
#the #front #axle #truck #broken #not #confused #repaired #again
The welding will usually create a fault on either side of the weld.
I agree with others, the structural integrity is compromised.
КУВАЛДА МИКРОНЬІ НА ГЛАЗ СВАРКА БЕЗ КОРЕННОЙ ПРОВАРКИ И СТРАНА ЛЕТИТ К КОСМИЧЕССКИМ ТЕХНОЛОГИЯМ Учись європа
У дюйма-пол дюйма не хуй перекос.
With the skills that the Mechanics generally show, I would have thought cutting out the old tubing and fitting in a new piece would have been better option
But i think its harder for them😂
That y they did this😂
No se deje , demandé y llegué hasta las últimas,ni que fueras un delincuente,aver qué pasó con los europeos que se dopan y las UCI le represalias toma.
Смотрел не отрываясь, мастерство высочайшего уровня.
Leggermente un po meglio del suo vicino dietro l'angolo allo stesso tempo suo concorrente. Diciamo per il momento abbastanza bene per l'età tua, hai tutta la vita davanti per imparare che alcuni pezzi bisogna cambiarli del tutto e non aggiungere canottieri, mutande, chiodi, calzini !!!
Pazienza
Another one of those "I think they call this welding" jobs...
People are very CLUELESS if they think that this is a good and adequate repair !
GL , good luck .
Thanks
What would be the right way to go about this job?
@@yandelyanoIn America there is not an acceptable practice welding on steering axles and brake components ! This axle was not even properly ground to accept a deep veed weld . The temper of this drop forged axle is ruined .
Use some gloves man. Avoid hand injuries.
Artesanato ? ? Isso é uma técnica invejável
Seria melhor,ter feito uma cavidade na trinca,com uma lixadeira,e preencher o espaço com a solda.Ficariaais volume de solda na peça
I am going to guess.or, speculate,, Could be stronger than original piece was.
Sorry, but #notbloodylikely..
The issue is loss of design temper / hardness of the axle, which was originally a one-piece forging. This repair will get them back on the road, and may hold up for a good while under light to moderate loads. But if they work it as hard as they did previously
It wont last very long
Under the circumstances- PERFECT.
Please, can someone answer me?
Why do these poor people work squatting on the floor, in the middle of dirt and garbage, without using workbenches, without personal protective equipment? Why don't they wear safety boots? Why do they wear such dirty clothes?
Porque no tienen la suerte de vivir dónde tú vives.
Have you ever noticed when they are reparing something ..no air or cordless tools 16 men with 16 spanners
Semplicemente così va di moda da quelle parti. Abiti più sporchi, più attraente sei.
كامل
Parabéns muito bom...
In most western country's this would be an illegal repair and would land the operator and the bogger (a bogger is someone who doesn’t quite meet the expected level of quality) in jail .When it fails I wonder how many family's it will wipe out
It is because of those western countries these people are forced to repair their vehicles like this. It is nearly impossible to buy vehicles parts, so either they scrape the vehicle or repair somehow.
Everytime the oil gets cheaper the west creates a war somewhere. When oil for dollar system is gone things will change.
Ni ce warning 😮
Because Western can't do sh*t can't repair like Pakistan
@@Ahmed_Nadeem @eddiephillips6740 doesn't understand that Western countries are part of the problem, if not the cause.
Стакой работой - безработица отсутствует.
ประเทศอะไรงานซ่อมแบบนี้ซ่อมเก่งมาก
Já assisti varios vídios , são muito bom no que fazem , só que estão sempre sem óculos de proteção .
"Repaired it again...". Says it all.
Hanging by the thread
ماشاءالله
Os caras são muito bons no quê fazem.👍
PERFECT.👻👻👻👻👻👻👻🥳🥳🥳🥳🥳
💯
You are pretty I like you
Slm hadir dari Malaysia amier
Should have used plug welds to
Fazem remendos e vao ao espaço, capacidade .
تابعت من البدية شغل ممتاز والله
We’re are the elephants .?
? ROSTSCHUTZ
Бълз
#
I have to say . As a one of. Bloody good Job ; 😊
You may think you did a good thing by making your own axle sleeve for the king pin on the lathe but there is a few problems. When you were done and put the king pin into the bore it looked pretty tight, is there going to be room for grease. When you get a new king pin set they come with a upper and lower brass bushing usually with nylon on the inside to hold the grease you pump into it. The sleeve you made is to tight and will never hold grease properly.
Вращаются втулки вокруг шкворня и там нужна смазка.
Шкворень в балке закреплён неподвижно специальным клином и смазка в этом месте не нужна.
Top 🇧🇷
nice!!!👍
NICE JOB
Muito bom 👏👏
Primitive but it works…
Muy buen trabajo pero terminan el vídeo y no se be si el pistón idraulico funcionó bien uno los be porque aprenden de ustedes hermanos
Wow. Well done.