good video, after 17 years I changed the bushings, I needed a 2 arm gear puller to free the spider. Also when you disconnect wires from the heater element, there is a white plastic piece. above it with a rubber hose plugged into it. remove this hose. It's the water level sensor. This is a rewarding job, but a time consuming one. It also saves you a lot of money. I would change shock absorbers and put new brushes in the motor while you have it apart. Make some notes and take your time
After doing all that work, which I admire you for doing, I wonder how long e.g. the Programmer will last. This may be why Miele say it's uneconomic to change the bearings. P.S. I wonder how much a new programmer would cost. These days you can of course design your own PLC based programmer if you're that way inclined.
Thanks!:)A little over an hour.But I did not at once but in stages. I took it apart the machine and then waited one day until the arrival of the bearings.
Wow I'm impressed! Only that I was waiting for the moment you would remove the door seal I don't know why but.... And know I need to look further how to take it out.
I don’t think you checked the inner drum spider... worth doing - I think mine is making mine off axis and rubbing on door seal (and this is causing rumbling noise). Bearing I think is fine. Apparently the aluminium ones corrode...
Your motor needs servicing. Replace the bearings and using a commutator stone helps. A better bet would be to replace the motor bearings, lathe the commutator until it is round and use a seating stone to help bed the new brushes in. It can be difficult to remove the pulley from the motor.
The motor bearings are not in bad shape.Were oiling.The commutator has been cleaned.The engine has been cleaned of excess coal dust.Only I did not show it!:)
I have a Miele 3035 washing machine. I pulled out the inner drum by accident, the drum was off axis and make a lot noise. What should I do? Please help me, thanks!
Szervusz! Szuper a video, koszonom a segitseget, pont ezt kell csinalnom a Mutterom gepevel. Add meg, legy szives, a csapagyak es szimering adatait, koszonom!
hej, use never a hammer to drill in the bearings whith an other hammer, the hammers may have the same hardness and will explose easly! beware. jean michelle jarre´s pop corn?
hej, use never a hammer to drill in the bearings whith an other hammer, the hammers may have the same hardness and will explose easly! beware. jean michelle jarre´s pop corn?
good video, after 17 years I changed the bushings, I needed a 2 arm gear puller to free the spider. Also when you disconnect wires from the heater element, there is a white plastic piece. above it with a rubber hose plugged into it. remove this hose. It's the water level sensor. This is a rewarding job, but a time consuming one. It also saves you a lot of money. I would change shock absorbers and put new brushes in the motor while you have it apart. Make some notes and take your time
Please help me!
How much kg of clothes can it take? I have searched all over the internet, but nothing.....
@@ritarajczi6132 5 kg / 47 litre volum
After doing all that work, which I admire you for doing, I wonder how long e.g. the Programmer will last.
This may be why Miele say it's uneconomic to change the bearings.
P.S. I wonder how much a new programmer would cost. These days you can of course design your own PLC based programmer if you're that way inclined.
Thanks!:)A little over an hour.But I did not at once but in stages. I took it apart the machine and then waited one day until the arrival of the bearings.
Took me 10 hours
Really interesting - Thank you.
I hope the new bearings last as long as the original Miele one's.
Holy macaroni, you took out the whole thing. I have a Miele W 149 toploader. I hope i won`t have to take the drum out when replacing the bearings.
Wow I'm impressed! Only that I was waiting for the moment you would remove the door seal I don't know why but.... And know I need to look further how to take it out.
I don’t think you checked the inner drum spider... worth doing - I think mine is making mine off axis and rubbing on door seal (and this is causing rumbling noise). Bearing I think is fine. Apparently the aluminium ones corrode...
Well done but I could hardly see anything.
Hi!, very good video!!, In the past my grandma had one (the grandma who has the bosch), they are a very good washer, Thanks for uploading this vid!!
Your motor needs servicing. Replace the bearings and using a commutator stone helps. A better bet would be to replace the motor bearings, lathe the commutator until it is round and use a seating stone to help bed the new brushes in. It can be difficult to remove the pulley from the motor.
The motor bearings are not in bad shape.Were oiling.The commutator has been cleaned.The engine has been cleaned of excess coal dust.Only I did not show it!:)
I have a Miele 3035 washing machine. I pulled out the inner drum by accident, the drum was off axis and make a lot noise. What should I do? Please help me, thanks!
Where is the inner drum spider ?
Szervusz! Szuper a video, koszonom a segitseget, pont ezt kell csinalnom a Mutterom gepevel. Add meg, legy szives, a csapagyak es szimering adatait, koszonom!
Szia!fejből nem tudom de ha kiveszed úgyis meglátod.
Can you please help, I can't seem to knock the drum right through the bearings?
Уточните модель или модельный ряд Miele, с силуминовой крестовиной. С уважением!
Good! I do it now also with my W723 :-D
Wow. That was a great job. Thanks for showing us :)
hej, use never a hammer to drill in the bearings whith an other hammer, the hammers may have the same hardness and will explose easly! beware. jean michelle jarre´s pop corn?
Yes,the music is pop corn.
Good stuff, better than my bosch 2008 model with plastic water drum outside , a mega job complete demontage of all units. ?.........
Yes.
good video, but too fast to follow
как называется музыка?
Pop corn
Its like bauknechtboys style
Good video to fast to follow
You took one hour then you must know what your doing then pal.
Thanks!:)
it's verry good vid's!!!
😎
fucked up sounds
Des Video is ve de Fisch do sixt nix wos a duat
Wie Sie sehen, sehen/sahen Sie nichts...
hej, use never a hammer to drill in the bearings whith an other hammer, the hammers may have the same hardness and will explose easly! beware. jean michelle jarre´s pop corn?