Improved your health, repurposed landfill material, reduced your carbon footprint as well as anyone else's who was involved, and still saved money. FANTASTIC! Good job!
great Idea for the solar charge controller, It gave me the Idea to change my "Fisher and Paykel Cycle" over to a 3 phase wind turbine charge controller and get rid of the bridge rectifier board and variable output to keep an eye on. Thanks Cobber.
Impressive! absolutely the BEST I've seen! I'd buy one of these if they were on the market. Thanks for sharing!...also, sorry that you have to put up with so many really stupid comments...wow.
Hi Hunwick, I was just wondering, where did you get the drawings of all the wiring's and if you know where I could get all the specs on this motor? The actual website only gives some of the specs.
I am not sure but I think if you use a capacitor bank parallel to the battery, you won't need the fly wheel and it won't matter the voltage you crank out either.
You can turn this into pedal powered welding machine if you use a heavyweight flywheel and rewire the motor to have all coils in parallel. The user would pedal for a minute or so accumulating the energy that will be used in short bursts (the welding draw huge current) What do you guys think?
Maybe put a voltage regulator so it holds the voltage between the red marks no matter how fast you pedal. and maybe if you pedal faster you get more amps.
I think that if you used a mass wheel with a larger diameter (1.5metres) would be a better effect, accelerating such a wheel would certainly increase the effectiveness of this device
if you can transfer your energy horizontally onto a really heavy disk gear, that steps down into a generator spindle. you can get off your bike and the thing will keep spinning, the speed of the large disk will be slower than the smaller one attached to the generator (which is good more RPM) does that make any sense? its like an old school pottery wheel
EvendimataE Ha haa! raising a child is not difficult. You put the kid on a street corner and you leave it there. You come back a week later and if the kid's still there, you got yourself a stupid fXing kid. Then you proceed from that point. Kids are like any other group of peoples. A bunch of winners and a hole lots of losers :)
From what I understand, If batteries are left on the ground too long ,the cold of the ground causes condensation inside the battery causing it to eventually fail.
this is a great video and inspirational design, I wanted to do something similar before something got in my way......how hard do you have to tread for the 4 amps you are getting? If you used the same rotor/stator for windenergy, would you wire it different to avoid cogging and adjust the output voltage to the speed? Which kind of RPM are you getting? Cheers!
Really fantastic! Everyone should think about doing that. Can you please inform us of exactly what parts you used and where you got them and a price breakdown?
+darkmath100 You would lower the resistance. The higher the resistance = the easier it is to pedal. It's counter-intuitive, I know. However, this is because R=V/I. Cheers
i want to make one of these with a HUGE flywheel. Like 5 feet in diametre and a foot thick. (concrete project). I have a pottery wheel with a 4 foot wide by 2 or 3 inch thick flywheel on it, and it spins for a hell of a long time.
Ok now with an excersize bike the spinning wheel is designed to induce drag for the excersize to burn calories, provide resistance. I can see you have the fan type that produces air resistance. You should replace this with some weigh (Ok i didnt get to that bit, the teeth give it air resistance) so it will continue to spin after you stop pedeling.
It looked like he was generating 4 - 5 amps on 12 volts. Less than 0.1 kW. It would keep a notebook computer or two running for an hour. An average bi-cyclist can not keep up with 1 kW moped, which would produce 0.5 kW electricity.
Not bad mate. But try a 10 speed or more bike add two 100 amp car alternators to the back wheel with the cars voltag gauges and two 800 cranking cold amp batteries add a 6000 watt inverter and you can power most of your Houston and shed off the pounds at the same time . I have the planes
The pedal power alternator is just the first system component. Why do we have to stay stuck in the dark ages? There used to be one execise bike that used an alternator. Patent blocks I bet.
I don't think so. Fact is, the average person would be hard put to produce 125 watts continuously. What with losses ans so on, one might count on 50 electrical watts output. That's OK for some electronic devices.
i say this is great parts for makeing a generator but i have far more advanced ways to keep it running without gas. or a system that turns on off even car alternators what ppl dont know you can do to/ with them, for either 12vdc or ac or 120vac or 220 . did you test at full output? what volts amps with /without load what type of load ? . one thing to keep in mind many coils of same size wire will give more volts .thicker gauge wire will give more amps. 1 phase or 3 three will serve best for heavy loads single is best for light load . peace.
اسعد صالح الذي فهمت منه انه استعمل موتور غسالة قديمة من نوع معين و بعدها قطع الأسلاك مثل ما في الصورة و تم توصيلها بشكل معين، ابحث في الانترنت عن الموقع الأسترالي لانه هذه الفكرة أنا شفتها على موقع استرالي في ٢٠٠٩ و رح تعرف اسم الموتور و طريقة توصيل الأسلاك. ان شاء الله تكون استفدت
It will your kindness if you could supply me this motor with alteration to generator with exl so I could could show my student for understanding its function. . Tell the price 27 Fenmere Close Wolverhampton UK. if you are in west midland I can come to collect. Regards with Happy New Year 2015.
+Dr Sharma You can probably find one of these at an Appliance store that offers to scrap you old washing machine when you by a new one. I work a part time weekend job and it took about a year and a half, but I finally found one!
Improved your health, repurposed landfill material, reduced your carbon footprint as well as anyone else's who was involved, and still saved money.
FANTASTIC! Good job!
great Idea for the solar charge controller, It gave me the Idea to change my "Fisher and Paykel Cycle" over to a 3 phase wind turbine charge controller and get rid of the bridge rectifier board and variable output to keep an eye on. Thanks Cobber.
Looks really good! I wish Tesla made a version of this and put it in stores.
Awesome video, thankyou for putting in the effort of showing the printouts of how it goes.
Impressive! absolutely the BEST I've seen! I'd buy one of these if they were on the market. Thanks for sharing!...also, sorry that you have to put up with so many really stupid comments...wow.
Hi Hunwick, I was just wondering, where did you get the drawings of all the wiring's and if you know where I could get all the specs on this motor? The actual website only gives some of the specs.
Follow up vid I wanna see these 10 amps! even 8 would really cool you must show us your man power in this brilliant generator.
Can you explain the different wiring configurations and what are they useful for? Great job btw👍
I am not sure but I think if you use a capacitor bank parallel to the battery, you won't need the fly wheel and it won't matter the voltage you crank out either.
You can turn this into pedal powered welding machine if you use a heavyweight flywheel and rewire the motor to have all coils in parallel. The user would pedal for a minute or so accumulating the energy that will be used in short bursts (the welding draw huge current) What do you guys think?
Adler Mow using bank of capacitors in conjunction with batteries maybe ? Then through inverter if necessary, I may investigate this idea
Maybe put a voltage regulator so it holds the voltage between the red marks no matter how fast you pedal. and maybe if you pedal faster you get more amps.
I think that if you used a mass wheel with a larger diameter (1.5metres) would be a better effect, accelerating such a wheel would certainly increase the effectiveness of this device
if you can transfer your energy horizontally onto a really heavy disk gear, that steps down into a generator spindle. you can get off your bike and the thing will keep spinning, the speed of the large disk will be slower than the smaller one attached to the generator (which is good more RPM) does that make any sense? its like an old school pottery wheel
kids computers should be powered by something like that...if they dont pedal they cant play games or go to facebook
EvendimataE Ha haa! raising a child is not difficult. You put the kid on a street corner and you leave it there. You come back a week later and if the kid's still there, you got yourself a stupid fXing kid. Then you proceed from that point. Kids are like any other group of peoples. A bunch of winners and a hole lots of losers :)
From what I understand, If batteries are left on the ground too long ,the cold of the ground causes condensation inside the battery causing it to eventually fail.
this is a great video and inspirational design, I wanted to do something similar before something got in my way......how hard do you have to tread for the 4 amps you are getting? If you used the same rotor/stator for windenergy, would you wire it different to avoid cogging and adjust the output voltage to the speed? Which kind of RPM are you getting?
Cheers!
I always heard to keep the batteries off the floor and ground. Will batteries slowly discharge if left on concrete or dirt?
Really fantastic! Everyone should think about doing that. Can you please inform us of exactly what parts you used and where you got them and a price breakdown?
Wonderful Job !
How would you change the resistance to the alternator to simulate going up a hill for example?
+darkmath100 this can be achived just changing the electric load. Any alternator runs ligh if there isnt load, becoming harder as the load increase.
+darkmath100 You would lower the resistance. The higher the resistance = the easier it is to pedal. It's counter-intuitive, I know. However, this is because R=V/I. Cheers
i have a pace maker will it work attached to this device
Duuuuude!
At the end of the summer your kids could tackle Tour de France.
that is freaking awesome!!
Where can I get a motor like that?
props for your hand-wound coils.. you wasted a TON of time.
❤😂🎉 allsome work from cruzermans inventions 😁👍🦇
I guess there is speed and then there is power? how fast can you bike vs how much can you carried by bike?
That is beautiful!
Hey an alternator or auto electronics system is more readily available?
Does it matter which direction it turns? Clockwise or counter clockwise.
Ty
Wishing I owned a supercapacitor factory so I could send you a gross to mount to that pony.
¿como solucionaste el frenado del campo electromagnetico cuando entra en consumo?
i want to make one of these with a HUGE flywheel. Like 5 feet in diametre and a foot thick. (concrete project). I have a pottery wheel with a 4 foot wide by 2 or 3 inch thick flywheel on it, and it spins for a hell of a long time.
how many voltages is this bicycle producing when pedalling fast? can it run my kettle for making tea on a camp site?
What machine in the us would be the best for this project
Ok now with an excersize bike the spinning wheel is designed to induce drag for the excersize to burn calories, provide resistance.
I can see you have the fan type that produces air resistance.
You should replace this with some weigh (Ok i didnt get to that bit, the teeth give it air resistance) so it will continue to spin after you stop pedeling.
How much average power could be generated in the pedalling for 1 hour?
It looked like he was generating 4 - 5 amps on 12 volts. Less than 0.1 kW. It would keep a notebook computer or two running for an hour. An average bi-cyclist can not keep up with 1 kW moped, which would produce 0.5 kW electricity.
Hey Good job!
I would like to know what can of wiring you recommend for a 12 volts’ battery setting?
7x2c is your best for low rpm.
How long w ould this take to charge 1 flat car battery? Say, from a corolla.
Not bad mate.
But try a 10 speed or more bike add two 100 amp car alternators to the back wheel with the cars voltag gauges and two 800 cranking cold amp batteries add a 6000 watt inverter and you can power most of your Houston and shed off the pounds at the same time . I have the planes
michael lennon 810858769 I wanna learn how to do it I’m from flint mi I wanna start my grow house HMU bro please
can we store this electricitu to use later?
Is it possible to use the motor on a normal bike for a easier ride? Rather than using a battery to power the motor.
You indicated that the motor is "rewired". How is it rewired?
I assume we were watching the same video .... he explains that 3:40 along with several other possible configs.
may i know if what brand of washing machine that have motor like this you use? thanks
Fisher & Paykel smart drive
Good day, how much volts and watts can you produce?
What is the ratio between gasoline engine hp to output wattage of the generator? Thanks.
+Olejo111 depends a v 4 could generated hundred of hp, avg 160 hp.
The pedal power alternator is just the first system component. Why do we have to stay stuck in the dark ages? There used to be one execise bike that used an alternator. Patent blocks I bet.
I don't think so. Fact is, the average person would be hard put to produce 125 watts continuously. What with losses ans so on, one might count on 50 electrical watts output.
That's OK for some electronic devices.
@@BasementEngineer That could be enough to run the TV for watching the soaps while peddling off the excess fat.
@@nixeco You are right on that.
Everything is great, you know... Just one problem, you'd need to insulate it...
How fast and what configuration would the wife need to use so that us blokes can watch to foot ball game on the Television during the next Barbecue ?
You'd need a harem.
how would you tie this to the grid?
why not have an inverter?
where did you get that generator?
i say this is great parts for makeing a generator but i have far more advanced ways to keep it running without gas. or a system that turns on off even car alternators what ppl dont know you can do to/ with them, for either 12vdc or ac or 120vac or 220 . did you test at full output? what volts amps with /without load what type of load ? . one thing to keep in mind many coils of same size wire will give more volts .thicker gauge wire will give more amps. 1 phase or 3 three will serve best for heavy loads single is best for light load . peace.
How many watt in an hour ??????
can I have a parts list and cost on this?
I suppose human pedal power is what 0.3 hp?
you could make an exercise bike out of that generator
Sweet! Now put the kids to work we need some toast.
nice man bravo for idea great
does this produce dc or ac?
Try putting ac into a couple lead acids youll figure out real quick
oooh in case you wana go through time you first need to get to 88 mph lol.
very good
Original very! God Idea!
check out how slow it spins. its perfect for wind power!!
thats genius... need to build before zombie apocalypse XD
Please take the time to visit Witts period ws to see existing solutions for free energy and talk with the experts who can help you implement them.
more information about this topic please
اسعد صالح
الذي فهمت منه انه استعمل موتور غسالة قديمة من نوع معين و بعدها قطع الأسلاك مثل ما في الصورة و تم توصيلها بشكل معين، ابحث في الانترنت عن الموقع الأسترالي لانه هذه الفكرة أنا شفتها على موقع استرالي في ٢٠٠٩ و رح تعرف اسم الموتور و طريقة توصيل الأسلاك. ان شاء الله تكون استفدت
Giovani Capitanio
اسم الموقع
www.thebackshed.com/windmill/articles/coglessFP.asp
outstanding!
i saw a bike using a car alternator connected to a battery connected to a dc tv for the kids to watch
Super
brilliant ty for sharing =)
great idea.
now, make one with a low gear ration. tesla turbine. and solar mirrors to make steam... mega power
+INVISIBLE SUN low gear ratio, not ration, thank you.
lol my spelling 10/10
the Batteries are on the ground....
that's awesome
top stuff
way against unemployment?
Build a Hoover craft, :-))
This is what a real peace prize ought to be given for❤🦾☮️✌🏾🚲
I'll never understand why someone would try and explain something my waving the camera around and talking in circles about nothing.
selbstgebautes Ergometer mit LG Waschmaschinenmotor!
nice
It will your kindness if you could supply me this motor with alteration to generator with exl so I could could show my student for understanding its function. . Tell the price 27 Fenmere Close Wolverhampton UK. if you are in west midland I can come to collect. Regards with Happy New Year 2015.
+Dr Sharma You can probably find one of these at an Appliance store that offers to scrap you old washing machine when you by a new one. I work a part time weekend job and it took about a year and a half, but I finally found one!
Use that engine and build an ultralight
Revelation 14:12
(King James Bible)
Here is the patience of the saints: here are they that keep the commandments of God, and the faith of Jesus.
Neat but I prefer dog power
i like turtles
Good work, however. very little amps and Wat dynamo. high speed. 190 Amp 150 rpm dynamo. See Enter my video
Josdd
If you email me direct at tonyl.multimedia@gmail.com I will send you some info that should answer your questions.
Show
thats dilldoe
and them he will found the energy source of the fantasy island. please learn science, phisics and math. regards lol
and you learn how to spell!
@@EE16SVT Let me time , English its my third language Lol !!!!
This makes me tired