The spring was definitely the most difficult part and had to get my wife to help. I followed the video and got the job done in 4hrs but took quite a few breaks along the way. I made up my mind before beginning the project that I was going to be patient and that paid dividends. Don't start this unless you have ample time. Drink a couple while you do it but not too much. Saved big bucks!!!
Man, I have been on this for 5 hours now. Drank several, cussed, drank some more. Taking apart AGAIN because it was leaking after I had it all put back together. The spring is by far the hardest part to do. I think I've drank enough because I'm laughing I stead of cussing now...
I do 2 a week in an apartment building and for customers it take 15-20 mins max step 1 do not remove anything you need 2 large clamps the squeeze kind also lubricant the boot b4 you put it on the tub stretch the rear spring about 1-2 inches it will still hold as you put the spring around the rear boot use the large clamps to hold it in place starting at 12 o’clock fold it inside the tub so you can use the clamps
Just did this as well. Thank you for the video. I agree the retainer spring was very hard and the two wedges provided not nearly adequate. Do what I did, go to the hardware store and buy a 3/4" x 48" wooden dowel for 2-3 bucks. Have them cut it up in 4" chunks and use those for wedges while going around. Double up on the wedges so friction is helping you out.
The toughest part of the whole replacement is getting the rear coil spring back on. I read the comments below and knew it would be tough, then spent about 15 minutes trying by myself and getting frustrated. With an extra 2 helpers it only took about two minutes, HIGHLY recommend this approach. Started to put the spring on, put a AA battery at the 10 and 2 clock positions. My wife then held these two firmly in place so they wouldn't slip. I then stretched the spring out from both sides and my other helper used a small wooden dowel (almost anything will work) to work the spring into place from the 3 to 9 positions. Worked great and went fast.
Absolutely the perfect solution, they are the perfect size, I used about 8 of them and it only took 5 min to install... Oh, also turn the boot inside out into the drum, gets it out of the way. Cheers!
Struggled for an hour before I found this comment. Using AA batteries was the perfect solution! Thanks!! The extra space at the counterweight mounting points was the perfect place to insert the battery then slide it to one side to lock the battery and spring in place. With the battery securely wedged, it allowed pulling spring tension As You Go much easier. Without pulling as you go, you won’t have enough left for the final effort. I only needed three batteries as I could pull the middle one and use it in the next space. Less than 15 minutes with this method.
Doing it this way is needlessly complex. You can replace the boot seal entirely through the front door of the washer. I did so myself having never done it before (I did take the front door off the washer to give more access to the boot seal, though). I'd heard this long, convoluted method wasn't necessary, and so gave the simpler method a try. It worked fine and no leaks after 3 weeks of use. (It was so easy to do, in fact, my wife volunteered me to do it again in a few years when the mold builds up again.)
As old as this video is, it's still relevant. Easy to follow step by step instructions. I completed this job today, which saved me $300 that I was quoted.
That was very challenging! The video was extremely helpful to see the steps, but I agree with one of the comments below that they quickly jumped to the end of the step with putting on the retainer spring because it is SO HARD!I do think this video makes it look deceptively easy. I finally got it after about 90 minutes and my fingers are raw. Here was my technique in the end... Get that first spring retainer thing wedged in there as well as you can. Keep checking on it and banging it in as it'll slip out. if you can get another person to check and hold it in, that might be helpful. Also, I think it helps to make sure that it's not sitting on ANY of the rubber, so it was pushing the rubber in toward the center and the spring a bit. I found other tools that I could wedge in there every few inches which helped in places, but one key is not to lay the spring slack from the first retainer to the next - stretch it as much as you can (even if you don't need to for that first bit) at the beginning and that'll make it easier in the end. I also found a pair of pliers which was the right size to wedge in sideways which helped to push the spring down and into the groove. Finally, I'd say work pretty quickly if possible. The slower you go the harder it is because you tire out and also the retainers slip, but until you get a good technique, I admit, it's really hard to work fast. I failed and cursed quite a few times before finally getting it... Good luck!!
These tips are all great. The spring is hard, but doable with two sets of hands. Have someone hold down the retainer things for you, and then basically work as fast as you can.
Do some washers have different mechanisms to the spring lock , like a clamp with screw ? I think my Miele might have this clamp screw lock for the inner spring , I’ll check on it. I will not let this job defeat me!
Thank you for actually showing to use the clamps instead of those crappy place holders that come with the kit. The other videos on this cut away as the guy gets started on putting the interior spring ring and then cut to him all finished. Putting that first spring ring on is the HARDEST part of this, but you made it easy! Thanks!
Wow. Thank you so much for the video. I am a handy guy, but that inner spring is a huge pain! What worked for me was about six steel spring clamps with rubber padded tips that you can get at HD/Lowes for $1/each. I would get about 1/8th of the spring on, use a clamp, stretch on another 1/8th of the spring, another clamp, and repeat. It was still a pain and my thumbs are raw, but it can be done!
Awesome video - thank you. Replaced mine today, no issues. The hardest part was of course reinstalling the rear retaining spring. I first put those plastic retainers at 12 and 6 o’clock and secured them to the frame with nylon cable ties. Then stretched one side and fitted it into place, then the other. I am going to dry this one off after every wash - hopefully that will prevent the ugly mold. Thanks again!
The whole job took me about an hour to remove and replace my seal. I didn't need any clamps or the special tools as it all went pretty easily with brute force lol. Thanks for the help!
Great video! I knew the spring would be a beast so after 10 mins of battling, i took off the front counter weight and had plenty of room to easily install the spring. Saved a lot of time, frustration and patience with that. Thank you for the video!
Thank you very much. Even though these washers aren't worth fixing, you at least made it possible for those of us who are foolish enough to try. When it comes to installing the inner seal, drench and I mean drench it in lubricant, I ended up having to use WD40. Good luck to those who try.
Hey guys thanks for the video! Couldn't have done it without you. One tip I have for the large spring is to stretch it a little. I stood on it and pulled up. Maybe pull in small sections. I may have stretched it too much. One question/ issue I have after completing tho is my door didn't shut as well as it used too. Luckily it locks when running so it doesn't pop open. Thanks again!
I have a tip for everybody for that innerspring because it's pretty difficult. You have to take the whole face of the washer off. Anyway I used two clamps, I started at the top( my washer had an indention on the boot behind the arrow that you snap into a tab at the top of the rim of the washer seat when I was mounting the boot) anyway , get your spring seated and put first clamp on very tight (at 12 o'clock) and work your way counterclockwise. After you get about 1/3 of the way or about 8 o'clock, put the second clamp on but it is very important while you are doing this TO KEEP TENSION ON THE SPRING (KEEP IT STRETCHED OUT AS MUCH AS POSSIBLE) Now with the clamp at 8 o'clock keep working your way to about 5 or 6 o'clock. Then move the 8 o'clock clamp to 6 oclock(left side of where you're pinching) then just keep workin it!!!, I did it by myself but two people would be easier. Make sure you keep tension on the spring until you get half way around( I think I kept tension on it longer so maybe just don't let up until your arm gives out) . Then you should have enough to muscle that cock sucker in there (excuse my French)lol. I used a flat head screw driver for the last 20 percent or so because the folded boot can get in the way. I hope this helps
Brendunt Scott You do not have the reply feature turned on. Clean everything as best you can, I am not sure baking soda will kill mold you might try bleach. You can also run some Affresh through it to help clean the inside. It is available on out website, part number: AP4308494.
I used some sockets that were just thick enough to stay in place. Harbor freight 7/16, 3/8 drive sockets did the trick lol. I used 2 of them. And found it easier to start at the top, then move the holders (sockets) down as I got more on, but you really have to pull and stretch the spring as you put it on, or you'll over extend the spring and ruin it. Once the spring is a little over half way on, I found the only way I could get it o was to pull it with both hands down, and over the bellow. Then sort of pull the bellow down hold it, while I used other hand to roll it into the channel until it finally snapped down in. Very tricky to install, but was able to figure it out.
Really easy to put back inner spring if you take out the front panel and have set of at least 3 rubber big clamps (I got at HomeDepot for few dollars each). I used one of those auto mechanic clamps which forms a hole at the end when you close it and use that to drag the inner spring around gasket. Also make sure to use soap. Huge difference. Doing all this, it took me about 20 mins to do the versus trying for hours previously.
Just finished mine 10 mins ago and I can see how it can be a pain but mine went in like butter. So a few things defiantly use dishwasher soap I mean pour it on. Another thing I did was I had a heat gun and went around the areas that I was working with. When I first tried it without the soap and heat I couldn't get the thing to even start a seal. Once I lubed it up and just heated a section at a time and got it started it just slid in.So overall great video and since you just saved yourself about 50-100 bucks labor go do something fun tonight with that cash you just saved.
I just did it by myself and I'm a small dude. Lol. But I literally had to keep 20 lbs of muscle tension on the spring for the 15 minutes it took to put the inner spring on. My forearms were numb for a bit. 😂
So incredibly difficult. That tricky editing makes it look way to easy. Plan on at least 2 1/2 - 3 hours on this project. Key thingsMore soap! 4 -6 Chapsticks wedged in sideways, the full length of the chapstick for 1st spring retailer. The plastic “tools” they provide are practically worthless. Jumbo office binder clips for the second spring retainer. Attached binder clips as you work the spring around the boot to hold it in place. This made all the difference after many failed attempts. Good luck!
This can be a lengthy process, and our editing process does cut out lengthy/repetitive scenes like unscrewing screws, so repairs generally do take longer than the length of our videos. Thank you for those tips.
The video was very helpful. The retainer spring was difficult. I had my wife help me, with an extra set of hands. Could not have done it on my own. Once again, thanks, you saved us a lot of money. :)
First, I did not remove the top or front pieces as described in this video, as others have said it wasn't necessary to do the job. Would it have been easier to do? Not sure. I did this gasket/door boot replacement on my 2005 Kenmore front loader last week. The toughest part by far is getting that inner spring to go around gasket without popping off, even with the supplied retainers. I had to get my daughters help and we finally managed to get the spring on. It's definitely a struggle, but I was determined not to pay a service tech to do it. :-). The rest of the job is easy. One other note; there was a lot of crud (for lack of better words) around the washer drum and the plastic rim that the inner boot goes onto. I took some time to get as much of it out/cleaned as possible. You might want to check yours and do the same. I'm in Canada and paid $282 with tax for this part. Was pretty shocked at the cost considering it's basically just molded rubber. I think my next washer will be a top loader again. Then you don't have to worry about the rubber boot needing to replaced.
282 is absolutely ridiculous, even if I purchase this in the US, I'll be out over 100$ which I'm still rolling my eyes about. i expected about 60$ or this part. I'm ordering my part today, thanks for the Tip.
Yeah, couldn't believe the cost. Might have been able to get it a bit cheaper, but was in a rush to get the job done so got it from a local store here within a day. Also, make good and sure you're getting the right part. They new part is an improvement over the old for sure. Good luck with getting yours replaced.
Just did it myself with the help of a friend. Until I removed the front and top panel, I couldn't even get the inner spring out! Removing the front panel allows for much more space to work with. Would recommend. Also, the it's almost impossible to get the inner spring on with only two hands. retainer thing keeps popping off. You need at least four hands stretching the spring four ways. Last bits, use a flat-head screw driver to ply it in.
I found the same thing...you need an extra pair of hands to keep that inner spring from popping out. What make of washer do you have? The one in the video here is a Fridgidaire....mine was a Kenmore and is slightly different in design.
Yikes. Just paid $113 usd on Amazon for this. Also got a new outer ring for $24 as mine was rusty. I really wish that one little plastic tye for the top hose was included. It costs pennies but now I have to take a trip to the hardware store 😒. Wish my luck, guys.
I found this video helpful. Took me about 20 min total to change the seal. Putting the inner spring on is the hardest part. I found the retainers worked well. Bye bye old nasty seal ;)
Thank you for the video - for those shore doing this alone - go and get yourself 5-4 padded clamps at Home Depot 99 cents each - you ll be done in 5 mins
A note, the earlier model of these washer do not allow enough room for the spring retainers, watch for them flying out at your face while you stretch the spring.
The spring retainers provided are not adequate and I’m not sure how it was possible you were able to install it without additional items. The amount of tension on the spring is enormous. A more realistic installation of that spring requires two or more clamps and a long shaft flathead screwdriver to leverage the spring around the boot.
If the sprig retainers don't fit between the weight and the tub what can I use to hold it in place. This is infuriatingly difficult. Frigidaire gallery 10 years old.
Really very Thanksm y friend, very helpful. Only one question.., All the machines, works in the same way..? My wife's machine is a Samsung, and the ruber is become dirty and black, So I thinks, it's better to change..?
Im a technician that just got back into the trade after 10yrs and had never done an electrolux boot replacement I tried for almost 2hrs to put the outer spring ont the boot but it kept slippin out at the end I just got frustrated and had my company send another tech to finish....anyone have any suggestions or tricks of the trade they wanna share? Sorry it wasn't a replacement boot I had to take it apart to replace drain hose....
We did our washer.. But the drum wouldn't spin when we were done.. Took the bellow/seal back out and the drum was free again.. I'm assuming that I wedged the bellow in too deeply, but it's how it seems to fit.. I'm at a loss...
The inner spring definitely does not go on anywhere near that easy. My inner spring had so much tension, I could stand on one side of the spring and pull up with both hands as hard as I can on the other side and still barely stretch it enough to go around the door. The installation pins were useless. I tried spring clamps, but there wasn’t enough room to hold the spring while heaving on it to stretch around the door. I know why our repair guy basically refused to change the boot steel when making a previous service call.
The boot seal I ordered was missing the rubber sleeve where the vent tube goes into. They must have cut it off. I tried to rig it up but I’m not 100% sure the tube will stay in there. This is so irritating.
Does anyone know if this can be done without taking the top and front panels off? My washer and dryer are stacked and was hoping to not have to unstack them and still replace the boot?
We got ours back on and double checked it’s all on correctly. However when we spin the inner tub it rubs on the bellow making a squeaking noise. Does it just need lubrication?
That shouldn't be necessary. We'd be happy to help you figure that out, but we'll need some additional information about the model and the problem. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need the model number for the appliance, so that we can look up diagrams and information about your specific unit to give you accurate advice. You can look here on our website to help you find the model number: www.appliancepartspros.com/modelnumber_locator.aspx
PS, if you use a solution of Borax and water it makes installing the bellows a lot easier PLUS Borax is "THE" compound you want to use to clean your washer. Run a few loads w/ Borax and see for your self .
@@staciecook5217 i ended up getting a new washer but have not had any problems. I leave the door open and wipe the bottom of the seals when I am done with laundry.
Can you tell me the best way to get access in a hotpoint Ultima wdd960 washer dryer to the broken counter weight concrete block at the front under the door, the front panel doesn't seem to have anyway to come off ?
We'd be happy to help you out with that! We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
My dryer is on top of my washing machine. It would be a big deal for me to tak the dryer down to remove the top of the washer to replace the boot seal. Can this be done without removing the top of the washing machine?
I’m having a problem with the seal staying on. The tab at the 11 o’clock won’t let the seal stay on. It keeps popping off . Anybody know what I’m doing wrong?
Where can you get tool to put the spring on. O know my husband and I can put the boot on, but we need the tool to stretch the spring. We don't want to pay $200 for profession to do it. Thank you!
Okay! Here's the link for the door boot seal on our website: www.appliancepartspros.com/frigidaire-bellows-kit-134515300-ap3869103.html If you check out the product photo, you'll see that it comes with two of the spring retainers.
We'll be happy to help figure out what's causing that. Since you installed two different parts, we'll need to ask you some questions to figure out where the problem is. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/.
If you need additional help with the repair outside of what's demonstrated in the video, you can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We also have a free repair forum where the techs can help you troubleshoot the problem: forum.appliancepartspros.com/. We’re here to help 7 days a week.
I picked up this Frigidaire Washing Machine Model# GLTF290ES0 for $75.. The boot is dirty and has a bad moldy odor. I don't think it's the washing machine itself. I think I may have to do this update to be rid of the odor! Anyone else experiencing this? Baking soda is not getting rid of the odor.
Are the SPRING RETAINERS - for 134515300 SOLD SEPERATELY? (Affinity Front Load Washer Model # FAFW3801LW3) MFG 05/12I contacted Sears and they said no. I just need to clean my boot not replace it. I knew this would be a challenge but wanted to know if I could lighten my load with at least getting the proper short cut tools...Thanks (Affinity Front Load Washer Model # FAFW3801LW3) MFG 05/12
Yep! We have the inner bellow spring clamp here: www.appliancepartspros.com/frigidaire-spring-134365300-ap3791178.html and the outer bellow clamp here: www.appliancepartspros.com/frigidaire-clamp-134527100-ap3844563.html. If you need any other parts for your appliance model, you can find them all listed here: www.appliancepartspros.com/parts-for-frigidaire-fafw3801lw3.html
Seems as the rubber seal is hitting the glass door and doesn't allow my door to shut... I installed the bellow as in video. It's all aligned. Not sure what the issue is. Can someone help?
I'm having this same problem - my door is rubbing the front of the boot as I try to close it, which also means nothing about the drum would be affecting this problem. I just replaced the latch, too and that didn't help. Would be great to have a solution to this problem.
CrapEagle It's on correctly.. just let it set in and it will adjust itself. My did after 2 months. Just press the door in and hold it while u press start for your machine to begin
Thanks for the quick reply TXguy82, I appreciate it. Hopefully I get the same result - I was going to be so mad if I needed to do more work to get this thing fixed before giving this repair as a Christmas gift!
it does not hold it in place when you are stretching that spring... you purposely cut to the end of the part where you were stretching the spring because you probably had problems yourself. The plastic retainers do not hold, and as a matter of fact, they even smacked me in the head as they shot off.
I actually had to hire repairman (with about 25 yrs experience) who explained to me that the four times he had to do this, he could not do to it himself, and needed a second person to hold the spacers. I actually had to help him.
Joel Silverman I've been working in the field for 2 years now and this is the hardest seal I ever installed, even harder than the first one 2 years ago in school! This is not an easy job as was portrayed in the video.
I really do hate to see the GOUGING, the cost for the "special" spring pliers is offthe hook exorbitant. I have a good mind to draw up a set in CAD and water jetcut several hundred pair for 1/2 the money or less WITH FREE SHIPPING. Sure, you can use 2 pair of needle nose w/ a fulcrum of the proper length in-between but that itself is a biotch. The folks selling the bellows should offer the tools at a greatly reduced price w/ each set, not the rip off price you would charge the Taliban for cryin' out loud. Some of these clowns want almost $200 for a set of these "special" pliers... NOT!
+ArtisannasitrA The special tools can be expensive but sometimes are needed. In most videos we try show you how to do it without them but in some cases they have to be used.
The spring was definitely the most difficult part and had to get my wife to help. I followed the video and got the job done in 4hrs but took quite a few breaks along the way. I made up my mind before beginning the project that I was going to be patient and that paid dividends. Don't start this unless you have ample time. Drink a couple while you do it but not too much. Saved big bucks!!!
Man, I have been on this for 5 hours now. Drank several, cussed, drank some more. Taking apart AGAIN because it was leaking after I had it all put back together. The spring is by far the hardest part to do. I think I've drank enough because I'm laughing I stead of cussing now...
I do 2 a week in an apartment building and for customers it take 15-20 mins max step 1 do not remove anything you need 2 large clamps the squeeze kind also lubricant the boot b4 you put it on the tub stretch the rear spring about 1-2 inches it will still hold as you put the spring around the rear boot use the large clamps to hold it in place starting at 12 o’clock fold it inside the tub so you can use the clamps
Any suggestions for no plastic plugs and doing it old fashioned with just hands ?????
Just did this as well. Thank you for the video. I agree the retainer spring was very hard and the two wedges provided not nearly adequate. Do what I did, go to the hardware store and buy a 3/4" x 48" wooden dowel for 2-3 bucks. Have them cut it up in 4" chunks and use those for wedges while going around. Double up on the wedges so friction is helping you out.
Glad the video was able to help you with the repair. And thanks for that tip!
Replacement complete. The patience required to reinstall the coil spring is understated, but the guide is invaluable.
Zachary Moseman Glad the video helped you get the seal changed!
The toughest part of the whole replacement is getting the rear coil spring back on. I read the comments below and knew it would be tough, then spent about 15 minutes trying by myself and getting frustrated. With an extra 2 helpers it only took about two minutes, HIGHLY recommend this approach. Started to put the spring on, put a AA battery at the 10 and 2 clock positions. My wife then held these two firmly in place so they wouldn't slip. I then stretched the spring out from both sides and my other helper used a small wooden dowel (almost anything will work) to work the spring into place from the 3 to 9 positions. Worked great and went fast.
That definitely is the toughest part of the repair. We're glad we were able to help you with it, though. Thanks for the tip about how you got it done!
Thanks, that really helped a lot!
Absolutely the perfect solution, they are the perfect size, I used about 8 of them and it only took 5 min to install...
Oh, also turn the boot inside out into the drum, gets it out of the way.
Cheers!
Struggled for an hour before I found this comment. Using AA batteries was the perfect solution! Thanks!!
The extra space at the counterweight mounting points was the perfect place to insert the battery then slide it to one side to lock the battery and spring in place. With the battery securely wedged, it allowed pulling spring tension As You Go much easier. Without pulling as you go, you won’t have enough left for the final effort. I only needed three batteries as I could pull the middle one and use it in the next space. Less than 15 minutes with this method.
Doing it this way is needlessly complex. You can replace the boot seal entirely through the front door of the washer. I did so myself having never done it before (I did take the front door off the washer to give more access to the boot seal, though). I'd heard this long, convoluted method wasn't necessary, and so gave the simpler method a try. It worked fine and no leaks after 3 weeks of use. (It was so easy to do, in fact, my wife volunteered me to do it again in a few years when the mold builds up again.)
Getting that spring on was one of the hardest things I've ever done.
Same i hate that they dont show how they did it
I said words I don't usually say!
Just took me over an hour to put that back spring on. Wanted to strangle the guy in the video for saying it was just a little difficult!
Seriously, put this on your resume.
Anyone do this without the “kit” that holds the spring in place? I’m going to try to use my temperamental wife, may cost me my marriage but here goes
As old as this video is, it's still relevant. Easy to follow step by step instructions. I completed this job today, which saved me $300 that I was quoted.
That was very challenging! The video was extremely helpful to see the steps, but I agree with one of the comments below that they quickly jumped to the end of the step with putting on the retainer spring because it is SO HARD!I do think this video makes it look deceptively easy. I finally got it after about 90 minutes and my fingers are raw. Here was my technique in the end... Get that first spring retainer thing wedged in there as well as you can. Keep checking on it and banging it in as it'll slip out. if you can get another person to check and hold it in, that might be helpful. Also, I think it helps to make sure that it's not sitting on ANY of the rubber, so it was pushing the rubber in toward the center and the spring a bit. I found other tools that I could wedge in there every few inches which helped in places, but one key is not to lay the spring slack from the first retainer to the next - stretch it as much as you can (even if you don't need to for that first bit) at the beginning and that'll make it easier in the end. I also found a pair of pliers which was the right size to wedge in sideways which helped to push the spring down and into the groove. Finally, I'd say work pretty quickly if possible. The slower you go the harder it is because you tire out and also the retainers slip, but until you get a good technique, I admit, it's really hard to work fast. I failed and cursed quite a few times before finally getting it... Good luck!!
Thanks for the tips! Glad you were able to get the washer fixed!
These tips are all great. The spring is hard, but doable with two sets of hands. Have someone hold down the retainer things for you, and then basically work as fast as you can.
Eric D ok no
Do some washers have different mechanisms to the spring lock , like a clamp with screw ?
I think my Miele might have this clamp screw lock for the inner spring , I’ll check on it.
I will not let this job defeat me!
Thank you for actually showing to use the clamps instead of those crappy place holders that come with the kit. The other videos on this cut away as the guy gets started on putting the interior spring ring and then cut to him all finished. Putting that first spring ring on is the HARDEST part of this, but you made it easy! Thanks!
Wow. Thank you so much for the video. I am a handy guy, but that inner spring is a huge pain! What worked for me was about six steel spring clamps with rubber padded tips that you can get at HD/Lowes for $1/each. I would get about 1/8th of the spring on, use a clamp, stretch on another 1/8th of the spring, another clamp, and repeat. It was still a pain and my thumbs are raw, but it can be done!
You're welcome! Thanks for that tip. Those springs can be tricky to get back on!
Awesome video - thank you. Replaced mine today, no issues. The hardest part was of course reinstalling the rear retaining spring. I first put those plastic retainers at 12 and 6 o’clock and secured them to the frame with nylon cable ties. Then stretched one side and fitted it into place, then the other. I am going to dry this one off after every wash - hopefully that will prevent the ugly mold. Thanks again!
The whole job took me about an hour to remove and replace my seal. I didn't need any clamps or the special tools as it all went pretty easily with brute force lol. Thanks for the help!
Great video! I knew the spring would be a beast so after 10 mins of battling, i took off the front counter weight and had plenty of room to easily install the spring. Saved a lot of time, frustration and patience with that. Thank you for the video!
Thank you very much. Even though these washers aren't worth fixing, you at least made it possible for those of us who are foolish enough to try. When it comes to installing the inner seal, drench and I mean drench it in lubricant, I ended up having to use WD40. Good luck to those who try.
Hey guys thanks for the video! Couldn't have done it without you. One tip I have for the large spring is to stretch it a little. I stood on it and pulled up. Maybe pull in small sections. I may have stretched it too much. One question/ issue I have after completing tho is my door didn't shut as well as it used too. Luckily it locks when running so it doesn't pop open. Thanks again!
I have the same door issue, did you ever resolve it not shutting?
@@SumanthBhaskaran no I didn't. When it's sensing it makes the buzzing noise. It's annoying but works ok.
@@michaelcassidy4095 Gotcha, thanks! Glad it will still work though
I have a tip for everybody for that innerspring because it's pretty difficult. You have to take the whole face of the washer off. Anyway I used two clamps, I started at the top( my washer had an indention on the boot behind the arrow that you snap into a tab at the top of the rim of the washer seat when I was mounting the boot) anyway , get your spring seated and put first clamp on very tight (at 12 o'clock) and work your way counterclockwise. After you get about 1/3 of the way or about 8 o'clock, put the second clamp on but it is very important while you are doing this TO KEEP TENSION ON THE SPRING (KEEP IT STRETCHED OUT AS MUCH AS POSSIBLE) Now with the clamp at 8 o'clock keep working your way to about 5 or 6 o'clock. Then move the 8 o'clock clamp to 6 oclock(left side of where you're pinching) then just keep workin it!!!, I did it by myself but two people would be easier. Make sure you keep tension on the spring until you get half way around( I think I kept tension on it longer so maybe just don't let up until your arm gives out) . Then you should have enough to muscle that cock sucker in there (excuse my French)lol. I used a flat head screw driver for the last 20 percent or so because the folded boot can get in the way. I hope this helps
Brendunt Scott You do not have the reply feature turned on. Clean everything as best you can, I am not sure baking soda will kill mold you might try bleach. You can also run some Affresh through it to help clean the inside. It is available on out website, part number: AP4308494.
I used some sockets that were just thick enough to stay in place. Harbor freight 7/16, 3/8 drive sockets did the trick lol. I used 2 of them. And found it easier to start at the top, then move the holders (sockets) down as I got more on, but you really have to pull and stretch the spring as you put it on, or you'll over extend the spring and ruin it. Once the spring is a little over half way on, I found the only way I could get it o was to pull it with both hands down, and over the bellow. Then sort of pull the bellow down hold it, while I used other hand to roll it into the channel until it finally snapped down in. Very tricky to install, but was able to figure it out.
HEY YOU! Yes YOU reading this comment. You were the man until you got to 6:05 huh? 😂
Really easy to put back inner spring if you take out the front panel and have set of at least 3 rubber big clamps (I got at HomeDepot for few dollars each). I used one of those auto mechanic clamps which forms a hole at the end when you close it and use that to drag the inner spring around gasket. Also make sure to use soap. Huge difference. Doing all this, it took me about 20 mins to do the versus trying for hours previously.
Just finished mine 10 mins ago and I can see how it can be a pain but mine went in like butter. So a few things defiantly use dishwasher soap I mean pour it on. Another thing I did was I had a heat gun and went around the areas that I was working with. When I first tried it without the soap and heat I couldn't get the thing to even start a seal. Once I lubed it up and just heated a section at a time and got it started it just slid in.So overall great video and since you just saved yourself about 50-100 bucks labor go do something fun tonight with that cash you just saved.
Thanks for the tips!
I should have read some comments! Nice tip. I'm going out tonight!
I removed the spring....put the wire in place and connected the end of the wire with a Zip Tie.... tightened it as much as I could and it works fine !
***** Just remember this is the main door seal, if the zip tie breaks you may have a good sized leak on the floor.
Diffidently a 2 person job. Somebody got to hold the spring retainers. Thanks for the video, it was a great help.
Corey Lambert Glad the video helped you get the washer fixed!
I just did it by myself and I'm a small dude. Lol. But I literally had to keep 20 lbs of muscle tension on the spring for the 15 minutes it took to put the inner spring on. My forearms were numb for a bit. 😂
So incredibly difficult. That tricky editing makes it look way to easy. Plan on at least 2 1/2 - 3 hours on this project.
Key thingsMore soap!
4 -6 Chapsticks wedged in sideways, the full length of the chapstick for 1st spring retailer. The plastic “tools” they provide are practically worthless.
Jumbo office binder clips for the second spring retainer. Attached binder clips as you work the spring around the boot to hold it in place. This made all the difference after many failed attempts.
Good luck!
This can be a lengthy process, and our editing process does cut out lengthy/repetitive scenes like unscrewing screws, so repairs generally do take longer than the length of our videos. Thank you for those tips.
Thank you very much. It was very hard to put the first part of the seal back but, at the end I was successful. Thank for the video.
The video was very helpful. The retainer spring was difficult. I had my wife help me, with an extra set of hands. Could not have done it on my own. Once again, thanks, you saved us a lot of money. :)
Glad the video helped you out!
First, I did not remove the top or front pieces as described in this video, as others have said it wasn't necessary to do the job. Would it have been easier to do? Not sure. I did this gasket/door boot replacement on my 2005 Kenmore front loader last week. The toughest part by far is getting that inner spring to go around gasket without popping off, even with the supplied retainers. I had to get my daughters help and we finally managed to get the spring on. It's definitely a struggle, but I was determined not to pay a service tech to do it. :-). The rest of the job is easy.
One other note; there was a lot of crud (for lack of better words) around the washer drum and the plastic rim that the inner boot goes onto. I took some time to get as much of it out/cleaned as possible. You might want to check yours and do the same. I'm in Canada and paid $282 with tax for this part. Was pretty shocked at the cost considering it's basically just molded rubber. I think my next washer will be a top loader again. Then you don't have to worry about the rubber boot needing to replaced.
282 is absolutely ridiculous, even if I purchase this in the US, I'll be out over 100$ which I'm still rolling my eyes about. i expected about 60$ or this part. I'm ordering my part today, thanks for the Tip.
Yeah, couldn't believe the cost. Might have been able to get it a bit cheaper, but was in a rush to get the job done so got it from a local store here within a day. Also, make good and sure you're getting the right part. They new part is an improvement over the old for sure. Good luck with getting yours replaced.
Just did it myself with the help of a friend. Until I removed the front and top panel, I couldn't even get the inner spring out! Removing the front panel allows for much more space to work with. Would recommend. Also, the it's almost impossible to get the inner spring on with only two hands. retainer thing keeps popping off. You need at least four hands stretching the spring four ways. Last bits, use a flat-head screw driver to ply it in.
I found the same thing...you need an extra pair of hands to keep that inner spring from popping out. What make of washer do you have? The one in the video here is a Fridgidaire....mine was a Kenmore and is slightly different in design.
Yikes. Just paid $113 usd on Amazon for this. Also got a new outer ring for $24 as mine was rusty. I really wish that one little plastic tye for the top hose was included. It costs pennies but now I have to take a trip to the hardware store 😒. Wish my luck, guys.
I found this video helpful. Took me about 20 min total to change the seal. Putting the inner spring on is the hardest part. I found the retainers worked well. Bye bye old nasty seal ;)
spencer Underhill Awesome, glad the video helped you get the seal changed!
Thank you for the video - for those shore doing this alone - go and get yourself 5-4 padded clamps at Home Depot 99 cents each - you ll be done in 5 mins
A note, the earlier model of these washer do not allow enough room for the spring retainers, watch for them flying out at your face while you stretch the spring.
Thank you for the tip!
These Simple instructions worked perfect, Thanks for posting, got it up and running in no time.
Glad the video helped you get the door boot on!
parts for a mini Lady kenmore dryer
The spring retainers provided are not adequate and I’m not sure how it was possible you were able to install it without additional items. The amount of tension on the spring is enormous. A more realistic installation of that spring requires two or more clamps and a long shaft flathead screwdriver to leverage the spring around the boot.
My Frigidaire has an additional piece below the door that needs to come off before I can access those bottom screws. Any tips?
We replaced the bellow, without removing the top, nor front panels, but the spring is way harder than the ones on the whirlpool washers
If the sprig retainers don't fit between the weight and the tub what can I use to hold it in place. This is infuriatingly difficult.
Frigidaire gallery 10 years old.
Took me a bit with the rings but I got it done! No leaks!
Really very Thanksm y friend, very helpful.
Only one question..,
All the machines, works in the same way..?
My wife's machine is a Samsung, and the ruber is become dirty and black,
So I thinks, it's better to change..?
They are all similar but they do use different clamps on some brands.
Im a technician that just got back into the trade after 10yrs and had never done an electrolux boot replacement I tried for almost 2hrs to put the outer spring ont the boot but it kept slippin out at the end I just got frustrated and had my company send another tech to finish....anyone have any suggestions or tricks of the trade they wanna share? Sorry it wasn't a replacement boot I had to take it apart to replace drain hose....
Can I order the spring retainers separate without ordering the bellow.
This video is great ! So are all the comments and tips. Has any body tried this without removing any panel?
Glad the video helped you out!
You guys are the best. Keep it up ! I have been a customer for years.
Thanks for the orders, glad the videos are helping you out!
We did our washer.. But the drum wouldn't spin when we were done.. Took the bellow/seal back out and the drum was free again.. I'm assuming that I wedged the bellow in too deeply, but it's how it seems to fit.. I'm at a loss...
The inner spring definitely does not go on anywhere near that easy. My inner spring had so much tension, I could stand on one side of the spring and pull up with both hands as hard as I can on the other side and still barely stretch it enough to go around the door. The installation pins were useless. I tried spring clamps, but there wasn’t enough room to hold the spring while heaving on it to stretch around the door. I know why our repair guy basically refused to change the boot steel when making a previous service call.
The boot seal I ordered was missing the rubber sleeve where the vent tube goes into. They must have cut it off. I tried to rig it up but I’m not 100% sure the tube will stay in there. This is so irritating.
Does anyone know if this can be done without taking the top and front panels off? My washer and dryer are stacked and was hoping to not have to unstack them and still replace the boot?
This video was more helpful than others.
Appliancepartspros; could you use Jet-Dry for the lubricant?
We got ours back on and double checked it’s all on correctly. However when we spin the inner tub it rubs on the bellow making a squeaking noise. Does it just need lubrication?
That shouldn't be necessary. We'd be happy to help you figure that out, but we'll need some additional information about the model and the problem. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need the model number for the appliance, so that we can look up diagrams and information about your specific unit to give you accurate advice. You can look here on our website to help you find the model number: www.appliancepartspros.com/modelnumber_locator.aspx
Where can I find those Spring retainers
Fantastic thank you for your technical knowledge
PS, if you use a solution of Borax and water it makes installing the bellows a lot easier PLUS Borax is "THE" compound you want to use to clean your washer. Run a few loads w/ Borax and see for your self .
+ArtisannasitrA Thanks for the tip!
What do you do if after replacing the seal before putting the top on (8:21) the door will not stay closed.
I have the same door issue, did you ever resolve it not closing?
Just repaired mine thanks.
Mold sent me here.
Johnny N. Did u replace or try to take off the mold ?
Same here.
Leaky complaining washing machine wouldn’t shut up when doing its job.
Same
@@staciecook5217 i ended up getting a new washer but have not had any problems. I leave the door open and wipe the bottom of the seals when I am done with laundry.
Can you tell me the best way to get access in a hotpoint Ultima wdd960 washer dryer to the broken counter weight concrete block at the front under the door, the front panel doesn't seem to have anyway to come off ?
We'd be happy to help you out with that! We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
My dryer is on top of my washing machine. It would be a big deal for me to tak the dryer down to remove the top of the washer to replace the boot seal. Can this be done without removing the top of the washing machine?
No, you will need to remove the top of the machine. You won't be able to get to the screws to remove the front without first taking off the top.
wow man was tuff but the video helped alot
Took 3 hours two hours on the rubber boot spring was easy
I’m having a problem with the seal staying on. The tab at the 11 o’clock won’t let the seal stay on. It keeps popping off . Anybody know what I’m doing wrong?
@6:10 from then on you have to have some strength to go around with that boot spring!
Go buy a big pack of AA batteries. They’re the perfect size to hold that spring. Got it in under 20 minutes.
Glad to hear you were able to fix your appliance!
Where can you get tool to put the spring on. O know my husband and I can put the boot on, but we need the tool to stretch the spring. We don't want to pay $200 for profession to do it. Thank you!
Do you mean the spring retainer tools shown at 5:35? If you bought the kit from us, it should have come with them.
Yes !
Okay! Here's the link for the door boot seal on our website: www.appliancepartspros.com/frigidaire-bellows-kit-134515300-ap3869103.html If you check out the product photo, you'll see that it comes with two of the spring retainers.
replaced boot. 1st run was ok. 2nd one has a rub and now when I spin drum it is touching. Normal?
We'll be happy to help figure out what's causing that. Since you installed two different parts, we'll need to ask you some questions to figure out where the problem is. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/.
great video 👍
Glad you enjoyed the video!
The seal draining scape doesn't have a hole is it supposed to be like that?
If you need additional help with the repair outside of what's demonstrated in the video, you can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We also have a free repair forum where the techs can help you troubleshoot the problem: forum.appliancepartspros.com/. We’re here to help 7 days a week.
So 6 minutes in you must of edited out how difficult the string is
teşekkürler . Güzel bir paylaşım olmuş, sayenizde çamaşır makinesini tamir ettim :)
Tamir etmene yardımcı olabileceğimize sevindim.
Thank you!
Cómo desmontar un centro de lavado marca Frigidaire
I picked up this Frigidaire Washing Machine Model# GLTF290ES0 for $75.. The boot is dirty and has a bad moldy odor. I don't think it's the washing machine itself. I think I may have to do this update to be rid of the odor! Anyone else experiencing this? Baking soda is not getting rid of the odor.
Great video! Thanks
Are the SPRING RETAINERS - for 134515300 SOLD SEPERATELY? (Affinity Front Load Washer Model # FAFW3801LW3) MFG 05/12I contacted Sears and they said no. I just need to clean my boot not replace it. I knew this would be a challenge but wanted to know if I could lighten my load with at least getting the proper short cut tools...Thanks (Affinity Front Load Washer Model # FAFW3801LW3) MFG 05/12
Yep! We have the inner bellow spring clamp here: www.appliancepartspros.com/frigidaire-spring-134365300-ap3791178.html and the outer bellow clamp here: www.appliancepartspros.com/frigidaire-clamp-134527100-ap3844563.html. If you need any other parts for your appliance model, you can find them all listed here: www.appliancepartspros.com/parts-for-frigidaire-fafw3801lw3.html
Seems as the rubber seal is hitting the glass door and doesn't allow my door to shut... I installed the bellow as in video. It's all aligned. Not sure what the issue is. Can someone help?
I would make sure the seal is installed properly. Also make sure the inner drum is not moving, could be a bad spider or bearings.
It's on correctly... Not sure why it doesn't close easily but I'm able to wash still. No biggie I guess
I'm having this same problem - my door is rubbing the front of the boot as I try to close it, which also means nothing about the drum would be affecting this problem. I just replaced the latch, too and that didn't help. Would be great to have a solution to this problem.
CrapEagle It's on correctly.. just let it set in and it will adjust itself. My did after 2 months. Just press the door in and hold it while u press start for your machine to begin
Thanks for the quick reply TXguy82, I appreciate it. Hopefully I get the same result - I was going to be so mad if I needed to do more work to get this thing fixed before giving this repair as a Christmas gift!
It’s not necessary to take the thing apart like that.
Silicone worked great as I lube.
muito bom
Exelente!!!
¡Estamos felices de servir!
Thanks !
You're welcome!
it does not hold it in place when you are stretching that spring... you purposely cut to the end of the part where you were stretching the spring because you probably had problems yourself. The plastic retainers do not hold, and as a matter of fact, they even smacked me in the head as they shot off.
Joel Silverman The spacers are tricky, I have had some that stayed and some that did not. Hope the video helped get the washer repaired!
I actually had to hire repairman (with about 25 yrs experience) who explained to me that the four times he had to do this, he could not do to it himself, and needed a second person to hold the spacers. I actually had to help him.
Joel Silverman Glad you were able to get the washer fixed!
Joel Silverman I've been working in the field for 2 years now and this is the hardest seal I ever installed, even harder than the first one 2 years ago in school! This is not an easy job as was portrayed in the video.
It’s a good thing you cut out all the yelling and swearing While pulling that’s spring around the boot.
😂
Why can't my retainer spring be that easy!!!!
Sorry you're having a difficult time with it! If you have any questions, we'll be happy to help.
i love it xxxx
+Nicholas Mahoney Glad the video helped you get the washer fixed!
now my children love it too (madi mahoney)
+Nicholas Mahoney Thanks!
thanx
+dina perl Glad the video helped you get the washer fixed!
I really do hate to see the GOUGING, the cost for the "special" spring pliers is offthe hook exorbitant. I have a good mind to draw up a set in CAD and water jetcut several hundred pair for 1/2 the money or less WITH FREE SHIPPING. Sure, you can use 2 pair of needle nose w/ a fulcrum of the proper length in-between but that itself is a biotch. The folks selling the bellows should offer the tools at a greatly reduced price w/ each set, not the rip off price you would charge the Taliban for cryin' out loud. Some of these clowns want almost $200 for a set of these "special" pliers... NOT!
+ArtisannasitrA The special tools can be expensive but sometimes are needed. In most videos we try show you how to do it without them but in some cases they have to be used.
ayuda de estos videos en español
Fabian Reinoso At this time we have not translated these videos to other languages. I hope the video helps you get the repair done!
Take that counter weight off to save you hours of frustration
😢
This guy's for crap about the back spring. It takes a good 10 plus tries to get it on. Took me an hour. That part will be very difficult
ok thng
Glad the video helped!
A few minutes of your time. LMFAO
Seriously a pair of gloves to do that kind of work .LOL
Removing the top and front panel is unecessary.
Guwno 🚽🚽🚽🚽🚽🚽🚽😭😭😭😭😭😭
Terrible