I made one in about 30 minutes for just under 40$ for everything. Works great with tons of smoke. If you make one turn it on outside. They smell funky.
motoYam82 now if only there were a check valve to prevent the fuel vapor from re-entering the canister where the possibility of spark is . I would hate to see someone lose their house , life , or hair
motoYam82 After I finish my testing with smoke machine I would disconnect it from power and leave my air supply for next 2-3 minutest to push all of possible vapor out of my smoke machine.
thank you, I think I will make one, I suspect a vacuum leak in my 3800 Buick park avenue! I suspect it to be the intake manifold gasket. so once again I thank you so very much!
Nice design.Did you ever think of using a 4in threaded clean out on one end so you could replace your heating coil or your wick? I plan on making one that way. I like yours better than a tin can
Very nice. Personally, I got a friend who has one of those vapes, the kind that pumps out a haunted house’s worth of fog. Whenever I suspect a leak, I call him over and have him exhale into the tube
Hello, I want to make one of these. now I was wondering. I bought a pressure transformer, really don't know a better word for it, but it's output is only 50 mm bar which is 0.73 psi. would you consider that enough pressure or really to low? thanks, Martijn
What I would do to be able to take this apart is to not glue it together, but to push the caps on the pipe, drill a couple of holes into each cap and screw them together. If you’re familiar with pvc, just pushing two pieces together is hard to pull apart.
I made one in about 30 minutes for just under 40$ for everything. Works great with tons of smoke. If you make one turn it on outside. They smell funky.
Fantastic, looks much more streamlined than a paint can design!
motoYam82 this smoke machine works great I use it almost every week, please watch my video with first look sensor I am sure you will like it.
motoYam82 now if only there were a check valve to prevent the fuel vapor from re-entering the canister where the possibility of spark is . I would hate to see someone lose their house , life , or hair
motoYam82 After I finish my testing with smoke machine I would disconnect it from power and leave my air supply for next 2-3 minutest to push all of possible vapor out of my smoke machine.
New Level Auto - highly unlikely dude, more likely you get run over by car first!
Wonderful DIY, thanks.
thank you, I think I will make one, I suspect a vacuum leak in my 3800 Buick park avenue! I suspect it to be the intake manifold gasket. so once again I thank you so very much!
Good job Man , your explanation on everything was well taken , I have plenty of that hair dryer wire on hand to make my smoker.
This is my favorite tool. Works great. Cheers
Good idea
innovative nice good job
Tris A Thank you. This smoke machine works great. Cheers
Good! First one to show a pressure regulator and how low the pressure has to. BE to test
Nice design.Did you ever think of using a 4in threaded clean out on one end so you could replace your heating coil or your wick? I plan on making one that way. I like yours better than a tin can
Very nice. Personally, I got a friend who has one of those vapes, the kind that pumps out a haunted house’s worth of fog. Whenever I suspect a leak, I call him over and have him exhale into the tube
Where did you go up? I hear accents well and im having trouble placing yours.
Do we need to close the throttle body?
Hello, I want to make one of these. now I was wondering. I bought a pressure transformer, really don't know a better word for it, but it's output is only 50 mm bar which is 0.73 psi. would you consider that enough pressure or really to low? thanks, Martijn
majetoJESUS yes that will work you don't want to pressurize system over 1 psi.
Happy
I like this machine.
Can i use any wire for the resistance?
ron labbe No you need to use heating element from hair drier. Thank you
KY Home Garage KY Home Garage
Thank you!!!!
That Chrysler IS the smoke MASHAIN! 🤣 Just kidding.
😂😂😂
How did you seal the hole where the power leads go through the PVC pipe?
I used rubber grommet.
What I would do to be able to take this apart is to not glue it together, but to push the caps on the pipe, drill a couple of holes into each cap and screw them together. If you’re familiar with pvc, just pushing two pieces together is hard to pull apart.
How to make the ball that drops
Go to new york on new years eve
Sorry, but a heating element in a flammable plastic container is a bad idea.
UtwoBed OK thank you for watching.
its pcv will not burn12volt element heats oil on wick only
UtwoBed - wrong, not flammable but only combustible!
@@smokenbudesq PVC
www.homedepot.ca/en/home/categories/building-materials/plumbing/pipe-and-fittings/pvc-pipes-and-fittings.html