Troubleshoot/Repair a Motorcycle Turn Signal Light

Troubleshoot turn light. Check continuity of bulb filaments with a multimeter. Using the Ohms meter. Cleaned contacts . Reassemble light. Turn light operationally checks good.
Visit eaglerunnerbill...

[@monkeymedia1257]

even after 40 years people would still thank you.

[@WillyDaC]

Good video. I just did a swap from relocated turn signals on my 2012 Super Glide. All brand new factory stock OEM turn signals. Tested them before I went to replace the standard lenses to the amber bulb/smoked lens's. The front signals did not work. I noticed that there was so much dielectric grease in the new sockets that there was no way anything could make a decent connection. Look up the definition of dielectric. It does not conduct. Your video could save a lot of folks headaches and tearing apart things that don't need to be. The simple solution works is most often the best solution. Again, good video.

[@kelhawk1]

A practical, well put together dialogue, and your down to Earth delivery style, made for a great video!

[@run2thefight]

Hey man thanks for the advice I actually had a broken contact and replaced my entire light assembly but now the same side that wasn’t working before still isn’t working I am at a loss as to why it won’t even light up as a running late or turn signal

[@dave32228]

can you use wd 40 to clean the contacts

[@soranys]

Hi, thanks for your explanation video. I have a problem with my marauder 1997 which start with back right signal not working and the front right signal blinks quicker than normal, then start not blinking at all, then all signals went off and not working even the green light for the neutral. now only the normal and high light with the back and break light is working normally, and the motor start too! what do I need to check ??? where can I start!

[@redentorcuyugan6138]

Awesome video! Thanks for sharing!

[@VashStarwind]

I just wanted to say, if you arent sure if your bulb is working or not, swap it with another blinkers bulb, and that should tell you if its the bulb or the contacts. Figured that might help someone.

[@genjiegeneralgaming3582]

We're all of ur blinkers not working I'm having that issue on my enduro

[@JulianJohanson]

Only one side quit on my Wr but it blinks my twilight and everything electrical when I press to the right left is normal

[@user-ze7vi9kw2v]

Does the front lights stay on? Mine does

[@heading7593]

is that jonny cash talking about motorcycles?

[@billeaglerunner6844]

Thx for watching.

[@megapet777]

out of nowhere my rear left blinker and headlight stopped working. Any idea what would cause it? My high beam and low beam doesn't work at all but when I hold "pass" button the light works.

[@stevenmayo9636]

It’s the back ones that are tough to get to

[@hequsn]

On my atv the blinkers work when the engine is not running but only blink once and then turn Off when the engine is running. Any ideas to solve this?

[@mimodelorean]

cheers m8! thanks for yer time

[@billeaglerunner6844]

Thx for watching.

[@bryantacazon6786]

i try your method but my issue is the bulb housing on my bike. i buy the pair mirror turn signal. but in other bikes it works

[@leonscott4re]

My back left light not blinking

[@bryantacazon6786]

thanks for the video i got this problem i hope that helps me

[@billeaglerunner6844]

+Bryan Tacazon Thanks for watching.

[@stephsimartinez164]

What if the turn signal stays on all the time on my right side

[@domonkosmihalyi9104]

Hi! I have the same problem, and I was wondering, if you managed to solve it? If so, could you help me out?

[@cj8172]

@@domonkosmihalyi9104 I have a similar issue, it blinks ok until I rev the engine and then it just stays on without blinking. Kinda strange

[@cyberjack]

my bike only flashers if i rev engine ? .

[@1975dcolvin]

I am having the same problem with a 1982 yahama maxim xj750

[@garytauber430]

I got same problem my bike is 1983

[@davidquintana8395]

put lithium grease inside bulb receptacle and bulb stem

[@buckrogers2546]

sumshin