YOU HAVE LITERALLY JUST SAVED ME SO MUCH TIME! I HAVE BEEN HAVING ISSUES WITH THE NEW LASER MASTER 3 FOR THE LAST 4 HOURS!!!!!!! I have even taken the entire machine apart to check all connections are in place as the device would not move or go home. BUT BY USING THE $RST=* code that you mentioned, it reset the entire device and it is now working again. I cannot thank you enough! You really have made my entire year!
As usual when I need a great tutorial you have it Jim ! Thanks and I can't believe how the channel has grown since you first started less than 2 years ago or so !! Best to you and the family.
Good video while it might be 2 yrs old now and for the OLM2 rather then my OLM3 it still was the ONLY video that clearly shows how to check current firmware in my laser. Thank you
@@TheEdgeofTech Might be worth adding a sticky note that the power/reset buttons layout that determines motherboard type (1.3 vs Pro) doesn't mean that you have a Laser Master 2 Pro. Looks like a few of us have downloaded the LM2 Pro firmware update, causing issues. Most notably homing to the bottom right, because apparently the LM2 Pro has the X-motor inverted.
Have to chuckle at the recommendations ... When NOT to up upgrade or reinstall firmware: - Ortur Laser Master 2 is working correctly and showing no problems When TO upgrade the firmware: - A new version of the firmware is posted... I'm not having issues, but a new version is posted .... WHAT TO DO ??? hehe ; ) Thanks for the video.
I did it! It only took me 3 hours!!! ( had lunch, and some of the instructions didn't work first time, I better go back and see if I still have virus check off! )
Just an FYI on the Laser Master 2 Pro S2 I upgraded from 1.85 to 1.87 after you copy the bin file it auto closes laser drive & powers down laser. I confirmed it did upgrade in Lightburn.
I have the latest lightburn 0.9.20 but when I right clicked on the “devices” tab but it’s resetting the current device connection. I’m not getting the pop up that you are getting
@@ryanbeharry5636 Near the move tab is a console tab. When you start up the laser it will automatically home and the message will show up in there. Good luck
I havent followed this advice as yet, and now I am reluctant to change anything after reading all this. This is the message I got whilst trying out my LM2 20w (older version). Starting stream Layer C01 Pass 1 of 2 Layer C01 Pass 2 of 2 Layer C01 Layer C01 Layer C01 Layer C01 Layer C01 Layer C01 Layer C01 Layer C01 Detect movement, terminate laser engraving! Acceleration fluctuation:325 Reset Grbl. Ortur Laser Master 2 Ready! OLF 137. Grbl 1.1f ['$' for help] [MSG:'$H'|'$X' to unlock] error:9 G-code locked out during alarm or jog state. On or near line 39911: Job halted Stream completed in 50:51
My "devices" doesn't do anything if I right-click on it. a left click just brings up the name of the laser it found. I'm wondering how to check the current version of firmware I have?
bonjour j'ai update le firmware de mon ortur laser master2 tous c'est passe correctement mais j'ai un souci le homing avant quand je debranchait l'axe y pour y brancher le rouleau en ayant pris soin de mettre le homming a 0 au lieu de 1 je n'avais pas de probleme mais depuis si je fait cette procedure mon laser se met en alarm sur grbl sauf sur lightburn: pourquoi cdlt serait ce du que j'ai mis le 142
Did the upgrade. and then would not start. I did not have clue as what happened. So after searching for about 6 hours I found the OEM bin file. put it back and back up and running Tech support. all they could say is try this try that. if there is anyone who had the same problem let me know what you did to get it back up and running. Cheers
Jim, in the caution note you say not to use the PRO firmware and use the LM or LM2 firmware. I assume that is because you have the LM or LM2 model. I have the LM2Pro so I should be using that version? I'm new to all of this laser stuff so I'm trying to muddle through it all. Thanks in advance.
Ok did all that but now my laser is not burning at full power, seems to only be burning at about 25% power. I am using lasergrbl when I click the laser button so I can set the focus the laser shuts off after a few seconds and then I have to reset the Ortur. Anyone have any idea whats going on here. Used my burner a few weeks ago with no issue to burn some Harry Potter coasters. Any help would be greatly appreciated. Thanks
I would try it again and make sure you have the correct firmware for your laser. Otherwise jump on the Facebook group and tag Gil. He is support and he will help you get it worked out!
Hi, I need some help, i have just purchased laser master 2s2, and set it up, the only trouble is the X-axis is not moving, I have checked the cables and when i home the y-axis moves but the x-axis does not, plus the laser GRBL shows an icon that says 'Alarm' can you help?
Hello. I have a question for you. Did you ever test if you can put this machine on the wall and use it like that? to cut some plywood on the wall? Would be really nice if you would be willing to test this. Thank you, and keep up the good job with your videos. I wanted to buy this machine, that why I asked... I am bad with space...
I have old 170 on mine, but I tried this method and it won't stay connected to the PC in my computer. So I cannot update to the latest firmware. I believe the prior owner must have installed the wrong firmware on my machine. It works, but it's not right
Unfortunately, when I try to copy the BIN file over the D drive closes and it gives me an error saying it can't do that. I have a error on lightburn saying "Emergecy Switch Engaged" and the thing just won't do anything. I just put it together, too. So frustrating. I'm waiting to hear back from support. But if anyone knows how to fix this, I would be grateful.
Hey there...I have watched several other videos you have that have been very helpful and have recently subscribed. I tried the firmware update this morning and after dragging the new .bin file over pressing the reset and then the power button get nothing. Was hoping this update fixed a couple disconnect issues in the middle of a few burns but this not powering up thing has me freaked out! I did message Gil and Ortur tech support and am trying to be patient for a reply from either. Is this fixable as far as you know with out having to order new parts???
I have a Ortur LM2. I'm having trouble with the drive it creates when I hit the reset button after holding the power. As soon as I try to copy the bin file, the drive disconnects and the file does not copy. Any thoughts? Thank you
Hello, I just put together the machine, but It shows issues with Expressif CDC device not installed, and I cant find any info on Google. Would someone know the solution? cheers
Any idea if the firmware updates are all inclusive of previous ones or do you need to do each one in order. Mine is 1.37 and see there are two other updates. Thanks.
So, I followed all the steps exactly as in your video. After I copy and pasted the bin file and hit the reset button the laser turned off, but now I can't get it to power back on. Not sure what to do now. Please let me know if you have any suggestions. Thank you. Your videos are awesome.
When downloading the newest firmware from the depository I never get version 1.90. It keeps giving version 1.85. So what is the latest version 1.85 or 1.90? This is a brand new Ortur laser master 2 pro s2
So just went through this whole process and now the unit wont power back on. Everything went exactly as you showed, but after the reset, the power button wont work. Any ideas?
please help not find help anywhere i have new version for a while now and keep getting (error:9 G-code locked out during alarm or jog state.) I Have check everything cords power source and reset everything still doing it
Thanks for the helpful video. My LM2 Motherbaord replacement came with a power, USB and what looks like an ethernet conector on the front. Is this a Pro Baord?
Love your videos. I have one problem with this one. first let me say, I just received my Laser so tried The right click devices in to see if already has the new firmware. when doing so the laser Homes but no dialog box appears. What Is wrong or what am I doing wrong? using LB V0.9.24. Any help is greatly appreciated!
Well, just got my laser...put it together, excited to try it...noticed the firmware was not the current one...apparently against my better judgement, followed all the instructions to update and now I'm stuck with it not turning on. Still can get it to mount to the computer but nothing else. I've reached out on the Facebook group so hopefully I can get it sorted but man I'm bummed out.
@@Mysticalmantiscreations yes extracted it with WinRAR...which includes the bin file, pdf instructions, and changelog. Pretty sure I can't extract it any further, atleast not with right clicking it.
Sorry man, other than that the only thing I ran into was I didnt have the Pro (which I thought i had) i downloaded the other one that wasnt for the pro and extracted and it worked fine.
@@Mysticalmantiscreations so I thought about that but apparently everybody is supposed to download the standard file because the Pro download is for a different machine not out yet...not for the Pro motherboard
I did the update just fine, cleared everything but now my homing is completely jacked. It is trying to home to the lower right even though everything in the setup is lower left. It can’t find my project on the table and the fan stays on after I try to do a test fire or frame!!!! I have the latest LightBurn and Windows 10. Any ideas?
I did the firmware update and my laser will not turn on. I can open the folder as described in your video and drop the firmware in again but the same thing happens again. Have you any idea what I might need to do?
@@TheEdgeofTech Gil was fantastic, connected via software from his company and repaired ortur in less than 5 minutes. Thanks again for the recommendation. Keep up the good work Jim
Hi, great video.. but I tried the update and somehow I messed up now mi laser isn't responding theorize isn't popping up on my computer, Is there a way to factory reset my laser.
hello ortur Master..i have 2 problems with my ortur l M2..i havent had any problem a year ago..but now the machine working,laser is on,but doesnt burn nothing,with any different settings..and after i have tried to get a firmware,and i followed the process,but the bin file doesnt work,the machine doesnt want to start again?could you help me,how can i fix the problems,i think first the firmware,after the laser...i am working with windows 8...thanks to alll,have a good day 🙂
my olm2 wont power on im in the process of working on this and that with ortur support. May I know what is the name of the facebook group to find Gil to help me.
I believe my problem is that I applied the Pro firmware because of the video pointing out that I had the Pro button layout. But apparently that only means I have the Pro-style motherboard, and not the Pro LM2.
Well I have a good idea why they say dont use a Mac... Linux would have similar things... I bet it works fine if you make sure to unmount the drive after copying the file over.
It seems weird that there would be any problems when the Ortur simply sets up as a USB drive. I could see problems if there was update software needing to be run on Windows to transfer the firmware via a USB serial port connection but this method seems to be better and avoid those issues.
@@ElmerFuddGun yeah typically if you were to not allow the system to fully write to the attached disk before ejecting it may not actually write all the data. Ejecting forced that write to happen. Even in windows you could end up in a state where it did not fully write but that usually happens with very large files. If you have ever copied files on a mac or linux machine it can sometimes take a minute before it will tell you that the drive can be removed.
@@ottersdangerden - True. I don't have any Mac experience but do have Windows and Linux machines. There is a setting (at least in Windows) that can turn that "buffering" on and off on different drives. I always use the "eject" function out of habit and don't see how there would be a problem here. But like I said I don't have a Mac and Apple does do some weird stuff. ;-)
@@ElmerFuddGun turns out it has something to do with the hidden macos folder that gets dropped onto it, so that can cause it to fail. Linux can drop a fille there but that is pretty rare and if you know that is an issue its pretty easy to mitigate. (Liam at astroprint had Ortur support guy and thats where i got this info)
Are you sure you have the Pro? I thought I did, because of the way the buttons setup, but apparently that means it's a Pro motherboard, not the LM2 Pro. Caused me problems until I loaded the correct firmware.
DANGER i decided to follow your video and the result was that my ortur is now DEAD ! after your video like a idiot i decided to read the manual where it said something you didn't say......" DO NOT USE A USB HUB" connect directly to the PC. Duh .... anyone any ideas how to fix this now ?? its doing absolutely noting any more....😖
Press the reset button then the power button then the reset button again. And then try to turn it back on. Then go through the upgrade instructions without the hub if it turns back on. If it does not turn back on, jump in the ortour group on Facebook and ask Gil for help. He is the support and he will help very quickly.
ok update... disconnected the LM2 from the net and USB ... then reconnected the LM2 to a laptop with a very short usb cable. Then held the Reset button and second later the start button hold both till the light comes on (hopefully, took me 2 runs) then start the whole procedure again....this time with no hub or usb cable extender !!!! PROBLEM SOLVED
If your OLM2 works now WITHOUT any problems... My advice (like with all computer related hardware) DON'T update. That is my experience of 27 years working with computer hardware
After this de laser keep on 100% burning to his home position you now someting ? [MODEL: Ortur Laser Master 2] [OLF: 140] [DATE:17:23:54 - Jan 4 2021] [VER:1.1h.20190903:] [OPT:VNZHI,99,254] Target buffer size found ok Naar standaardinstelling ok Stream wordt gestart [MSG:Pgm End] Stream voltooid in 0:00 Stream wordt gestart Stream voltooid in 0:00 ok Stream wordt gestart Layer C00 [MSG:Pgm End] Stream voltooid in 0:03 After this de laser keep on burning to his home position
This is a really in-depth video, thanks for posting this walkthrough! Hopefully I can actually use it after I pick up an Ortur!
YOU HAVE LITERALLY JUST SAVED ME SO MUCH TIME! I HAVE BEEN HAVING ISSUES WITH THE NEW LASER MASTER 3 FOR THE LAST 4 HOURS!!!!!!! I have even taken the entire machine apart to check all connections are in place as the device would not move or go home. BUT BY USING THE $RST=* code that you mentioned, it reset the entire device and it is now working again. I cannot thank you enough! You really have made my entire year!
As usual when I need a great tutorial you have it Jim ! Thanks and I can't believe how the channel has grown since you first started less than 2 years ago or so !! Best to you and the family.
Worth the sub, I already have the update but it was a pleasure to listen to while working. All tutorials are well spoken and edited cleanly.
Good video while it might be 2 yrs old now and for the OLM2 rather then my OLM3 it still was the ONLY video that clearly shows how to check current firmware in my laser. Thank you
THANKS BUD, I WATCH, I UPDATED, I LIKED YOUR VIDEO. Thank you sir for doing this for the community.
Thank you, having someone walk you through it makes it so easy.
Thanks for explaining all of this! Sure appreciate your work man!
My pleasure! Thanks for watching!
@@TheEdgeofTech Might be worth adding a sticky note that the power/reset buttons layout that determines motherboard type (1.3 vs Pro) doesn't mean that you have a Laser Master 2 Pro. Looks like a few of us have downloaded the LM2 Pro firmware update, causing issues. Most notably homing to the bottom right, because apparently the LM2 Pro has the X-motor inverted.
@@Dadtheimpaler Thank you for the update! I was just going by their directions but this definitely helps!
thank you for all you do Jim, I followed step by step and boom its done. keep up the good work
Have to chuckle at the recommendations ...
When NOT to up upgrade or reinstall firmware:
- Ortur Laser Master 2 is working correctly and showing no problems
When TO upgrade the firmware:
- A new version of the firmware is posted...
I'm not having issues, but a new version is posted .... WHAT TO DO ??? hehe ; )
Thanks for the video.
Updated hardware and having issues with the burning what should I do I'm doing the same thing same settings still having problems
Bro. You explain everything so easy. Thanks
Thanks for the info. Sounds like they need to fix the issue of losing all the custom settings when updating firmware.
Great videos. Just got the LM2 20W myself and have been binging your content. Commenting for the algo :-)
I did it! It only took me 3 hours!!! ( had lunch, and some of the instructions didn't work first time, I better go back and see if I still have virus check off! )
Always a great video !
Just an FYI on the Laser Master 2 Pro S2 I upgraded from 1.85 to 1.87 after you copy the bin file it auto closes laser drive & powers down laser. I confirmed it did upgrade in Lightburn.
Thanks for the great walkthrough
Thank you so much. You are a great teacher!!!
I have the latest lightburn 0.9.20 but when I right clicked on the “devices” tab but it’s resetting the current device connection. I’m not getting the pop up that you are getting
Me either. Did you figure it out? I'm on day 2 of learning all I can.
Found it by accident or fate. Alarm went off since the laser won't shut down.
@@euphoricstillness nope, I’m still getting the same thing.
@@ryanbeharry5636 Near the move tab is a console tab. When you start up the laser it will automatically home and the message will show up in there. Good luck
You’re awesome! Thanks so much!
Thank you so VERY much.. Keep up the good work..
Great, tried updating to fix a small problem and now the problem is even worse. It won’t turn on at all now. Thanks!
this happened to me what did you do
Happened to me too
You guys ROCK!!!
You're the professor 👍
Thank you very much
Laser burns on full power. $30 & $32 settings are correct. new firmware updated. still cannot adjust power.
PLAESE HELP!!!
I havent followed this advice as yet, and now I am reluctant to change anything after reading all this. This is the message I got whilst trying out my LM2 20w (older version). Starting stream
Layer C01 Pass 1 of 2
Layer C01 Pass 2 of 2
Layer C01
Layer C01
Layer C01
Layer C01
Layer C01
Layer C01
Layer C01
Layer C01
Detect movement, terminate laser engraving!
Acceleration fluctuation:325
Reset Grbl.
Ortur Laser Master 2 Ready!
OLF 137.
Grbl 1.1f ['$' for help]
[MSG:'$H'|'$X' to unlock]
error:9
G-code locked out during alarm or jog state.
On or near line 39911:
Job halted
Stream completed in 50:51
Great video! Does this work the same for the OLM 3?
Thanks 👍👍👍👍👍👍
Good video Jim! But this video is longer than five minutes 😜😜😂😂
Nice video thanks!
Thank you, sir!
My "devices" doesn't do anything if I right-click on it. a left click just brings up the name of the laser it found. I'm wondering how to check the current version of firmware I have?
right clicking not bring up the same menu on devices instead it shows disconnecting and then laser ready. light burn 9.21 windows 11
How can I identify (LU 1-3 20J12 on my unit)the laser module. I want to upgrade, I think the one I have is 4.5 watt.
bonjour j'ai update le firmware de mon ortur laser master2 tous c'est passe correctement mais j'ai un souci le homing avant quand je debranchait l'axe y pour y brancher le rouleau en ayant pris soin de mettre le homming a 0 au lieu de 1 je n'avais pas de probleme mais depuis si je fait cette procedure mon laser se met en alarm sur grbl sauf sur lightburn: pourquoi cdlt serait ce du que j'ai mis le 142
THANKS
Did the upgrade. and then would not start. I did not have clue as what happened.
So after searching for about 6 hours I found the OEM bin file. put it back and back up and running
Tech support. all they could say is try this try that. if there is anyone who had the same problem
let me know what you did to get it back up and running.
Cheers
I'm going thru all these steps, there is no PDF for downloading 1.83 in the firmware repository. thoughts?
Use the newest firmware they offer!
Jim, in the caution note you say not to use the PRO firmware and use the LM or LM2 firmware. I assume that is because you have the LM or LM2 model. I have the LM2Pro so I should be using that version? I'm new to all of this laser stuff so I'm trying to muddle through it all. Thanks in advance.
Use the firmware that is for your laser. If you have the LM2 Pro use that firmware. Good question!
Ok did all that but now my laser is not burning at full power, seems to only be burning at about 25% power. I am using lasergrbl when I click the laser button so I can set the focus the laser shuts off after a few seconds and then I have to reset the Ortur. Anyone have any idea whats going on here. Used my burner a few weeks ago with no issue to burn some Harry Potter coasters. Any help would be greatly appreciated. Thanks
I would try it again and make sure you have the correct firmware for your laser. Otherwise jump on the Facebook group and tag Gil. He is support and he will help you get it worked out!
Hi, I need some help, i have just purchased laser master 2s2, and set it up, the only trouble is the X-axis is not moving, I have checked the cables and when i home the y-axis moves but the x-axis does not, plus the laser GRBL shows an icon that says 'Alarm' can you help?
Hello. I have a question for you. Did you ever test if you can put this machine on the wall and use it like that? to cut some plywood on the wall? Would be really nice if you would be willing to test this. Thank you, and keep up the good job with your videos. I wanted to buy this machine, that why I asked... I am bad with space...
I have old 170 on mine, but I tried this method and it won't stay connected to the PC in my computer. So I cannot update to the latest firmware. I believe the prior owner must have installed the wrong firmware on my machine. It works, but it's not right
Unfortunately, when I try to copy the BIN file over the D drive closes and it gives me an error saying it can't do that. I have a error on lightburn saying "Emergecy Switch Engaged" and the thing just won't do anything. I just put it together, too. So frustrating. I'm waiting to hear back from support. But if anyone knows how to fix this, I would be grateful.
Hey there...I have watched several other videos you have that have been very helpful and have recently subscribed. I tried the firmware update this morning and after dragging the new .bin file over pressing the reset and then the power button get nothing. Was hoping this update fixed a couple disconnect issues in the middle of a few burns but this not powering up thing has me freaked out! I did message Gil and Ortur tech support and am trying to be patient for a reply from either. Is this fixable as far as you know with out having to order new parts???
this happened to me what did you do?
I have a Ortur LM2. I'm having trouble with the drive it creates when I hit the reset button after holding the power. As soon as I try to copy the bin file, the drive disconnects and the file does not copy. Any thoughts? Thank you
I just place an order for a Ortur.
Hello, I just put together the machine, but It shows issues with Expressif CDC device not installed, and I cant find any info on Google. Would someone know the solution? cheers
My laser master 2 never turned back on. My computer keeps reading error :( PLEASE HELP!!
thanks i just update to 187 on light burn 1.1.00 ....
Any idea if the firmware updates are all inclusive of previous ones or do you need to do each one in order. Mine is 1.37 and see there are two other updates. Thanks.
You should just be able to use the newest one!
@@TheEdgeofTech Thanks
So, I followed all the steps exactly as in your video. After I copy and pasted the bin file and hit the reset button the laser turned off, but now I can't get it to power back on. Not sure what to do now. Please let me know if you have any suggestions. Thank you. Your videos are awesome.
Hmm. I know a few others had this issue as well. Jump in the Facebook group and ask Gil, He has the solution I believe!
I need help connecting a comgrow z1
Ciao complimenti per I video che fai, io ho aggiornato i firmware come dici nel video ma il laser non funziona la luce del laser lampeggia.
I'm new to lasers, I have a laser master 2 and it's not showing connected. Where do I go from here?
Why is my computer unable to read my ortur ? (Windows 11)
When downloading the newest firmware from the depository I never get version 1.90. It keeps giving version 1.85. So what is the latest version 1.85 or 1.90? This is a brand new Ortur laser master 2 pro s2
So just went through this whole process and now the unit wont power back on. Everything went exactly as you showed, but after the reset, the power button wont work. Any ideas?
Did you use the pro firmware? If you did, do it again using the regular firmware
please help not find help anywhere i have new version for a while now and keep getting (error:9
G-code locked out during alarm or jog state.) I Have check everything cords power source and reset everything still doing it
Jump on the Facebook group and post their. Tag Gil And we'll get it fixed
i updatet my firmware but now the unit wont power back on.
what kan i do?
Jump on the Facebook group and reach out to Gil. He is their support and will help!
Oké thnx
I am trying to update firmware from 1.1f to 1.1h with no luck! This device does not exist!! What now?
After i update the firmware on my laser, i followed every step now don't turn on, any information why and how to fix it.
thank you.
Jump on the Facebook group and ask Gil for help. I need to ask him what the official fix is, but he's been helping anyone who has this issue!
Thanks for the helpful video. My LM2 Motherbaord replacement came with a power, USB and what looks like an ethernet conector on the front. Is this a Pro Baord?
No it is not. It is just an updated board for the lm2.
Mine said it can't copy. i get an error
Love your videos. I have one problem with this one. first let me say, I just received my Laser so tried The right click devices in to see if already has the new firmware. when doing so the laser Homes but no dialog box appears. What Is wrong or what am I doing wrong? using LB V0.9.24. Any help is greatly appreciated!
Hey upgraded the hardware now it's not working like it used to I have to increase the power to 100 so how do you factory reset the whole thing
Well, just got my laser...put it together, excited to try it...noticed the firmware was not the current one...apparently against my better judgement, followed all the instructions to update and now I'm stuck with it not turning on. Still can get it to mount to the computer but nothing else. I've reached out on the Facebook group so hopefully I can get it sorted but man I'm bummed out.
@Ryan Wargo Make sure you are EXTRACTING the file and not just opening it. The bin file is a different size after you extract it.
just updated mine to and now it wont turn on did you find a fix for this yet
@@Mysticalmantiscreations yes extracted it with WinRAR...which includes the bin file, pdf instructions, and changelog. Pretty sure I can't extract it any further, atleast not with right clicking it.
Sorry man, other than that the only thing I ran into was I didnt have the Pro (which I thought i had) i downloaded the other one that wasnt for the pro and extracted and it worked fine.
@@Mysticalmantiscreations so I thought about that but apparently everybody is supposed to download the standard file because the Pro download is for a different machine not out yet...not for the Pro motherboard
I did the update just fine, cleared everything but now my homing is completely jacked. It is trying to home to the lower right even though everything in the setup is lower left. It can’t find my project on the table and the fan stays on after I try to do a test fire or frame!!!! I have the latest LightBurn and Windows 10. Any ideas?
page not coming up after going thru the steps with laser help please
the firmware link not working
I did the firmware update and my laser will not turn on. I can open the folder as described in your video and drop the firmware in again but the same thing happens again. Have you any idea what I might need to do?
Try renaming the firmware file. That doesn't work Hit up the Facebook group and reach out to Gil. He is there support and will get you up and running!
@@TheEdgeofTech Gil was fantastic, connected via software from his company and repaired ortur in less than 5 minutes. Thanks again for the recommendation. Keep up the good work Jim
Yeah how do you fix this?
Hi, great video.. but I tried the update and somehow I messed up now mi laser isn't responding theorize isn't popping up on my computer, Is there a way to factory reset my laser.
And why should we update the firmware?anything better now or bug fixes??..
Question for ya ...
Can I use Inkscape with my ortur 20 watt laser...
Thanks
Mike
Absolutely! Also look up imag-r as it's an awesome tool as well
Awesome,Thanks appreciate it immensely....
hello ortur Master..i have 2 problems with my ortur l M2..i havent had any problem a year ago..but now the machine working,laser is on,but doesnt burn nothing,with any different settings..and after i have tried to get a firmware,and i followed the process,but the bin file doesnt work,the machine doesnt want to start again?could you help me,how can i fix the problems,i think first the firmware,after the laser...i am working with windows 8...thanks to alll,have a good day 🙂
i did the upgrade and now it wont turn back on help please
Jump on the Ortur group in facebook and post there tagging Gil. He will help you out! He's the support guy!
my olm2 wont power on im in the process of working on this and that with ortur support. May I know what is the name of the facebook group to find Gil to help me.
It's the Ortour Facebook group
When I click the download link nothing happens any idea's on how to correct this
wow, now my laser power button doesn't work. I followed the instructions and when I hit the power button nothing happens. I don't know what to do.
Jump on the Facebook group and ask Gil for help, he'llmake sure you're up and running
@@TheEdgeofTech Thank you so much I appreciate the help. I also ordered a new motherboard.
Hey Jim I did the upgrade following your video, but I have run into a problem of my laser homing to the right not to the left..Help!!!
Same here. Will update if I figure it out.
I believe my problem is that I applied the Pro firmware because of the video pointing out that I had the Pro button layout. But apparently that only means I have the Pro-style motherboard, and not the Pro LM2.
Yup, now homing properly after loading the latest non-Pro firmware.
Same here as the others. Ugh! Laser does nothing now.
@@Mysticalmantiscreations Did you also install the Pro firmware?
Link is in the description?
Which link are you talk about? I'll check to make sure I didn't miss one.
Well I have a good idea why they say dont use a Mac... Linux would have similar things... I bet it works fine if you make sure to unmount the drive after copying the file over.
It seems weird that there would be any problems when the Ortur simply sets up as a USB drive. I could see problems if there was update software needing to be run on Windows to transfer the firmware via a USB serial port connection but this method seems to be better and avoid those issues.
@@ElmerFuddGun yeah typically if you were to not allow the system to fully write to the attached disk before ejecting it may not actually write all the data. Ejecting forced that write to happen. Even in windows you could end up in a state where it did not fully write but that usually happens with very large files. If you have ever copied files on a mac or linux machine it can sometimes take a minute before it will tell you that the drive can be removed.
@@ottersdangerden - True. I don't have any Mac experience but do have Windows and Linux machines. There is a setting (at least in Windows) that can turn that "buffering" on and off on different drives. I always use the "eject" function out of habit and don't see how there would be a problem here. But like I said I don't have a Mac and Apple does do some weird stuff. ;-)
@@ElmerFuddGun turns out it has something to do with the hidden macos folder that gets dropped onto it, so that can cause it to fail. Linux can drop a fille there but that is pretty rare and if you know that is an issue its pretty easy to mitigate. (Liam at astroprint had Ortur support guy and thats where i got this info)
while trying to update the firmware something did not happen. And now the OLM2 will not power on. HELP
This is exactly what happened with mine too.....did you get it resolved and if so what did you do???
Hey me too have you managed to resolve this problem yet if so how did you do it I’d be great full for some help 🙏
now my lm2 pro will not turn on ??? what now ??
Are you sure you have the Pro? I thought I did, because of the way the buttons setup, but apparently that means it's a Pro motherboard, not the LM2 Pro. Caused me problems until I loaded the correct firmware.
Asterisk ✳️
And now my laser doesn't work anymore. Should have just left it as is.
Talk to Gil on the Ortur facebook group and he will get it working for you. He's their tech support!
@@TheEdgeofTech Thanks. Will do.
DANGER i decided to follow your video and the result was that my ortur is now DEAD ! after your video like a idiot i decided to read the manual where it said something you didn't say......" DO NOT USE A USB HUB" connect directly to the PC. Duh .... anyone any ideas how to fix this now ?? its doing absolutely noting any more....😖
Press the reset button then the power button then the reset button again. And then try to turn it back on. Then go through the upgrade instructions without the hub if it turns back on. If it does not turn back on, jump in the ortour group on Facebook and ask Gil for help. He is the support and he will help very quickly.
ok update... disconnected the LM2 from the net and USB ... then reconnected the LM2 to a laptop with a very short usb cable. Then held the Reset button and second later the start button hold both till the light comes on (hopefully, took me 2 runs) then start the whole procedure again....this time with no hub or usb cable extender !!!! PROBLEM SOLVED
If your OLM2 works now WITHOUT any problems... My advice (like with all computer related hardware) DON'T update. That is my experience of 27 years working with computer hardware
well, I don't have a Windows machine, so I'm S.O. L.
After this de laser keep on 100% burning to his home position you now someting ?
[MODEL: Ortur Laser Master 2]
[OLF: 140]
[DATE:17:23:54 - Jan 4 2021]
[VER:1.1h.20190903:]
[OPT:VNZHI,99,254]
Target buffer size found
ok
Naar standaardinstelling
ok
Stream wordt gestart
[MSG:Pgm End]
Stream voltooid in 0:00
Stream wordt gestart
Stream voltooid in 0:00
ok
Stream wordt gestart
Layer C00
[MSG:Pgm End]
Stream voltooid in 0:03
After this de laser keep on burning to his home position
What's the difference between the master 2 and master 2 pro models?