G'day Lord Duckman. A nice fix. Someone is certainly going to be happy with that it really moves. But you proved me wrong. I didn't think you'd fit in that. You would've been a sight hoofing down your street laughing. So thanks for sharing an awesome video man. I thoroughly enjoyed it. ✌️ Peace from Melbourne Australia.
The first thing I do is suck the gas out from the lowest point of the tank. This has bitten my ass so many times!😁 It's either the pissy yellow or water in the fuel. Looks like you have lots of pets again!
There is a low idle jet, it is under the idle screw. You unscrew the idle screw all the way out and use a flat head to pry up the black plastic piece that the idle screw covers up. If its a epa carb, the idle screw might have a tamper cap on it, they usually pop off fairly easily.. theres not much that can go wrong with these carbs. Usually a good deep cleaning and they are good. I never look at the arrows on the belts, the amazon belts are notorius for having the arrows the wrong direction, that was good advise on showing flat side towards the engine.
Thanks for the suggestion, someone else said that one here earlier, I didn't even know that was there and learned something myself. I'll dig deeper into these carbs. Some of them don't even have a proper idle screw. They don't want anyone to tamper, I guess!
@DuckmanCycles yeah most newer engines are coming without a mixture screw, capped off idle screw, and non removable fuel bowl. On top of that, they are jetted super lean to pass emissions. Most of the time, the idle screw is there. It just has a plastic cap on it. So pop off the cap, remove the screw completely, then pry up the pilot jet. They are usually black plastic with a brass jet pressed into the bottom. With a good set of pliers, you can remove the non removable fuel bowl and then replace the headless bolt with a regular bowl bolt. The best fool proof way I've found to clean those little carbs is to remove the bowl, take out both jets, emulsion tube and the mixture screw if it has one, then put everything in a ultrasonic cleaner with mineral spirits or your favorite solvent that's safe for plastics. Then, hit it with compressed air through all of the ports and passages. I know it's cheap to just buy a new carb but I'd rather spend some time than spend some money. Haha.
On your impact have you sprayed a little lube in it and spun the outside of bit holder cause sometimes the balls that hold it in like a airhose fitting will get sticky had one do same thing to me
LoL! Light bulb moment... those stupid chickens from Zelda 3 and onwards.... haha! Don't hit them with your sword, they'll get ya. That's probably what happened to Link.
I dunno why people can't just say it like it is.... what is wrong? JUST SAY IT! Either way it has to be fixed, lol!
G'day Lord Duckman.
A nice fix. Someone is certainly going to be happy with that it really moves.
But you proved me wrong. I didn't think you'd fit in that. You would've been a sight hoofing down your street laughing.
So thanks for sharing an awesome video man. I thoroughly enjoyed it.
✌️ Peace from Melbourne Australia.
Well, I proved you right... I don't fit in it. LoL! I really don't like that thing... haha! Thanks man!
Don't know if your going to say later, but there is an low idle jet under the idle screw. The screw holds it in place.
Thats news to me, actually. I will go In there and look. I never knew that If that's the case! You learned me something!
Good fix Lord Duckman. I would like to see a chicken hatch a duck egg. That would be fun to see. Lol. Noel
The first thing I do is suck the gas out from the lowest point of the tank. This has bitten my ass so many times!😁 It's either the pissy yellow or water in the fuel. Looks like you have lots of pets again!
Yuck glad I got that all out of there
I wonder if some small person, trying to help 'filled' the tank.
LoL I think rain, was no gas in there at all!
Cheeky wants to be a mechanic chicken ❤
I think so, lol!
big kid
And not changing any time soon lol
It’s what keeps me viewing.
It what keeps me making! Hehe 😁👍
There is a low idle jet, it is under the idle screw. You unscrew the idle screw all the way out and use a flat head to pry up the black plastic piece that the idle screw covers up. If its a epa carb, the idle screw might have a tamper cap on it, they usually pop off fairly easily.. theres not much that can go wrong with these carbs. Usually a good deep cleaning and they are good.
I never look at the arrows on the belts, the amazon belts are notorius for having the arrows the wrong direction, that was good advise on showing flat side towards the engine.
Thanks for the suggestion, someone else said that one here earlier, I didn't even know that was there and learned something myself. I'll dig deeper into these carbs. Some of them don't even have a proper idle screw. They don't want anyone to tamper, I guess!
And thank you! That belt story actually happened here in a previous video. I got one with backwards markings, and ruined a belt pretty quickly!
@DuckmanCycles yeah most newer engines are coming without a mixture screw, capped off idle screw, and non removable fuel bowl. On top of that, they are jetted super lean to pass emissions. Most of the time, the idle screw is there. It just has a plastic cap on it. So pop off the cap, remove the screw completely, then pry up the pilot jet. They are usually black plastic with a brass jet pressed into the bottom. With a good set of pliers, you can remove the non removable fuel bowl and then replace the headless bolt with a regular bowl bolt. The best fool proof way I've found to clean those little carbs is to remove the bowl, take out both jets, emulsion tube and the mixture screw if it has one, then put everything in a ultrasonic cleaner with mineral spirits or your favorite solvent that's safe for plastics. Then, hit it with compressed air through all of the ports and passages. I know it's cheap to just buy a new carb but I'd rather spend some time than spend some money. Haha.
Looks like a champion machine 😊
It sure performs well! 😁👍🦆💩
On your impact have you sprayed a little lube in it and spun the outside of bit holder cause sometimes the balls that hold it in like a airhose fitting will get sticky had one do same thing to me
Not had much luck with that, need to clean it out I think. It was abused before I got it, might need new balls lol
@@DuckmanCycles yeah it's a possibility the impacts wife might have them🤣🤣🤣🤣
😯😯😯😯😯
Good Times
Oh yes! Running well again! 😁👍🦆💩
nice ride
Thanks haha
Lots of Cuccos..where's Link?
No idea what you're even on about... who are these names?
LoL! Light bulb moment... those stupid chickens from Zelda 3 and onwards.... haha! Don't hit them with your sword, they'll get ya. That's probably what happened to Link.
@@DuckmanCycles Nintendo characters. Link is the hero in the Zelda games.
Yeah, thats what I had said lol
Those chickens belong as the filling in a chicken roll. Ask me how I know --- because they are in-bread.
😯😯😯😯😯😯😁🤣🤣🤣