Thanks for this video Adam. Your videos really help beginners and make it easier for them to progress in the hobby without having to search the internet hours to find out the basics, (which are overlooked by most rc channels) Also great to see videos on flysky entry level radios and set them up (which is often where many beginners start). 95% of the videos out there target people who have been building and flying for years, it's great to see you make videos for the beginners. Awesome channel! - i have learned alot from you - Thanks!
Hi Adam , I have a Flysky FS I6x like you show in your video ,I have done all the steps as you shown but when I plugged in to my flight controller I can not connect the transmitter with the receiver . Yesterday I did connect them and even done the radio calibration, today I tried everything again I couldn’t get to connect them . I created an Sbus cable myself and like I said it did work yesterday . Any help or suggestions will be highly appreciated Adam ,thank you !
hi there i done all steps but when switch arm button but in drone motore dosent spin at all just make sound that arm switch is on then when try to fly only some motore works but its then its stops can you please me im iew in fpv really need help i am using same f3 board and turnigy tyg i10 reciver
I could use some major help.... i have bouned my fly sky radio to my reciever but when I connect it to betaflight nothing happens.... i have done some trouble shooting... is there anything I should try?
My f4 flight controller works fine in betaflight, but it doesn't respond to the motors when fully armed. The receiver tab shows that my transmitter stick motions respond. The motors tab shows the motors responding in betaflight using there variable sliding switch. I don't know why the motors don't run/respond using my transmitter. Please help. The flight controller firmware is MATEKF405. The 4-in-ESC is using BL_S firmware with DSHOT600 protocol.
Hi, my quad don’t response to throttle from transmitter when arm instead it remain on constant speed, but the yaw, pitch and roll working perfectly. Is there any setting I should do ? Any suggestion would be appreciated.
I have the wizard x220 and I got a flysky FS-i6X with the FS-IA6B, I setup everything in betaflight and it should work but for some reason when I try to arm nothing happens only the red light blinks and thats it, I can spin the motors in betaflight just not with the controller
so i had arming for the swa switch but that switch was also turning on trainer mode so I switched trainer mode to some other switch and it works but then after flying for a bit one of the esc's caught fire so I got some new ones. Thanks for everything!
cool thanks for this. after working towards the goal i have it arming and spinning motors in betaflight along with stick movements. green light on vista and receiver. green light on transmitter. video feed in goggles at my desk. sweet. unplug everything. screw props onto motors. mount components and maybe i nicked the camera cable in the process unknowingly. go to a field. quickly realize i cannot arm and low power mode unable to record in goggles and no video feed happening. like wut.
plugged into usb can arm. i jumped the pwr leads on my radix2 fc, and per the instructions had it wired to vtx+, which wasnt powering. powering off battery leads directly as following other instuctional videos out on how to wire the caddx vista, does this conflict with my arming protocol, as i have it selected in modes and all works when connected to betaflight. blessings.
@@lyndajones1133 what transmitter and receiver are you using? Also, "low power mode unable to record" is a common inconvenience with the vistas due to lack of cool when there is no airflow to cool it down. Once you arm and have the props spinning you should be able to record.
Hi! Is the quad in auto level mode? If so, this is normal. Try using the betaflight controls to spin up all motors at once to see if they spin up evenly.
drive.google.com/folderview?id=1CZBFLXsUDNjVt8-Zqy0M70nFUWfFxZp_ it's a signal booster I've had on for a while powered from a 3s in my pocket. Antennas are 10dbi for the turbowing and 5dbi on the tx. Getting about 2.5km range with 40+ rssi. Still going to modify turbowing position to be able to use port for sims.
dope i got a question, i bought a drone on letgo and forgot what the arming switch was.how do i reset it, if im not sure if the original owner used betaflight of cleanflight?
@@RCwithAdam1 whats up, hope you and your are safe and healthy. the drone is a atom v2 and nah i cant see any writing on the flight controls.lol please tell me i didnt wast my money??
Thanks! You as well! I found this Atom V2 manual docs.google.com/document/d/1zT_LAbNWP8edU813GhpSn6dZ2wrR0J0CP_KyM7wGYyw/pub, and it looks like they were using cleanflight at the time. What I would do is just try flashing the flight controller with a new version of Betaflight firmware.
Question I bought a random trs to trrs adapter from eBay. Will it work it’s brand new. Does any trs to trrs converter make you use microphones on your phone ? Hopefully 🤞🏼🤞🏼 my mic is a rode mic and the adapter just says headphone earphone audio trs to trrs adapter Link to the adapter : www.ebay.co.uk/itm/383465179665 This is the mic :www.thomann.de/pics/bdb/177309/7270763_800.jpg Thanks in advance Waiting for good news hopefully
wow just when i think im getting help i go aaaaaaaaaaaaaaaalllllllllllllllllll the way down on my FS-i6 and there no fucking aux switches below the factory reset option lol fucking great
way to old man update everything. not trying to be a jerk man but your channel ends are all off that whole quad is set up wrong go watch bardwells video before you post your own or someone will get hurt
Did YOU remember to take off YOUR spinny-blades? ⚔️
Yes.
Thanks for this video Adam. Your videos really help beginners and make it easier for them to progress in the hobby without having to search the internet hours to find out the basics, (which are overlooked by most rc channels)
Also great to see videos on flysky entry level radios and set them up (which is often where many beginners start).
95% of the videos out there target people who have been building and flying for years, it's great to see you make videos for the beginners. Awesome channel! - i have learned alot from you - Thanks!
I'm so glad you're enjoying them! And thank you for the encouragement!😁
same!
brew. i love You so much. U was only one who explain how to disarm drone.
OMG THANK YOU SO MUCH I DIDNT KNOW WHAT WAS WRONG WITH MY DRONE AND THIS IS THE MISSING PEICE TANK YOU SO MUCH!!!!
Hi Adam , I have a Flysky FS I6x like you show in your video ,I have done all the steps as you shown but when I plugged in to my flight controller I can not connect the transmitter with the receiver . Yesterday I did connect them and even done the radio calibration, today I tried everything again I couldn’t get to connect them . I created an Sbus cable myself and like I said it did work yesterday . Any help or suggestions will be highly appreciated Adam ,thank you !
hi there i done all steps but when switch arm button but in drone motore dosent spin at all just make sound that arm switch is on then when try to fly only some motore works but its then its stops can you please me im iew in fpv really need help
i am using same f3 board and turnigy tyg i10 reciver
I could use some major help.... i have bouned my fly sky radio to my reciever but when I connect it to betaflight nothing happens.... i have done some trouble shooting... is there anything I should try?
Do you know how many ibus channels are supported with the receiver you are using in this video? Thanks!
My f4 flight controller works fine in betaflight, but it doesn't respond to the motors when fully armed. The receiver tab shows that my transmitter stick motions respond. The motors tab shows the motors responding in betaflight using there variable sliding switch. I don't know why the motors don't run/respond using my transmitter. Please help. The flight controller firmware is MATEKF405. The 4-in-ESC is using BL_S firmware with DSHOT600 protocol.
Same problem 😂
Can I use 4ch flysky fsi4x transmitter with fpv
thanks Adam this really helped!
Thanks for your help 👍👌😊
You bet! 👍
Hi Adam ,do you use Ardupilot ?
Hi! Not at this time, but I am learning.
Thanks so much for the help
Can you use Cleanflight to set up the ARM switch also or do you have to use Betaflight?
You can do the same thing on cleanflight, but that configurator is obsolete now. Everyone just uses betaflight now.
Hello I have the flywoo drone and my bind button got broken smh is it some other way I could bind my radio T18
Have been using my drone with the Eachine i6 controller. For some reason it will no longer bind (no RX). Any ideas? TIA
Hi! What receiver are you using? Did the drone crash or get damaged at all?
Is 2s lipo battery sufficient to arm fpv drone kindly help
It might be. It depends on the specific drone.
@@RCwithAdam15 inch 4 eco 2207 1900kv motors,speedybee f405 FC and fsia6b rx and fsi4x tx but I am unable to arm the drone
Hi, my quad don’t response to throttle from transmitter when arm instead it remain on constant speed, but the yaw, pitch and roll working perfectly. Is there any setting I should do ? Any suggestion would be appreciated.
Hi! What quadcopter and receiver are you using?
I am unable to arm my fpv need help i am using 2s battery
Can you help me with my x220s. Please
I have the wizard x220 and I got a flysky FS-i6X with the FS-IA6B, I setup everything in betaflight and it should work but for some reason when I try to arm nothing happens only the red light blinks and thats it, I can spin the motors in betaflight just not with the controller
fixed it
Glad you got it working! What was the issue?
so i had arming for the swa switch but that switch was also turning on trainer mode so I switched trainer mode to some other switch and it works but then after flying for a bit one of the esc's caught fire so I got some new ones. Thanks for everything!
cool thanks for this. after working towards the goal i have it arming and spinning motors in betaflight along with stick movements. green light on vista and receiver. green light on transmitter. video feed in goggles at my desk. sweet. unplug everything. screw props onto motors. mount components and maybe i nicked the camera cable in the process unknowingly. go to a field. quickly realize i cannot arm and low power mode unable to record in goggles and no video feed happening. like wut.
plugged into usb can arm. i jumped the pwr leads on my radix2 fc, and per the instructions had it wired to vtx+, which wasnt powering. powering off battery leads directly as following other instuctional videos out on how to wire the caddx vista, does this conflict with my arming protocol, as i have it selected in modes and all works when connected to betaflight. blessings.
@@lyndajones1133 what transmitter and receiver are you using? Also, "low power mode unable to record" is a common inconvenience with the vistas due to lack of cool when there is no airflow to cool it down. Once you arm and have the props spinning you should be able to record.
When I switch the aux to on position, 4 motors are turning with no balance. First one turns around 1200, second turns around 1300 etc.
Hi! Is the quad in auto level mode? If so, this is normal. Try using the betaflight controls to spin up all motors at once to see if they spin up evenly.
Is beta flight free?
I got a i6x signal booster and battery mod you might like
Very cool! links?
drive.google.com/folderview?id=1CZBFLXsUDNjVt8-Zqy0M70nFUWfFxZp_ it's a signal booster I've had on for a while powered from a 3s in my pocket. Antennas are 10dbi for the turbowing and 5dbi on the tx. Getting about 2.5km range with 40+ rssi. Still going to modify turbowing position to be able to use port for sims.
dope i got a question, i bought a drone on letgo and forgot what the arming switch was.how do i reset it, if im not sure if the original owner used betaflight of cleanflight?
Hi! What model of drone is it? Can you see any writing on the flight controller?
@@RCwithAdam1 whats up, hope you and your are safe and healthy. the drone is a atom v2 and nah i cant see any writing on the flight controls.lol please tell me i didnt wast my money??
Thanks! You as well! I found this Atom V2 manual docs.google.com/document/d/1zT_LAbNWP8edU813GhpSn6dZ2wrR0J0CP_KyM7wGYyw/pub, and it looks like they were using cleanflight at the time. What I would do is just try flashing the flight controller with a new version of Betaflight firmware.
Can any one help me with fs r9b receiver? Which channel I should connect the servo ?
Question I bought a random trs to trrs adapter from eBay. Will it work it’s brand new. Does any trs to trrs converter make you use microphones on your phone ? Hopefully 🤞🏼🤞🏼 my mic is a rode mic and the adapter just says headphone earphone audio trs to trrs adapter
Link to the adapter : www.ebay.co.uk/itm/383465179665
This is the mic :www.thomann.de/pics/bdb/177309/7270763_800.jpg
Thanks in advance
Waiting for good news hopefully
Sir i have fs14x and does not arm drone
First view...hi bro...am also having a i6x. Can you made a video of rctimer atlas flight controller review and full setup
Hi! Sorry, I don't have one of those right now.
@@RCwithAdam1 yeah ok bro..thanks for reply :)
I click save and nothing happens?
im using a fs i6 and when I go into system setup, aux switches does not appear for some reason
Hi! Can you tell me which firmware version you use?
@@RCwithAdam1 have same problem, firmware 2.0 1-feb-2018
@@kamy2020 same problem here
so im new to all rc things i need a beginners guide on what drone to get what to do with flysky pls just make a vid for complete beginners
wow just when i think im getting help i go aaaaaaaaaaaaaaaalllllllllllllllllll the way down on my FS-i6 and there no fucking aux switches below the factory reset option lol fucking great
fucke me , you save the day . thanks
save yourself some time and just get frsky or crossfire.
*and spend a lot more money
@@VijitChandna ...that will actually save you money in the long run
Guys plz dont buy the wizard x220 and a flysky radio buy FRSKY for like 30 boucks more plz
Hi! Can you give a link?
RCwithAdam banggood.com banggood.app.link/PZ4OAWBkR5
way to old man update everything. not trying to be a jerk man but your channel ends are all off that whole quad is set up wrong go watch bardwells video before you post your own or someone will get hurt
Hi! In this video I'm just focusing on how to setup the arm switch, nothing else. Thanks for the comment though.