I’m going to unscrew the back and flush out the lint. Are these the service modes that I use? I don’t want to pay almost $200 for a serviceman to come and do it like I usually do.
I get EHE, the unit appears to be double insulated and has an internal Earth leakage circuit which trips. I suspect an aging motherboard or power board. Anyway I reset as above all good.
Hello and ty for information. I got the same dryer. today "drying phase" indicator started to blink an its not heating up anymore. Starts to work for a few seconds and the timer goes on but it is not working. any idea why?
It is because of the door I had the same problem. Check pushing the door and start the program if it doesn’t stop in a couple of minutes. That’s the problem. Check out the latch or the pin. Usually E32 error is because of the pin.
Hej mats försöker skriva till dig för din ac påfyllningsmetod vad använde du för munstycke till ac påfyllningen i bilen och hur gjorde du slangen såg väldigt smart ut vill testa samma sak ?
Can I ask you what exactly does this e32 to you? I know its related to humidity sensor, but i haven’t found how the dryer behaves with this error. I’m not sure if the error is relevant for my issue… thanks
Very use full coz my machine it shows firt time EHO i changed the pcb not working machine then again i enter the diagnosed mode then it shows E64 then i checked the heater no isuue it then again diagnosed mode check clear all arlams but again never come back EHO and E64.afer it show E 32 i did rest cant rest it..i think real fault is moisture sensor...once i rest again coming back
@@okornel this dry is runing but not heating... I changed the pcb nothing wil happen.... If you connect together that humidity sensor wire so it is was starting heat up the dryer. so I order new humidity sensor......that time showed no alarm
I’m going to unscrew the back and flush out the lint. Are these the service modes that I use? I don’t want to pay almost $200 for a serviceman to come and do it like I usually do.
I get EHE, the unit appears to be double insulated and has an internal Earth leakage circuit which trips. I suspect an aging motherboard or power board. Anyway I reset as above all good.
Thank you it’s really working
I am applying for my machine
What if it still says error after resetting?
Hello and ty for information. I got the same dryer. today "drying phase" indicator started to blink an its not heating up anymore. Starts to work for a few seconds and the timer goes on but it is not working. any idea why?
Hi, my dryer has exact same faultcode but for some reason if I reset, the fault comes right back. Do you have an idea what to do next?
It is because of the door I had the same problem. Check pushing the door and start the program if it doesn’t stop in a couple of minutes. That’s the problem. Check out the latch or the pin. Usually E32 error is because of the pin.
Hej mats försöker skriva till dig för din ac påfyllningsmetod vad använde du för munstycke till ac påfyllningen i bilen och hur gjorde du slangen såg väldigt smart ut vill testa samma sak ?
HELLO. How can I send you a picture of the icon, when I turn on any program I have an icon in the online machine and the program does not start.
Can I ask you what exactly does this e32 to you? I know its related to humidity sensor, but i haven’t found how the dryer behaves with this error. I’m not sure if the error is relevant for my issue… thanks
The machine stops in the middle of the program. After resetting, it goes fine again for a few months ...
Tanks and it’s helpful video 👍
Very use full coz my machine it shows firt time EHO i changed the pcb not working machine then again i enter the diagnosed mode then it shows E64 then i checked the heater no isuue it then again diagnosed mode check clear all arlams but again never come back EHO and E64.afer it show E 32 i did rest cant rest it..i think real fault is moisture sensor...once i rest again coming back
@@okornel this dry is runing but not heating... I changed the pcb nothing wil happen.... If you connect together that humidity sensor wire so it is was starting heat up the dryer. so I order new humidity sensor......that time showed no alarm
👍👍🙂🙂
can you please help me with HT33K8126 its working just on time drying
Tnx a lot No more error
👍👍👍🙂🙂🙂
Hello I got a separate power button but the rest looks the same. How to reset this model. EDC2086gdw
Thank you this helped me very much
Very helpful!! Thanks
Thanks ! I did and saw no errors after changing drive belt. But now i get "Err" in display ? Cant start any programs, anyone know what to do ?
Did you work it out? I currently have the same problem
@@NRG450 Nope, i bought New machine.
@@tomi3788 I just worked it out, the tab to hit the door closed switch was out of alignment. Adjusted it, now its working. Thanks for the quick reply
👍💯Thank you!!!
I have EHO sign and no matter what I try, the probelm cannot be fixed :(
👍👍🙂🙂🙂🙂🙂
i have error code E52, what can i do, the machine doesnt heat
Thank you !
Good 👍🙂🙂
Thank you
Ayaw umandar now lang pa 2 years palang. 10 years warranty nakalagay
Thank you for the help 🙏
No puedo quitarle el candado
pulsa las dos teclas arriba izquierda con dibujos de candado x 10 seg
Thanks alot it was helpful 👍
Bos mesin sering error E70 knp ya bos
Se a bloqueado con el icono del candado
👍👍🙂🙂
Thank yuo fór the help
Ayaw mag start
Your not explaining anything
En español
Thank you !!!
Thanks
It’s very helpful