LOL, well to be honest it was the only hooded sweatshirt I had with me at work that day, and it was a bit chilly when we shot the video. Good callout though!
How in the world do you not have interference with the mega and the 360. I have a helix 12 for my mega and a helix 10 for my 360, the mega live is perfect when it’s on by it self but when I turn on the 360 I have lines on my mega live the, ( the helix 12) any advice would be greatly appreciated
Could the Mega Live be mounted to the 360 shaft? I'm bothered by the idea of mega live being on my Ultrexx because of how much I use spot lock. I was thinking about some sort of offset that would clamp onto the 360 shaft such that it would sit below the 360 transducer (I have the original 360, not Mega) in just about the same place as if it were mounted on the Ultrexx shaft.
DO NOT MOUNT TO THE 360! I think you would want a separate system to control your MEGA Live! Give the LiveFOOT a look! Here is a link to it on our website! www.bassboatelectronics.com/online-store/Live-Foot-Patented-Motor-Control-System-for-Sonar-Transducers-by-Blitz-Lures-p455234007
Humminbird tech support says not to connect a US2 transducer, y-cable, and Mega 360. Since you only have one unit on the bow, are getting HW 2D from the console unit? Or did you connect the US2 to the y-cable anyway with the adapter? Just curious because I know it "kinda" works until the US2 fails.
We did! We have not had any issues. If you leave the unit on and the TM is out of the water I guess it could damage the US2 however we have not seen any failures in the field.
I have a question... Why are you wearing a Garmin hoodie going over Hummingbird units????
LOL, well to be honest it was the only hooded sweatshirt I had with me at work that day, and it was a bit chilly when we shot the video. Good callout though!
No harm meant I was just hacking on you a little... I'm a bit old school... Very good video my friend , may God bless you and your family... Don
@@chadphillips4087 OMG, that is why I came to the comments section. A boat that seems sponsored by Johnson Outdoors and a Garmin hoodie, lmao!
Yeah you really have to have a unit just for the 360 it just shows so much real estate
How in the world do you not have interference with the mega and the 360. I have a helix 12 for my mega and a helix 10 for my 360, the mega live is perfect when it’s on by it self but when I turn on the 360 I have lines on my mega live the, ( the helix 12) any advice would be greatly appreciated
running MEGA Live through the five port switch will reduce most if not all crosstalk, It is not interference.
What mount is that you’re using for the 360
www.bassboatelectronics.com/online-store/LOW-PRO-360-MOUNT-p500620886
Question, when fishing shallow with the 360 and live, raising your trolling motor isn't that going to cause issues with spacing for the live and 360?
It will cause issues when using the Ultrex 360 on an ultrex.
What is the fortrex 360 mount clamped on the ultrex at?
Question for mega 360 power hookup to your port box. Were did u connect the ground wire??
To the Negative Bus block in the bow. This boat has an custom wire harness that we built.
Thank you so much for your reply 👏👏👏👏👏👏👏 I will take care of this tomorrow.
Could the Mega Live be mounted to the 360 shaft? I'm bothered by the idea of mega live being on my Ultrexx because of how much I use spot lock. I was thinking about some sort of offset that would clamp onto the 360 shaft such that it would sit below the 360 transducer (I have the original 360, not Mega) in just about the same place as if it were mounted on the Ultrexx shaft.
DO NOT MOUNT TO THE 360! I think you would want a separate system to control your MEGA Live! Give the LiveFOOT a look! Here is a link to it on our website!
www.bassboatelectronics.com/online-store/Live-Foot-Patented-Motor-Control-System-for-Sonar-Transducers-by-Blitz-Lures-p455234007
Great video but wearing a Garmin shirt installing humminbird electronics? Just seems odd advertising one brand and installing another.
It’s what we do! We sell and install them all!
How many times is mega 360 coming out of water? Is that a 45” or 52” ultrex?
Do you have a 45 inch shaft on the trolling motor?
We do!
Where can I get a low pro mount for a Fortrex 360?
Would you not want to use the Fortrex 360?
What if your getting interference on the 360?
Is that a 52”ultrex?
Can you run Mega 360 and mega live at the same time with no interference?
YES! When it is properly setup!
So what’s the proper setup
Get a str8-upmount
Humminbird tech support says not to connect a US2 transducer, y-cable, and Mega 360. Since you only have one unit on the bow, are getting HW 2D from the console unit? Or did you connect the US2 to the y-cable anyway with the adapter? Just curious because I know it "kinda" works until the US2 fails.
We did! We have not had any issues. If you leave the unit on and the TM is out of the water I guess it could damage the US2 however we have not seen any failures in the field.
@@BassBoatElectronics wait you can use ycable with us2? Have you had any problems yet?