9v is better than anything else. Portable. Battery will last longer. Can go to 7.5v and still work. Great work. Dont let anyone complain. They can make their own videos 👍
I would like to see the actual developers of this project get the credit they deserve. Working a little with the soldering iron and the glue gun somehow gives the impression that you have developed the part. But the development of the software in particular would overwhelm 95% of UA-camrs who post such videos here. A little honesty wouldn't be out of place. How would you like it if I passed off your work as mine?
I made the project with CRODUINO basic 3 percent I'm from Croatia but the display results were not very accurate from the elements so instead of C1 capacitor located on GND I AREF I put a RESISTOR of 2.2 k and the results of electrical elements were much more accurate. If someone has the same problem, try a resistor.
All these "tester" uploads are simply one copying the other, misinformation and all. Nobody stops to look at the original design by Karl Heinz. (Genius piece of work) The original design documentation clearly reads that the AREF cap has an influence on some calculation TIMINGS, but not critical. The original design suggest 1nF , but can be more. It has nothing to do with "capacitor" accuracy readings. From the original documentation; "The 100 nF capacitor on pin 21 (AREF) can either be removed completely or better replaced with a 1 nF capacitor." So in the end you are not wrong....
It's giving these errors: In function 'void setup()': 343:14: error: return-statement with a value, in function returning 'void'[-fpermissive] 1421:18 error expected '}' at end of input 642:14: error: l
Hiya East Tech. Could you please upload the Arduino code again please as I am unable to program the Nano. The Arduino IDE keeps giving me errors reports. Thank you kindly. Regards, Marty (UK)
Merhaba hocam LCR Metreyi Nokia 5110 LCD ekranı kullanarak yapabilirmiyiz ŞİMDİDEN TEŞEKKÜRLER Hello sir, can we make the LCR Meter using the Nokia 5110 LCD screen? THANKS IN ADVANCE
MEH, you need to add component costs ! How much was the plastic box ? How much was the on/off switch? etc etc. You will find the 'Project' will quickly add up to a great deal more than it would cost to just buy a component tester when the opposite should be the case. Too many scalpers out there reselling and making self builds more expensive than buying direct from manufacturer.
Why?! Why you voltage up 9 volt? Arduino will drop it to 5 volts! You just use energy to heat up the voltage regulator on the arduino and faster discharge accumulator. You can set boost converter to 5 volt and connect to VCC on arduino for energy saving. Why you group pins by 2, 2 and 2? You need correct component connectors for using it! You can use groups like 2, 1 and 3 and you make using this device easier! Or for better I recomend use zif socket for connection, and maybe, add banana socket for using another probe. I beleve, this project can be better!
Soy un aficionado a la electrónica de 79años y me a dado por hacer este aparato pero no consigo q funcione la pantalla se ilumina pero no sale ningún mensaje serías tan amable de explicarme que es lo que puede pasar un saludo muy afectuoso
I HAVE GOT AN ERROR ardutester_final:1230:8: error: 'class LiquidCrystal_I2C' has no member named 'init' lcd.init(); ^~~~ exit status 1 'class LiquidCrystal_I2C' has no member named 'init' LET ME KN0W THE PROBLEM ASAP
Very cool project.
I think it's time to sharpen up those drill bits though. 😁
Nice job. Add some 18650's and a TP-4056 and your set.👍
9v is better than anything else. Portable. Battery will last longer. Can go to 7.5v and still work. Great work. Dont let anyone complain. They can make their own videos
👍
U
Sir best Project I have Till Now
I would like to see the actual developers of this project get the credit they deserve. Working a little with the soldering iron and the glue gun somehow gives the impression that you have developed the part. But the development of the software in particular would overwhelm 95% of UA-camrs who post such videos here. A little honesty wouldn't be out of place. How would you like it if I passed off your work as mine?
his diy build is his own
@@RichardKight555 You obviously don't understand what I'm talking about.
@@snooker216 I understand but downplaying someone's skill is rude
nowhere in this video makes me think he wrote the coding for the Arduino
Now you nearly got it. What you call rude is exactly what he did with the deleloper's skills.@@RichardKight555
thank's...I need it. I will made it...Thank's you very much
Very good project 👍
Love the tip of how to get a good looking cutout for the display I will certainly by using that technique!
Just FYI: breathing fumes from burning plastic is a bad idea. ;)
Good amazing project and good night 🌃
Use front graphic stiker with lamination.
It's awesome project
If i use Arduino nano atmega 168p it will work?
I made the project with CRODUINO basic 3 percent I'm from Croatia but the display results were not very accurate from the elements so instead of C1 capacitor located on GND I AREF I put a RESISTOR of 2.2 k and the results of electrical elements were much more accurate. If someone has the same problem, try a resistor.
Can you please explain to me why
What's the difference between putting a resistor or a capacitor ? How they work in this situation
All these "tester" uploads are simply one copying the other, misinformation and all.
Nobody stops to look at the original design by Karl Heinz. (Genius piece of work)
The original design documentation clearly reads that the AREF cap has an influence on some calculation TIMINGS, but not critical. The original design suggest 1nF , but can be more. It has nothing to do with "capacitor" accuracy readings.
From the original documentation; "The 100 nF capacitor on pin 21 (AREF) can either be removed completely or better replaced with a 1 nF capacitor."
So in the end you are not wrong....
Amazing project ☺️☺️.
Hi, awesome project. I bought all the parts but cannot access your website for code and diagram. Can you help please?
Amazing project
Code and circuit diagram not available
Plz share it asap
Great project! Thank you kindly! I would love to see a project for an Op-Amps tester. Great work and kindest regards, Marty (UK)
Martin its working ...?
@@aslammeethal3876 Hiya. I have not yet built it. I'm struggling to get some parts. I wll reply when I have built and tested. Thanks, Marty (UK).
Wire from resistor should as short as possible because they will give extra resistance cap and inductance
Very good
Perfect , goodluck.
Totally disappointed by the video. There no circuit diagram is provided. Code provide at which site is not working. 😢
Website working but schematic not provided
Very Cool🥰🥰
#TheProjectLab
Bro nice
Why the 470k 680 resistor combination
wow!! very nice tutorial
Hello, excuse me, but I have foud the code, but not the diagram ... Can you send me one please ? Thanks you for your Idea !
15:34 why it shows value in uF bcz there is no capacitor inserted
It's giving these errors: In function 'void setup()':
343:14: error: return-statement with a value, in function returning 'void'[-fpermissive]
1421:18 error expected '}' at end of input
642:14: error: l
No wiring diagram via link or website. Please provide, Very hard to follow your quick video clips.
This code compatible for arduino uno ? Or need to any changes..?
can you please send me the code?
no worries same code will work
Hi i cant find the wiring diagram nowhere can someone help me please it for a school project for my daughter :)
You uploaded this video before
Anyway amazing work
@@mr.techinventor3463 but time waste
Whats accuracy?
bro please tell us what are needed library for this code. we get a lot of error
Nice
What are the resistors size ?
Hiya East Tech. Could you please upload the Arduino code again please as I am unable to program the Nano. The Arduino IDE keeps giving me errors reports. Thank you kindly. Regards, Marty (UK)
Where can I find the schematic diagram???
Excellent 👍👍👍whaoooooo
Merhaba hocam LCR Metreyi Nokia 5110 LCD ekranı kullanarak
yapabilirmiyiz ŞİMDİDEN TEŞEKKÜRLER
Hello sir, can we make the LCR Meter using the Nokia 5110 LCD screen? THANKS IN ADVANCE
I want this product. How to get it.
it says:
compilation terminated.
exit status 1
LiquidCrystal_I2C.h: No such file or directory
how can i solve this?
Hey i had the same problem i really need help too it said it in the black box below of the IDE
What is the measurable value of the maximal component
You already made this few months ago😅
@@susantamondal9940 yes, every video comes with a big Butt😁
Good work. The link to the code doesn't work
Sir please make a vedio of upload of code
Because when I entered this code their were so many faults
MEH, you need to add component costs ! How much was the plastic box ? How much was the on/off switch? etc etc. You will find the 'Project' will quickly add up to a great deal more than it would cost to just buy a component tester when the opposite should be the case. Too many scalpers out there reselling and making self builds more expensive than buying direct from manufacturer.
If you do not mind spending more money and time then go for it. I would rather buy
a T328 mega LCR tester $8.
the link of the code is not working can you send it please
3.7 volts high to 9 volts and then with losses to 5 volts.
Why not unsolder the linear regulator and use 5 volts straight away?
Good!
Keep going, I love you 😍😍
Combien de coute sa ? merci
Why?!
Why you voltage up 9 volt? Arduino will drop it to 5 volts! You just use energy to heat up the voltage regulator on the arduino and faster discharge accumulator. You can set boost converter to 5 volt and connect to VCC on arduino for energy saving.
Why you group pins by 2, 2 and 2? You need correct component connectors for using it! You can use groups like 2, 1 and 3 and you make using this device easier! Or for better I recomend use zif socket for connection, and maybe, add banana socket for using another probe.
I beleve, this project can be better!
NO DIAGRAM NO EXPLANATION
👌👌👌
9:30......which was that blue pcb?
arduino nano
Soy un aficionado a la electrónica de 79años y me a dado por hacer este aparato pero no consigo q funcione la pantalla se ilumina pero no sale ningún mensaje serías tan amable de explicarme que es lo que puede pasar un saludo muy afectuoso
puede que sea el contraste de la pantalla, chequeate eso.
Hi
không có sơ đồ làm ơn
ye router ups ki box ke andhar kya tha woh dikhao
Bhai as a ek muje bi bna do plz
Cod uploading error
the files was corrupted
Code ??
Link broken
Were ... buying 1 pice rqrd
😉👍👍👍👍
Voltage test nahi kye
Never use a voltage booster like this! If the battery voltage gets too low it will boost the voltage output and fry the Arduino! Terrible video!
👌👌👌👌👍👍👍👍😍😍😍🌹🌹
Old video fir se upload kar diya...🤦
I HAVE GOT AN ERROR
ardutester_final:1230:8: error: 'class LiquidCrystal_I2C' has no member named 'init'
lcd.init();
^~~~
exit status 1
'class LiquidCrystal_I2C' has no member named 'init'
LET ME KN0W THE PROBLEM ASAP
Download liquid crystal library